Citronic Z5M Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Citronic Z5M (3 pagina's) in de categorie Mengpaneel. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
Zoning Mixer
Z5M 953.019
User Manual
Features:
Fully balanced signal path
Stereo/mono operation
Dual stereo line inputs
Separate A & B source level per channel
www.citronic.com
Introduction:
Thank you for choosing this Citronic zoning mixer. Z5M is a professional 1U mixer offering many features to give versatile The
control for up to 5 stereo output zones. In order to achieve the best results from this equipment and avoid damage through
misuse, please read and follow these instructions and retain for future reference.
Warning:
To prevent the risk of re or electric shock, do not expose any part of the unit to rain or moisture.
If liquids are spilled on the surface, stop using immediately, allow unit to dry out and have checked by qualified personnel before
further use.
Avoid impact, extreme pressure or heavy vibration to the unit.
There are no user serviceable parts inside the Z5M refer all servicing to qualified service personnel.
Safety
Check that the supplied mains lead is in good condition and the supply voltage is correct.
Ensure signal leads are of good condition and connected to appropriate inputs/outputs
Do not allow any foreign particles to enter the unit through control or connector apertures
Placement
Keep out of direct sunlight and away from heat sources.
Keep away from damp or dusty environments.
When rack-mounting, avoid placing heavy units above the unit and ensure all connectors and controls are accessible
Cleaning
Use a soft cloth with a neutral detergent to clean the casing as required
Use a soft brush to clear debris from the control surface
Do not use strong solvents for cleaning the unit.
Front Panel
Rear and Side Panels
6. LINE 2 le & right inputs (balanced XLRF)
7. LINE 1 le & right inputs (balanced XLRF)
8. ZONES 1 to 5 le & right outputs (balanced XLRM)
9. IEC mains inlet and fuse
10. Side panel voltage switch
1. POWER switch and indicator
2. LINE 1 source volume controls per channel
3. MONO mode switch and indicator
4. LINE 2 source volume controls per channel
5. LINE 1 and 2 signal indicators
Applications
The Z5M can be used for any multi-output setup and is ideally suited to controlling a multi-room zoning sound system with up to 5 stereo or
mono zones. Individual zones can be selected as mono if speaker placement is not conducive to stereo imaging. 2 separate stereo inputs can be
selected or blended at will for each zone, opening up the possibility of separate program material for specific zones. Prior to rack-mounting the
unit, it is important to know what the mains supply voltage will be, since the voltage selector is situated on the side panel towards the rear of the
unit.
Connection
All connections are via balanced XLR and operate at line level. Use good quality XLR signal leads to connect the source signals to LINE 1 and
LINE 2 inputs. Each output should be connected to the respective amplifier or active speakers for the particular zone, again using good quality
XLR signal leads. Connect mains using the supplied IEC lead.
Operation
Set amplifier and active speaker volume levels fully down
Set LINE 1 and LINE levels for each zone 2 to “MIN
Select MONO for any zones that are better suited to mono output.
Press the POWER switch on and play the signals connected to LINE 1 and LINE 2 inputs.
The LINE SIGNAL LEDs should indicate the presence of each input signal.
Gradually increase and then decrease the volume for LINE1 and LINE 2 to each zone in turn to check the output.
Set the volumes and adjust for each source to each zone as required.
Before powering the Z5M down, turn down amplifier and active speaker volumes to avoid loud noises through the speakers.
SPECIFICATIONS
Item
Value
Power supply
115/230Vac 50/60Hz - selectable (IEC)
Inputs
Line 1 L+R, Line 2 L+R, balanced XLRF
Outputs
Zone 1 to 5 L+R, balanced XLRM
Input impedance
40kohms
Output impedance
220ohms
Frequency response
20Hz - 25kHz, +0/- 1dB
Signal to noise ratio
>100dB
THD
<0.005%
Dimensions
483 x 175 x 44mm
Weight
2.2kg
TROUBLESHOOTING
No function and Power switch LED is not lit
Ensure mains voltage is correct (check selector) and connected properly
Ensure front panel power switch and mains outlet switch are on
Power is on but no audio output
Check all XLR leads are OK and connected properly
Check that LINE 1 and LINE 2 controls are not all turned fully down
Check that inputs and outputs are connected the correct way around
Distorted output
Reduce LINE 1 and LINE 2 level controls, increasing amp level to compensate
Reduce level of source signal(s) connected to LINE 1 and LINE 2 inputs
Ensure correct line level is selected on amplifier/active speaker inputs
Output is very low level
Ensure input source is line level (0.775Vrms)
Increase LINE 1 and/or LINE 2 level controls,
Increase signal source level
Note: for further troubleshooting, refer equipment to qualified service personnel for testing
© Citronic 1201


Product specificaties

Merk: Citronic
Categorie: Mengpaneel
Model: Z5M

Heb je hulp nodig?

Als je hulp nodig hebt met Citronic Z5M stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Mengpaneel Citronic

Handleiding Mengpaneel

Nieuwste handleidingen voor Mengpaneel

Ashly

Ashly AQM 1208 Handleiding

15 December 2024
Yamaha

Yamaha MB02R96 Handleiding

14 December 2024
Yamaha

Yamaha Rio1608-D Handleiding

13 December 2024
Yamaha

Yamaha Ri8-D Handleiding

13 December 2024
Yamaha

Yamaha RSio64-D Handleiding

13 December 2024
Phonic

Phonic AM8GE Handleiding

11 December 2024
Phonic

Phonic AM642DP Handleiding

11 December 2024
Phonic

Phonic AM440 Handleiding

11 December 2024