Caple LEV3 Handleiding

Caple Kraan LEV3

Lees hieronder de 📖 handleiding in het Nederlandse voor Caple LEV3 (115 pagina's) in de categorie Kraan. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/115
Customer care helpline: 0117 938 1900
www.caple.co.uk
CH ROME AND BRUS HE D NICKE L TAP C A RE ,
INSTA LL ATI O N A ND GU A RA NTEE INF ORMATI ON
MODE L CODE S: LE V 3 /CH & L EV 3/ B N
2 INS TALLATION GUI DE LEV3/ CH + LEV3 /BN Please keep this instruction manual for future reference
INS TALL ATION GU I DE
Thank you for purchasing your Caple tap.
These taps have been manufactured and inspected to exacting standards and are guaranteed to give years of trouble
free operation providing our care and installation guidelines have been followed.
NOTE: Please see back page for installation instructions
24
-
4Please keep this instruction manual for future reference
GUAR ANTEE
-Your Caple tap is guaranteed for 5 years.
- Should you have any defects as detailed above during the appropriate guarantee period we guarantee to repair or replace
the defective products or parts, or, at our option refund the purchase price assuming we were advised immediately of any
claim in writing.
- It is important that you keep a proof of purchase (such as your receipt) to facilitate your guarantee.
INS TALL ATI ON INS TRUC TI ONS
- Turn the spout and body so the tap is facing forwards, the
screw on the spout indicates the rear of the body. The hot
water connection should be on the left of the tap.
-Ensurethehotandcoldpipesarethoroughlyushedtoremove
any debris.
- A 35mm hole is required in either the sink or worktop.
-Thexingboltmustbescrewedintothetapbase,ensuringthe
threads of the bolt are not damaged in the process.
-Passthenylonwasheroverthexingboltushtothebottom
of the tap base, then pass the bolt through the sink or worktop
(ensuring the nylon washer remains directly under the tap
base).
- Pass the rubber washer and then the metal washer (on the
undersideofthesink/worktop)overthexingboltandxusing
thexingnut.
-Screwtheexi-tailpipesintothebaseofthetap,ensuringthe
pipesthreadsarenotdamagedintheprocess.Iftheexi-tails
are already inserted into the tap base, please ensure these are
screwed in tightly to prevent any leaks.
-Finallyconnecttheexi-tailpipestothehotandcoldsupplies
ensuring they are connected to the correct supplies.
C AR E OF YOU R TAP S
- Only clean your taps with soap or mild liquid detergent and
clean water then dry using a soft cloth
- Do not use chemical cleaners, or bleach based
solutionstocleanyourtap,contactcouldaffectthenishof
your tap.
- Do not use abrasive cleaners, liquids, powders or pads. These
willdamagethenishofyourtapandvoidtheguarantee.
- Provided all of the above points are adhered to the surface
nishofyourCapleTapisguaranteedfor5years.
PRE I N STA LL ATIO N C HEC KS
- The temperature of the hot water supply must not
exceed 70°C.
- Water pressure requirements: minimum required pressure
varies dependent on model, maximum pressure 5 bar.
-Alwaysseekadvicefromaqualiedinstallertoensureyour
installation and water supply to your taps comply with the
water regulation (WRAS) requirements and good plumbing
practice.
- It is good practice to ensure that both hot and cold water
supplies to your tap are of an equal pressure to provide a
consistentow.Ifsuppliesarenotofequalpressurethena
nonreturnvalveshouldbettedonthehotinlet.
- Supplies of water should be from a common source (mains or
tank fed).
- We recommend that a service valve is installed in the
supply lines to the tap to enable water isolation if required.
POS T I N STAL LATION PO I NT S
- We suggest when connecting screw connections that PTFE tape
is used before the joints are fully tightened.
- Before use correctly check the installation for leaks, and
turnthehotandcoldwaterontothoroughlyushany
small particles that may have been dislodged during the tap
installation.
THES E INSTRUCTIONS ARE INTENDED AS A GUIDE,
IF IN ANY DOUBT ENSURE YOU SEEK ADVICE
FROM A CERTIFIED PLUMBER.
TE RMS AN D C ONDI TI ONS
- Guarantee conditions are only valid if the Care guidelines listed above are followed.
- Our obligation under the guarantee is to the original purchaser, and may not be transferred.
- The guarantee is valid for UK domestic installations only and relates to defects in manufacture, materials and
workmanship only.
- Issues that arise due to normal wear and tear (for example valves, discs or washers), poor installation,
improper use or accidental damage are not covered by the Caple guarantee. Spare parts can be purchased
from our Customer care helpline 0117 938 1900.
-Noliabilityisacceptedforconsequentialdamagetootherhouseholdxtures,ttingsorfurnishingsrelating
toanyclaim-evenifattachedtotheproduct.
- If it is more economically viable a replacement tap will be supplied, this tap might vary from the original
design should range changes of occurred since the initial supply.
- We reserve the right to inspect any tap before committing to support under the guarantee conditions.
INSTALLATION GUIDE LEV3/CH + LEV3/BN


Product specificaties

Merk: Caple
Categorie: Kraan
Model: LEV3

Heb je hulp nodig?

Als je hulp nodig hebt met Caple LEV3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Kraan Caple

Handleiding Kraan

Nieuwste handleidingen voor Kraan