Citronic CM10-LIVE Handleiding

Citronic Mengpaneel CM10-LIVE

Lees hieronder de 📖 handleiding in het Nederlandse voor Citronic CM10-LIVE (5 pagina's) in de categorie Mengpaneel. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

CM-series compact mixing consoles

CM4-LIVE (170.800) CM4-STUDIO (170.810)

CM6-LIVE (170.801)

CM8-LIVE (170.802) CM8-STUDIO (170.812)

CM10-LIVE (170.803)

User Manual

Features:

 4 “ ”LIVE models with USB/SD player and delay eﬀect

 2 “ ”STUDIO models with audio input/output USB

 3-band EQ per channel

 +48V phantom power

 8 and 10 channel models are rack-mountable

 Channel inserts for mono inputs

 AUX feed from each channel

www.citronic.com

Introduction:

Thank you for choos a Citronic CM series mixer. This product has been designed to oﬀer reliable, high quality mixing for ing

stage and/or studio applications with unfailing consistency. In order to gain the best results from this equipment and avoid

damage through misuse, please read and follow these instructions and retain for future reference.

Warning:

To prevent the risk of ﬁre or electric shock, do not expose any of the components to rain or moisture.

If liquids are spilled on the surface, stop using immediately, allow unit to dry out and have checked by qualiﬁed personnel before

further use.

Avoid impact, extreme pressure or heavy vibration to the unit.

There are no user serviceable parts inside the mixer refer all servicing to qualiﬁed service personnel. –

Safety

 Check that the supplied adapter and connectors are in good condition and the mains supply voltage is correct.

 Ensure signal leads are of good condition without shorted connections (especially when using phantom power)

 Do not use the USB connector as a general purpose power source or charger.

 Do not allow any foreign particles to enter the console through connectors or control apertures

Placement

 Keep out of direct sunlight and away from heat sources.

 Keep away from damp or dusty environments.

 When rack-mounting, (CM8-LIVE, CM10-LIVE, CM8-STUDIO) use rack ears supplied, securing ﬁrmly.

 Ensure adequate access to controls and connections, including USB/SD player on rear panel (CM-LIVE)

Cleaning

 Use a soft cloth with a neutral detergent to clean the casing as required

 Use a soft brush to clear debris from the control surface

 Do not use strong solvents for cleaning the unit.

Control Panel

1. XLR MIC input

2. Channel INSERT TRS 6.3mm jack –

3. LINE input 6.3mm jack

4. Channel GAIN rotary

5. PAN (L-R balance) control

6. 3-band EQ (HIGH/MID/LOW) controls

7. Channel AUX output level

8. EFF rotary internal delay or EFFECT out (CM-LIVE) –

9. Channel volume fader

10. Channel PEAK LED

11. +48V phantom power switch

12. Stereo channel line input 2 x 6.3mm jack –

13. Stereo channel line input 2 x RCA –

14. REC output – record out on 2 x RCA

15. AUX output 6.3mm jack –

16. EFFECT output 6.3mm jack (overrides Delay eect) –

17. USB/SD player display (CM-LIVE)

18. PHONES output stereo 6.3mm jack –

19. USB/SD player transport controls (CM-LIVE)

20. Power LED

21. VU and CLIP LEDs for L + R output

22. DELAY and REPEAT controls (CM-LIVE)

23. PHONES output level

24. AUX output level

25. EFFECT output level (CM-LIVE)

26. MAIN fader master volume control –

Rear Panel

Connection

Before connecting to ampliﬁer or other equipment, turn down all volume controls to avoid loud noises which may

cause damage to other equipment. Always switch ampliﬁer power on last in line with volume levels down.

Using good quality 6.3mm jack leads (balanced or unbalanced), connect L + R outputs from the mixer to the

ampliﬁer, recorder or whichever equipment is to receive the main mix output.

If phantom power is to be used, press the +48V switch in. “ ”

Connect microphones, DI boxes other balanced low impedance audio inputs to the mono channels using a and

quality XLR lead.

Connect high impedance and line level signals to the mono inputs using a 6.3mm jack lead .

For the stereo channel, connect left and right line level signals via 6.3mm jack or RCA leads (unbalanced).

Channel inserts may be connected to individual processing equipment like EQ or compressors. These connections

completely interrupt the signal ﬂow and divert to the external processor before returning to the channel for volume

adjustment via the channel fader. This requires a stereo to 2 x mono jack lead the 2 mono ends are send and –

return connections, the stereo connection is wired as per below.

Recording equipment can be connected via the REC outputs using a twin RCA lead and the 6.3mm jack AUX “ ”

output can be connected monitoring or external processing equipment if required. Individual levels can be to

adjusted to the AUX output via the individual channel AUX controls.

For CM-LIVE models, if the internal delay eﬀect is not quired, a send can be connected from the EFFECT jack re “ ”

output to and external eﬀect unit, whereby the EFF channel controls act as individual level controls to the EFFECT

output (same as for AUX output)

With all faders down, connect the supplied AC adapter to the 12Vac input and to the mains supply (ensure correct

supply voltage) the power LED will illuminate (if phantom power is selected, this LED should light also) –

Checking

Test each channel s gain level by making the loudest expected sound into it and increasing the GAIN control until ’

the red PEAK LED starts to light. Then back the GAIN oﬀ slightly until the PEAK LED hardly lights at all.

Test the main mix output by increasing the MAIN fader and selected channel faders whilst making sound through

the channel(s) the L + R output LED ladders should begin to show the output as it varies up and down. –

Connecting a pair of headphones to the PHONES stereo 6.3mm jack is a good way of checking the mix output,

remembering to gradually increase the PHONES level control.

Turn down all faders and then switch power on to connected equipment (ampliﬁer last in line) and increase volume

levels. Gradually increase MAIN and channel faders again and the sound should be heard through the speakers or

be indicated on the recording equipment.

27. 12Vac power input (adapter supplied)

28. USB type B output/monitoring input (CM-STUDIO only) –

29. L + R main output (on top control panel for CM-STUDIO)

30. SD card slot (CM-LIVE only)

31. USB type A input (CM-LIVE only)

Product specificaties

Merk:	Citronic
Categorie:	Mengpaneel
Model:	CM10-LIVE

Heb je hulp nodig?

Als je hulp nodig hebt met Citronic CM10-LIVE stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Mengpaneel Citronic

Citronic U-Pad 170.876UK Handleiding

8 Juli 2023

Citronic PRO-2 MKII Handleiding

5 Juli 2023

Citronic CDM8:4 mkV Handleiding

5 Juli 2023

Citronic CDM10:4 mk5 Handleiding

4 Juli 2023

Citronic CM4-STUDIO Handleiding

3 Juli 2023

Citronic CSM-6 Handleiding

2 Juli 2023

Citronic CM10-LIVE Handleiding

2 Juli 2023

Citronic Z5M Handleiding

30 Juni 2023

Citronic CSM-8 Handleiding

29 Juni 2023

Citronic CSM-4 Handleiding

28 Juni 2023

Handleiding Mengpaneel

Nieuwste handleidingen voor Mengpaneel

NutriBullet Ultra 1200 Handleiding

16 November 2024

Mackie ProFX12 Handleiding

15 November 2024

Solid State Logic SSL UF1 Handleiding

15 November 2024

Yamaha IM8-32 Handleiding

14 November 2024

Yamaha IM8-40 Handleiding

14 November 2024

Yamaha DCU5D Handleiding

14 November 2024

Yamaha SP02R96 Handleiding

14 November 2024

Yamaha MG166C-USB Handleiding

13 November 2024

RCF L-PAD 12C Handleiding

5 November 2024

RCF L-PAD 10C Handleiding

5 November 2024