Apc Back- 300 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Apc Back- 300 (2 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
APC Back-UPS® 300, 500, 650 User’s Manual 990-2004E Revision 7 12/99
Inspect
Inspect the UPS and its contents on receipt:
• User’s Manual • UPS • Cord straps (2)
• Telephone cable • Warranty card
• APC Solutions magazine
• Equipment Protection policy
500 and 650 VA models:
• PowerChute® plus software CD
• Interface cable
• Software Install Sheet
The packaging is recyclable, save it for re-use or
dispose of it properly. Please fill out the warranty
registration card to obtain warranty coverage.
Place
Locate the UPS in a protected area that is free of
excessive dust and has adequate air flow. Do not
operate the UPS where the temperature and
humidity is outside specifications.
Connect UPS to power
Connect the battery
Refer to "Battery replacement procedure"- pg. 2
Charge the battery
The UPS battery charges whenever it is connected to
utility power and typically requires less than five hours
to charge fully. UPS capacity is reduced until the
battery is fully charged.
Check site wiring fault
indicator (rear panel-top)
A lit indicator means that a shock hazard exists due to
faulty building wiring , that should be corrected by a
qualified electrician.
If the building wiring fault indicator is lit, one of the
following conditions exist:
• Open or high resistance ground
• Hot and neutral polarity reversal
• Overloaded neutral circuit
Note: Improper building wiring will not prevent the
UPS from operating but will limit it's protection
capability. Faulty building wiring could result in
equipment damage that is not covered by APC. Please
refer to APC's Equipment Protection Policy for details.
Connect phone cables to
surge protection (optional)
Socket Location:
Rear panel of 500 and 650 VA models only.
Surge protection is provided for one phone line when
it is connected as shown below:
Switch "On" and test the UPS
Press the upper portion of the Power 1/0 switch and
then switch "On" the equipment connected to the UPS.
The Power 1/0 switch should be lit. Utility power is
supplied to the equipment.
Perform a simulated utility blackout test to confirm the
UPS unit can switch from utility power to battery
power and back again, without affecting equipment
powered by the UPS.
Connected equipment must be "On".
Continued
Connect equipment
Cord Straps: Straps are provided to keep cords from
tangling and taking up too much space.
Battery Back-Up Outlets:
•Surge protection when utility power is used
•Battery power and surge protection when utility
voltage is outside acceptable limits.
Data-sensitive equipment such as a computer, monitor,
or external drive are connected to these outlets.
Accessory Surge Protection Outlets (500 and 650
VA models only): These outlets are for equipment that
need surge protection but do not need power during a
utility outage (like an inkjet printer or a scanner).
BlockSafeâ„¢ Outlets (500 and 650 VA models only):
Corded sockets are provided which accept "block type"
plugs without covering other outlets. Some printers and
external disk drives have block type plugs that look
similar to the one below.
Caution: Do not connect a surge
suppressor or laser printer to the UPS.
These devices may overload the UPS.
Continued
Start the test by either:
•Unplugging the UPS power cord, or
•Pressing and holding the "Test" portion of the Test/
Alarm Disable switch (500 and 650 VA models
only).
1. The UPS will then beep once every five seconds (or
continuously) to remind you that your equipment is
powered by a limited capacity power source.
2. Restore power to the UPS by releasing the Test
switch or by reconnecting the UPS power cord.
If the equipment operation was undisturbed throughout
the testing, the system is operating properly.
Connect computer interface cable (optional)
Socket Location:
Rear panel of UPS
Note: 300 VA model users must purchase software and
cable separately. Call APC at the number listed at the
bottom of Page 2, and ask for software kit AP9015.
Connect the interface cable to the computer interface
port on the rear panel of the UPS. Connect the other
cable end to an unused serial port socket on the
computer and install the PowerChute® plus software
(see software documentation for detailed instructions).
UPS Controls
Power 1/0 Switch
The Power 1/0 Switch controls
power to the UPS.
Lamp: The lamp in the Power 1/0 Switch is lit
whenever normal utility voltages are present at the
power sockets.
1The UPS operates and all connected devices are
powered.
0The UPS is de-energized and all devices connected
to battery backup outlets are unpowered
All devices connected to battery back-up outlets can
be switched "On" or "Off" using this switch, if each
device's power switch is left in the "On" position.
Note: Accessory surge protected outlets are
unaffected by this switch - they remain powered as
long as utility power is available.
Test/Alarm Disable Switch
Switch Location: Front panel of
500 and 650 VA models only.
The battery run time can be checked by pressing and
holding the "Test" switch and waiting to see how long
the UPS provides power to the equipment before the
low battery warning is sounded.
Test
Press the "Test" portion of the Test/Alarm Disable
Switch to simulate a power outage - the UPS battery
supplies power to the equipment
Alarm Disable
The UPS will emit a beep once every five seconds
during a utility power outage, unless the alarm is
disabled by pressing this side of the switch. The UPS
low battery warning (a loud continuous tone) will still
sound in the event of an extended utility outage.
Specifications RunTime (minutes) vs. Power Demand
egatloVtupnIelbatpeccA esahPelgniS,caV051-0
egatloVrefsnarT )rewoltesebyam(caV301
egatloVtuptuO caV121-901
noitcetorPtnerruCrevOtupnI rekaerbtiucricelbatteseR
)enilno(stimiLycneuqerF )gnisnesotua(zH36-75
emiTrefsnarT
)emitesnopsertuokcalb( sm8
daoLmumixaM
AV003 W081-
AV005 W033-
AV056 W004-
egatloVtuptuOyrettab-nO caV511
ycneuqerFyrettab-nO tuonworbgnirudytilituotdezinorhcnyssselnuzH26-85
epahsevaWyrettab-nO evaw-enisdeppetS
noitcetorPtnerruCrevOtuptuO nonwodtuhsgnihctal,detcetorptiucric-trohsdnatnerrucrevO
daolrevo
epyTyrettaB dica-daeldelaes,eerfecnanetniam,foorpllipS
efiLyrettaBlacipyT dnaselcycegrahcsidforebmunnognidneped,sraey6ot3
erutarepmettneibma
emiTegrahceRlacipyT egrahcsidlatotmorfsruoh01ot5
erutarepmeTgnitarepO )C°04ot0(F°401ot23
erutarepmeTegarotS )C°54ot51-(F°311ot5
evitaleRegarotSdnagnitarepO
ytidimuH gnisnednoc-non,%59ot0
noitavelEgnitarepO )m000,3+ot0(tf000,01+ot0
noitavelEegarotS )m000,51+ot0(tf000,05+ot0
)m1(tf3taesioNelbiduA ABd04<
)DxWxH(eziS AV005,AV003 )mc3.33x6.8x1.51("1.31x"4.3x"0.6:
:AV056 )mc1.63x9.11x8.61("2.41x"7.4x"6.6
thgieW
AV003 )gk0.6(bl1.31
AV005 )gk0.7(bl4.51
AV056 )gk5.01(bl0.32
thgieWgnippihS
AV003 )gk1.7(bl7.51
AV005 )gk2.8(bl0.81
AV056 )gk0.21(bl5.62
snoitacifitreCdnagnitsiL 86trapdna51trapCCF,1.701ASC,8771LU
noitacifireVIME deifitrecBssalCCCF
ytinummIcitengamortcelE IIIlevel5-108dna,VIlevel4-108,3-108,2-108CEI
noitpircseDmetsyS dnameD
)sttaW(
SPU-kcaB
003
SPU-kcaB
005
SPU-kcaB
056
684potkseD
rotinoM"51ro"41/w 501 61 22 73
muitnePrewoTiniM/potkseD
rotinoM"51ro41/w 011 41 02 43
muitnePrewoTiniM/potkseD
rotinoM"71/w 031 01 71 62
orPmuitneP/IImuitnePrewoTiniM/potkseD
rotinoM"51ro41/w 031 01 71 62
orPmuitneP/IImuitnePrewoT
rotinoM"51ro"41/w 051 8 41 12
muitnePrewoT
rotinoM"71/w 051 8 41 12
orPmuitneP/IImuitnePrewoTiniM/potkseD
rotinoM"71/w 051 8 41 12
muitnePrewoTiniM/potkseD
rotinoM"12/w 071 6 21 71
orPmuitneP/IImuitnePrewoT
rotinoM"71/w 071 6 21 71
6KrewotiniM/potkseD
rotinoM"12/w 081 6 01 51
muitnePrewoT
rotinoM"12/w 091 - 9 41
orPmuitneP/IImuitnePrewoTiniM/potkseD
rotinoM"12/w 091 - 9 41
orPmuitneP/IImuitnePrewoT
rotinoM"12/w 012 - 7 11
yamerutarepmetgnitarepodetaveledna,esuevissecxe,egayrettaB.etamixorppaeraseulavesehT:etoN
.gnizis/moc.cpa.www//:ptthtadnuofebnacnoitamrofnieroM.emitnurSPUesaercedrehtruf
5 hours
Phone Line
Modem/Fax/Phone
System
Option Switches
A set of 4 switches, located on the rear panel, can be used to change how the UPS operates. For typical
applications, all switches are in the down position as shown below.
Switch 1
noitisoPhctiwS tluseR
gnitteSlamroN ehtnehwsdnocesevifyreveecnospeebSPUehT:
.stimilelbatpeccaedistuonellafsahegatlovytilitu
eruliafytilituelbiduaSPUeht,noitisop"nO"ehtottessi1#hctiwsfI
rewopfeirbnehwtneinevnocsierutaefsihT.detaefedsimrala
.gniyonnasemocebmralaehtdnanommocerasnoitpurretni
Regardless of the position of switch 1, the UPS will sound a loud continuous tone during low battery
conditions.
Switches #2 and #3
Switches #2 and #3 set the utility voltage value (transfer voltage) at which the UPS will switch to battery
power. If you know that your equipment will operate properly at any of the voltages less than 103 V shown in
the table, you can change to the corresponding switch positions. Changing the transfer voltage is desirable
when frequent line voltage excursions or line voltage distortion cause the UPS to use battery power too often.
noitisoPhctiwS egatloVrefsnarT
CAV301
gnitteSlamroN
CAV89
CAV39
CAV88
Switch #4 (500 and 650 VA models only)
noitisoPhctiwS tluseR
:gnitteSlamroN dednetxenagnirudnwodtuhsotroirpsetunimowT
etavitcadnagninrawyrettabwolehtdnuoslliwSPUeht,egatuorewop
.tropecafretniretupmocehttalangisyrettabwoleht
setunimevifdeussisigninrawehttpecxe"lamroN"saroivahebemaS
setunimowtnahteromeriuqeruoyfignittessihtesU.nwodtuhserofeb
.snoitarepoesolcdnaselifevasot
Troubleshooting
Use the table below to solve minor UPS installation problems. Consult the APC web site or contact APC
Technical Support Staff for assistance with complex UPS problems.
esuaCelbissoP erudecorP
sdnocesevifyrevetuobaspeebSPU
.egatuorewopytilitU eB.tnempiuqeruoygnitcetorpsiSPUehT.enoN
gnitarepoehtdnasnoitacilppatixeylreporpotderaperp
SPUehterofebmetsyseht"ffO"rewopnehtdna,metsys
.degrahcsidylsuoiressi
yllanoisaccospeebSPU
roegatuoytilituyraropmeT
.ecnabrutsid
.tnempiuqeruoygnitcetorpsiSPUehT.enoN
stsixeegatlovytilitulamronhguohtlayrettab-nosetarepoSPU
."deppirt"rekaerbtiucrictupniSPU ybdnamedrewoptnempiuqeecudeR
.SPUehtmorftnempiuqegniggulpnu
fokcabno(rekaerbtiucricehtteseR
.nikcabregnulpgnisserpyb)SPU
.derruccosahtuonworbA noitpognignahcybderewolebnacegatlovrefsnartehT
uoyfI:etoN.)noitcessuoiverpees(3dna2sehctiws
llaerusekamegatlovrefsnartehtrewolotediced
etarepolliwsteltuopukcabyrettabotdetcennocsecived
.egatlovytiliturewolsihttaylreporp
"nO"nruttonlliwSPU
rewopCAotdetcennoctonsiSPU
.ylppus
rewopehtotSPUehtmorfelbacrewopehttahtkcehC
.detcennocylerucessiylppus
."deppirt"rekaerbtiucricSPU gniggulpnuybSPUehtnodnamedrewopehtecudeR
.rekaerbtiucricehtteserdnatnempiuqe
.egatlovytilituonrowolyreV SPUehtotylppusrewopCAehtkcehC
yrevsipmalehtfI.pmalelbatahtiw
.dekcehcegatlovytilituehtevah,mid
.ylreporpdetcennoctonsiyrettaB yrettaBehttlusnoC.snoitcennocyrettabehtkcehC
ehtsseccaotwohswohstahterudecorPtnemecalpeR
.yrettab
emitpukcabdetcepxeedivorptonseodSPU
.dedaolrevosiSPUehT .sretnirpsahcus,tnempiuqelaitnesse-nongulpnU
oteudkaewsiyrettabSPUehT
fodneehtraensiroegatuotnecer
.efilecivressti
htiwsesaercedyticapacyrettaB.yrettabehtegrahC
tadetareponehwrosegatuorewop)gnolro(tneuqerf
stifodneehtraensiyrettabehtfI.serutarepmetdetavele
.yrettabehtgnicalperredisnoc,efilecivres
Warranty
Customers may return their defective unit to APC for replacement or repair during the standard 2 year
warranty period. APC's standard procedure will be to replace the original unit with a factory-reconditioned
unit. Customers who must have the original unit back due to assigned asset tags and set depreciation
schedules must declare such a need at first contact with APC Customer Service. APC will ship out the
replacement unit once the defective unit has been received by the repair department. The customer pays for
the shipping to APC, APC covers ground freight transportation costs back to the customer.
Order replacement battery
The table below shows the APC part numbers for APC Back-UPS replacement battery cartridges (RBCs).
Replacements can be ordered from local retailers, APC, or the APC website at
http://www.apc.com.
sledomAV005dna003 2CBR
ledomAV056 3CBR
Battery replacement procedure
This procedure requires a coin or screwdriver.
Note: Please read the cautions in the APC Safety Information Guide first!
Battery replacement is a safe procedure, isolated from electrical hazards. You may leave the UPS connected to
utility power and your equipment connected and "On" during this procedure.
Note: Once the battery is disconnected, the loads are not protected from power outages.
.1 swercsowtehtevomeR.edistfelstinoSPUehtyaL
.roodehtnepodnaroodyrettabehtnognidloh
:etoN ylthgilsroodyrettabehtllupotyrassecenebyamtI
nepootredronitinuehtfotnorfehtdrawotrodrawtuo
.yllufroodeht
.2 llupyltnegdnayrettabehtotdehcattabatetihwehtpsarG
.tuoyrettabeht
.3 ehtotyrettabehtgnitcennocseriwowtehttcennocsiD
gnillupelihwmehtgnilggiwybseriwehtnesooL.SPU
.rotcennocyrettabehtmorfkcabthgiarts
.4 .dloehtfoecalpniyrettabwenehttcennoC
:etoN lamronerasnoitcennocyrettabehttaskrapsllamS
.noitcennocgnirud
.5 diovaylluferaC.SPUehtniyrettabwenehttresnI
.seriwehtgnihcnip
.6 ehtecalperdnaroodtnemtrapmocyrettabehtesolC
.swercs
.7 naotyrettabehtrevileD.delcycerebtsumseirettabtnepS
nireilppusehtottipihsroytilicafgnilcyceretairporppa
yrettabwenehteeS.lairetamgnikcaps'yrettabweneht
.noitamrofnieromrofsnoitcurtsni
Storage
Before storing, charge the UPS for at least 10 hours. Store the UPS covered and upright in a cool, dry
location.
Long term storage
erutarepmeTegarotS ycneuqerFegrahceR noitaruDgnigrahC
)Co03ot51-(Fo68ot5 shtnoM6yrevE sruoH01
)Co54ot03(Fo311ot68 shtnoM3yrevE sruoH01
Service
Note: If the UPS requires service, do not return it to the dealer! The following steps should be taken.
1. Consult the Troubleshooting section to eliminate common problems.
2. Verify that no circuit breakers are tripped. A tripped circuit breaker is the most common UPS problem!
3. If the problem persists, consult the APC Worldwide Web site (www.apc.com) or call customer service.
•Record the model number of the UPS, the serial number, and the date purchased. Be prepared to
troubleshoot the problem over the telephone with a technician If this is not successful, the technician
will issue a Return Merchandise Authorization Number (RMA#) and a shipping address.
•If the UPS is under warranty, repairs are free. If not, there is a repair charge.
4. Pack the UPS in its original packaging. If the original packing is not available, ask customer service about
obtaining a new set. Pack the UPS properly to avoid damage in transit.
Note: Never use Styrofoamâ„¢ beads for packaging. Damage sustained in transit is not covered
under warranty (insuring the package for full value is recommended).
5. Write the RMA# on the outside of the package.
6. Return the UPS by insured, prepaid carrier to the address given to you by customer service.
APC contact information
……........………adanaC/ASU
..……........…………ocixeM
…….........……………lizarB
….………........……ediwdlroW
2724-008-008-1
5520-292,3520-292
1-27-21-0080
5375-987-104-1
tenretnI
moc.cpa.www//:ptth
liaM-E
moc.cpa@hcetcpa
Product specificaties
| Merk: | Apc |
| Categorie: | UPS |
| Model: | Back- 300 |
Heb je hulp nodig?
Als je hulp nodig hebt met Apc Back- 300 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding UPS Apc
29 Maart 2025
29 Maart 2025
29 Maart 2025
29 Maart 2025
29 Maart 2025
28 Maart 2025
27 Maart 2025
27 Maart 2025
27 Maart 2025
27 Maart 2025
Handleiding UPS
- UPS HP
- UPS IKEA
- UPS AEG
- UPS Siemens
- UPS Dell
- UPS Digitus
- UPS Eaton
- UPS Emerson
- UPS Furman
- UPS Gembird
- UPS Gys
- UPS Hikvision
- UPS Lenovo
- UPS LevelOne
- UPS Riello
- UPS Schneider
- UPS Teltonika
- UPS Voltcraft
- UPS Jung
- UPS Steren
- UPS Conceptronic
- UPS Tripp Lite
- UPS Approx
- UPS Block
- UPS LC-Power
- UPS Energenie
- UPS CyberPower
- UPS Adj
- UPS East
- UPS Xtreme
- UPS Equip
- UPS Liebert
- UPS Avocent
- UPS Minute Man
- UPS Minuteman
- UPS Maruson
- UPS V7
- UPS Phoenix Contact
- UPS Puls Dimension
- UPS Vanson
- UPS Salicru
- UPS SurgeX
- UPS Murr Elektronik
- UPS Altronix
- UPS Ditek
- UPS Bxterra
- UPS Middle Atlantic
- UPS FSP
- UPS Atlantis Land
- UPS PowerWalker
- UPS FSP/Fortron
- UPS Online USV
Nieuwste handleidingen voor UPS
29 Maart 2025
4 Maart 2025
4 Maart 2025
30 Januari 2025
28 Januari 2025
28 Januari 2025
28 Januari 2025
28 Januari 2025
28 Januari 2025
27 Januari 2025