Caple ANT4/CH Handleiding

Caple Kraan ANT4/CH

Lees hieronder de 📖 handleiding in het Nederlandse voor Caple ANT4/CH (3 pagina's) in de categorie Kraan. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

Customer care helpline: 0117 938 1900

www.caple.co.uk

CH ROM E AN D BRUS HED NIC KE L TAP

C AR E , INS TALL ATIO N AN D GUAR A NT E E IN FOR MATION

MO DE L CO DE : A NT4 / CH & AN T4 / B N

2 INSTALLATION GUIDE ANT4/CH & ANT4/ BN Please keep this instruction manual for future reference

I NS TA L L ATI O N G U I DE

Thank you for purchasing your Caple tap.

These taps have been manufactured and inspected to exacting standards and are guaranteed to give years of trouble

free operation providing our care and installation guidelin es have been followed.

NOTE: Please see back page for installation instructions

4 INSTALLATION GU IDE A NT4/CH & ANT4/ BN Please keep this instruction manual for future reference

INS TAL L ATIO N I N S TR UC T I O N S

- Turn the spout and body so the tap is facing forwards, the

screw on the spout indicates the rear of the body. The hot water

connection should be on the left of the tap.

- Ensure the hot and cold pipes are thoroughly ﬂushed to remove

any debris.

- A 35mm hole is required in either the sink or worktop.

- The ﬁxing bolt must be screwed into the tap base, ensuring the

threads of the bolt are not damaged in the process.

- Pass the nylon washer over the ﬁxing bolt ﬂush to the bottom

of the tap base, then pass the bolt through the sink or worktop

(ensuring the nylon washer remains directly under the tap base).

- Pass the rubber washer and then the metal washer (on the

underside of the sink/worktop) over the ﬁxing bolt and ﬁx using

the ﬁxing nut.

- Screw the ﬂexi-tail pipes into the base of the tap, ensuring the

pipes threads are not damaged in the process. If the ﬂexi-tails

are already inserted into the tap base, please ensure these are

screwed in tightly to prevent any leaks.

- Finally connect the ﬂexi-tail pipes to the hot and cold supplies

ensuring they are connected to the correct supplies.

C ARE O F YO U R TAP S

- Only clean your taps with soap or mild liquid detergent and

clean water then dry using a soft cloth

- Do not use chemical cleaners, or bleach based solutions to clean

your tap, contact could affect the ﬁnish of your tap.

- Do not use abrasive cleaners, liquids, powders or pads. These

will damage the ﬁnish of your tap and void the guarantee.

- Provided all of the above points are adhered to the surface ﬁnish

of your Caple Tap is guaranteed for 5 years.

PR E IN S TAL L ATI O N C H EC K S

- The temperature of the hot water supply must not exceed 70°C.

- Water pressure requirements: minimum required pressure varies

dependent on model, maximum pressure 5 bar.

- Always seek advice from a qualiﬁed installer to ensure your

installation and water supply to your taps comply with the water

regulation (WRAS) requirements and good plumbing practice.

- It is good practice to ensure that both hot and cold water

supplies to your tap are of an equal pressure to provide a

consistent ﬂow. If supplies are not of equal pressure then

a non return valve should be ﬁtted on the hot inlet.

- Supplies of water should be from a common source (mains or

tank fed).

- We recommend that a service valve is installed in

the supply lines to the tap to enable water isolation

if required.

POST I N S TAL L ATIO N P O I N TS

- We suggest when connecting screw connections that PTFE tape

is used before the joints are fully tightened.

- Before use correctly check the installation for leaks, and turn the

hot and cold water on to thoroughly ﬂush any small particles

that may have been dislodged during the tap installation.

- THESE INSTRUCTIONS ARE INTENDED AS A GUIDE,

IF IN ANY DOUBT ENSURE YOU SEEK ADVICE FROM A

CERTIFIED PLUMBER.

GU A RA N TEE

-Your Caple tap is guaranteed for 5 years.

- Should you have any defects as detailed above during the appropriate guarantee period we guarantee to repair or replace the

defective products or parts, or, at our option refund the purchase price assuming we were advised immediately of any claim

in writing.

-It is important that you keep a proof of purchase (such as your receipt) to facilitate your guarantee.

TE R MS AND CO NDI T I O N S

-Guarantee conditions are only valid if the Care guidelines listed above are followed.

-Our obligation under the guarantee is to the original purchaser, and may not be transferred.

- The guarantee is valid for UK domestic installations only and relates to defects in manufacture, materials and workmanship only.

- Issues that arise due to normal wear and tear (for example valves, discs or washers), poor installation, improper use or accidental

damage are not covered by the Caple guarantee. Spare parts can be purchased from our Customer care helpline 0117 938 1900.

- No liability is accepted for consequential damage to other household ﬁxtures, ﬁttings or furnishings relating to any claim – even if

attached to the product.

- If it is more economically viable a replacement tap will be supplied, this tap might vary from the original design should range changes

of occurred since the initial supply.

-We reserve the right to inspect any tap before committing to support under the guarantee conditions.

Product specificaties

Merk:	Caple
Categorie:	Kraan
Model:	ANT4/CH
Kleur van het product:	Chroom
Hoogte (max):	204 mm
Certificering:	CE
Draaibaar:	Ja
Draaihoek:	360 °
Uitlooptype:	Standaard
Materiaal kraan:	Staal
Aantal kranen/grepen:	Dubbel
Buisvorm:	Type J
Type ventiel:	Kogelventiel
Diameter mousseur:	42 mm