Alecto DVM-671 Handleiding

Alecto Babyfoon DVM-671

Lees hieronder de 📖 handleiding in het Nederlandse voor Alecto DVM-671 (2 pagina's) in de categorie Babyfoon. Deze handleiding was nuttig voor 110 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

INTRODUCTION

The Alecto DVM-67 is a wireless audio/video baby monitor,

suitable for private use indoors.

You can either watch and listen continuously or you can have

the baby monitor switch on automatically as soon as your

baby starts crying.

The Alecto DVM-67 meets all essential requirements and

other provisions as described in the European Directive

1999/5/EC.

The declaration of conformity is available

on the website www.alecto.nl

Use of this equipment is allowed in all countries of the EU. In

France, Italy, Russia and Ukraine, only indoor use is allowed.

ICONS ON THE DISPLAY

upper part of the display, during normal use

indicates the reception strength:

strong reception

good reception

average reception

bad reception

receiver is searching for a camera

no camera detected

(x = 1 ~ 4) shows which camera you are viewing

‘monitoring mode’ (setup choice to view cameras one after

the other when using multiple cameras)

volume set to 0 (speaker turned off)

VOX is activated (unit switches on automatically when the

baby starts crying)

temperature display of the baby room

battery indication:

battery is empty

battery is full

animation while the bat-

tery is charging

appears when the adaptor is connected and the battery is

not or incorrectly installed

icons on the display during setup

this icon is followed by the number of registered cameras

which you can select using the and buttons

in this menu, you can set the display brightness

here you can set the sensitivity level for the VOX function

in this menu, you can turn the VOX function on or off

here you can choose to have the temperature shown in

degrees Celsius or degrees Fahrenheit

in this menu, you can register additional cameras on the

receiver

INSTALLATION

BABY UNIT:

Power:

1. Connect one of the

supplied 6V power

adaptors to the 6V

DC input of the baby

unit.

2. Insert the adapter into

a 230V wall socket.

Only use the supplied power adaptor with model number

S003IV0600060.

Wall-mounting:

Drill two holes next to each other in the

wall separated by a distance of 5.4cm

and insert plugs and screws. The head

of the screw should stick out of the wall

for several millimeters.

Slide the foot of the baby unit over the

screws and then press the baby unit a

little downwards.

Tips for placement:

• For use as a baby monitor:

place the baby unit at least

1-2 meters away from your

baby and make sure to safely

tuck away the adapter cable.

• For optimal range, it is advis-

able to set up the baby unit

as high as possible, free from large metal surfaces.

• The temperature protrudes from the rear of the baby unit.

Make sure this sensor hangs freely, unexposed to direct

sunlight and avoid heat from e.g. light bulbs.

• The baby unit is not waterproof. When using outdoors,

make sure to protect the baby unit against moisture and

sand.

PARENT UNIT:

Power supply:

The parent unit can be powered directly by the included re-

chargeable battery or via the supplied power adapter. As soon

as you connect the power adapter, it will charge the battery

allowing for mobile use of the parent unit.

Battery:

1. Open the battery com-

partment by sliding and

clicking off the battery

cover at the rear.

2. Connect the battery

plug in the battery

compartment according

to the gure below and

install the battery.

Only install

the supplied

rechargeable NiMH bat-

tery (3.6V, 900mAh).

Never connect the plug

or install the battery by

force.

3. Click the battery cover

back onto the parent

unit.

Power adapter:

1. Connect

the other

6V power

adapter to

the DC6V

input on the

side of the

parent unit.

(behind the

rubber cover

top)

2. Insert the adapter into a 230V wall socket.

Only use the supplied power adaptor with model number

S003IV0600060.

You can recharge the battery with the parent unit either

switched on or off, although charging the battery with the

parent unit switched off will take less time.

Charging:

The battery will be charged as soon as you connect the power

adapter and insert it into a 230V wall socket.

• For initial use, charge the battery for at least 15 hours,

even if the indicator shows a fully charged battery.

• The charging circuit for the battery is managed electroni-

cally and there is no risk of overcharging, this allows you

to leave the adapter connected at all times.

• In case you will not use the set for a longer period of time

(>2 months), please make sure to disconnect the adapter

from the wall socket and remove the battery from the par-

ent unit. When starting to use the set again, make sure to

properly charge the battery.

• Make sure nobody can trip or fall over the adapter cable.

You can bundle cables that are too long with tape or

cables ties available specically for this purpose.

Battery indication:

Upper part of the display: (only with the parent unit switched

on)

• : no battery installed, parent unit is powered directly

through the adaptor

• : battery is full

• : battery is nearly empty

•

: battery is charging

Middle part of the display: (only with the parent unit switched

on)

• : this symbol appears for several seconds every minute

in the last hour before the battery is exhausted.

Indicator on the parent unit:

• ashes in red: battery nearly empty

• remains red: battery is charging (turns off when the bat-

tery is full)

Lanyard:

You can attach a lanyard

or wristband at the top of

the parent unit. A lanyard or

wristband is not included.

USER MANUAL

DVM-67

PARENT UNIT:

1. visual sound indica-

tion, also displays the

volume level while

adjusting

2. power button, press

briey to turn the

display on or off,

press and hold for

2 seconds to turn the

parent unit on or off

3. battery indicator (see

also further in this

user manual)

4. power adaptor input

5. zoom in/out,

6. power indicator

7. function button:

MENU/SELECT:

to open the menu and

to conrm selections

VOL , VOL , and

: various functions,

see this user manual

8. talk-back button to-

wards the baby unit

9. built-in microphone

10. Battery compartment

11. suspending option for

wrist band

12. built-in speaker

13. foldable stand

FUNCTIONS OVERVIEW

BABY UNIT:

1. Infra-red LEDs

(for night vision)

2. indicator light,

switched off when

the baby unit is

turned off, ashes

while the baby

unit is searching

for the parent

unit, remains lit

when the baby

unit is in commu-

nication with the

parent unit

3. power adaptor

input

4. power button

5. light sensor

6. camera lens

7. Volume increase

8. PAIR button (to

pair this baby unit

with a (another)

parent unit)

9. Volume decrease

10. built-in micro-

phone

11. Built-in speaker

12. Temperature

sensor

13. Ball coupling

hinge for proper

camera orienta-

tion

14. camera feet

>1 - 2 m

PARENT UNIT:

Switching on/off:

press and hold for 2 seconds to turn off

Volume:

Use the and buttons to set the loudness of the sounds

from the baby room that you hear through the speaker of the

parent unit.

While adjusting, the volume level will be indicated on the

display and the icon will appear in the upper part when the

volume level is set to 0 (no sound).

Switching on/off automatically: (VOX)

You can set the parent unit to turn off when the baby is sleep-

ing quietly and the baby unit is not detecting any sound, and

let it turn on again as soon as the baby starts to cry.

Here you can set the trigger level for turning on images and

sound:

1. Press the button and use the or button to MENU

scroll to the option

2. Use the and buttons to decrease or increase the

sensitivity level:

: low sensitivity, the parent unit turns on only when loud

sounds are being detected

: high sensitivity, the parent unit also switches on

when low sounds are being detected

: maximum sensitivity, the parent unit remains

switched on

3. Press the button to save your settings and leave MENU

the menu

Switching the display on/off manually:

When the display is turned off because no sound is being de-

tected, but you would still like to check, you can briey press

the button to temporarily switch on the display. Press the

button again to turn the display off.

MULTI-CAMERA

INTRODUCTION:

You can register up to a maximum of 4 baby units (cameras)

on the DVM-67 parent unit. Separate cameras are available

via the service department of Alecto via 073 6411 355 (Neth-

erlands), 03 238 5666 (Belgium) or via internet www.alecto.nl

Read paragraph 4.2 (Multi-camera) for instructions on how

you can use the parent unit to switch to the image from other

cameras.

REGISTERING ADDITIONAL CAMERAS:

1. Connect the power adaptor supplied with the camera to

the new camera and turn the camera on.

2. Press the button on the parent unit and use the MENU

or button to select the option.

3. Use the and buttons to select the number you want to

assign the camera to and press the button.MENU

4. An hourglass will appear on the display to indicate that the

parent unit is currently searching for the new camera.

5. Press and hold the PAIR button on the baby unit until after

several seconds the image of the new camera appears on

the display of the parent unit.

The new camera is now registered and ready for use.

DEREGISTERING ADDITIONAL CAMERAS:

Follow the steps below to deregister faulty cameras or cam-

eras no longer in use:

1. Press the button on the parent unit and use the MENU

or button to select the option; the display will now

show the numbers of all registered cameras.

2. Use the and buttons to select the camera you want to

deregister.

3. Press and hold the TALK button until X and V appear on

the display.

4. Use the and buttons to select the V option to deregis-

ter the camera (or select X to cancel the deregistration)

5. Press the MENU button to conrm the deregistration.

TIPS AND WARNINGS

GENERAL:

• Thoroughly read the user’s manual and follow all

indications.

• Never place the baby unit or parent unit in wet or humid

room or environment.

• Ensure adequate heat dissipation; never cover the parent

unit, the baby unit and/or the power adapter(s) and never

place them directly next to a heat source.

• Only use the supplied adapter(s); connecting a different

type of adapter will damage the electronics.

• Make sure the adapter cables are free of any damage and

ensure nobody can trip or fall because of these cables.

• Never dismantle the parent unit, the baby unit and/or the

power adapter(s); only qualified personnel is authorized

to do so.

INSTALLATION:

• Only connect or disconnect the power adapter to/from

the baby unit or parent unit when the power adapter is

removed from the wall socket.

• Never install the DVM-67 during thunder storms.

• Never touch any non-isolated adapter cables, unless the

adapters are removed from the wall socket.

INTERFERENCE-FREE:

• This baby display monitor is digitally coded. This means

you will never receive signals from other devices, nor can

the signal from your baby unit(s) be received by e.g. your

neighbors.

• In case the baby unit(s) or parent unit is placed in or in the

close vicinity of electromagnetic fields, the signal (images

or sound) can be slightly affected. If this happens, try

a different location for the baby unit(s) or parent unit or

move, if possible, the source of the interference.

EAVESDROPPING/WIRETAPPING:

• Eavesdropping/wiretapping of the signals from this baby

video monitor is nearly impossible. Not only must one be

within range of the baby video monitor, one also needs

some very costly equipment.

MAINTENANCE:

• Only clean the baby monitor with a moist cloth; never

use chemical cleaners. Before any cleaning, you must

disconnect the adapters.

RANGE:

• The baby display monitor has a range of up to 300 meters

in an open field and up to 50 meters indoors; this range

depends on local circumstances. When the units get out

of range from each other, the display will first ‘freeze’

for several seconds (no motion) while flashes on the

display, followed by after another few seconds.

DELAY IN IMAGES AND SOUND:

• The baby unit transmits the images and sound to the

parent unit in digital blocks. The parent unit converts

these signals back to a recognizable image and a

comprehensible sound. Therefore, there is a small delay

between the moment of movement and making sounds

and the display and sounds of the parent unit.

• Besides that, the sounds and images on the parent unit

are not exactly simultaneous.

ENVIRONMENT AND DISCARDING:

• The packaging of this baby video monitor can be

discarded as waste paper. However, we advise you to

save this packaging so you can adequately protect the

devices for transportation.

• Faulty or exhausted batteries or battery packs

should be taken to your local depot for small

chemical waste or to dedicated battery collection

points. Never dispose of batteries or battery packs

as normal household waste.

• In case the baby video monitor is being replaced, please

return it to your supplier; they will guarantee environment-

friendly processing.

PROBLEMS:

• no image, no sound:

– are the parent unit and baby unit switched off? (battery

charged, battery full?)

– is the parent unit within range of the baby unit?

– is the baby unit switched off because no sound is being

detected?

– maybe the display of the parent unit is turned off with

the button?

– is the volume at the parent unit set to 0 (off)?

• If the above is all in order, remove the adapters from the

wall sockets, take the rechargeable battery out of the

parent unit, wait at least one minute and then reconnect

everything. Now, switch the parent unit and baby unit back

on.

• If you still receive no images or sound, please contact

the customer service of Alecto via the phone number 073

6411 355 (Netherlands), 03 238 5666 (Belgium), 0180 503

0085 (Germany) or via internet www.alecto.nl

SPECIFICATIONS

Range: up to 50 meters indoors

up to 300 meters outdoors

Parent unit power: 3.6V NiMH battery pack,

900mAh

6VDC 600mA power adapter

(incl.),

model: S003IV0600060

Baby unit power: 6VDC 600mA power adapter

(incl.),

model: S003IV0600060

Frequency: 2.4GHz, digital frequency

hopping (FHSS) / 21 channels

Display: 2.0” color LCD display

QVGA 220*176 pixels

Recharging time parent unit battery:

+/- 10 hours *

Life-span parent unit battery: 6~10 hours *

Temperature sensor range: 0°C - 50°C

Accuracy: ± 2°C (at 25°C)

*: the times mentioned above are references only and depend

on the usage, condition and quality of the batteries.

WARRANTY

For the Alecto DVM-67 you have a warranty of 24 months

from the date of purchase. During this period, we guarantee

the free repair of defects caused by material and workmanship

errors. All this subjected to the final assessment of the

importer.

HOW TO HANDLE: If you notice any defect, first refer to the

user’s manual. If the manual provides no definite answer,

please contact the supplier of this baby video monitor or

contact customer service of Alecto on telephone number 073

6411 355 (Netherlands) 03 238 5666

(Belgium) or via the Internet www.alecto.nl

THE WARRANTY BECOMES NULL AND VOID: in case

of improper use, incorrect connections, leaking and/or

incorrectly installed batteries, use of unoriginal parts or

accessories, negligence and in case of defects caused by

moisture, fire, flooding, lightning and natural disasters. In case

of unauthorised modifications and/or repairs performed by

third parties. In case of incorrect transportation of the device

without adequate packaging and when the device is not

accompanied by this warranty card and proof of purchase.

The warranty does not cover connecting cables, plugs

and batteries. All further liability, especially concerning any

consequential damages, is excluded.

USE

BABY-UNIT:

Switching on/off:

press and hold for 2 seconds to turn off

The green indicator on the baby unit ashes while the baby

unit is trying to establish a connection with the parent unit, this

indicator remains lit when the connection is successful.

Volume:

Use the and buttons to adjust the reception volume for

the talk-back function from the parent unit.

Automatic night vision:

The baby unit is provided with built-in infra-red LEDs; these

LEDs will switch on automatically when the baby room turns

dark and will switch of again when it becomes light.

The LEDs can illuminate objects up to a distance of approxi-

mately 2 meters.

When it’s dark, that is when the night vision LEDs are

switched on, the images on the parent unit will be displayed in

black and white.

Attention: infra-red light cannot be perceived by the human

eye; that means you cannot tell whether the infra-red LEDs

are switched on with the naked eye. Depending on the type of

the infra-red LED, you might be able to see a red glow.

Temperature display:

The upper right corner of the parent unit’s display shows the

temperature of the baby’s room. You can set this display to be

expressed in degrees Celsius or in degrees Fahrenheit:

1. Press the button and use the or button to MENU

select the option.

2. Use the and buttons to switch between °C and °F.

3. Press the button to save your settings and leave MENU

the menu.

Don’t forget that the temperature is only an indication.

Multi-camera: (also see chapter 5)

In case you have registered multiple cameras on the parent

unit, you can follow the steps below to manually switch to

another baby unit or to automatically show the images of all

registered baby units one after the other:

1. Press the button on the parent unit and use the MENU

or button to select the option: the display will now

indicate the numbers of all registered cameras.

2. Use the and buttons to select the camera you want to

view or select to show all registered cameras one after

the other, and press the button.MENU

The unit does NOT automatically switch to a camera

where sound is being detected.

Leaving the display switched on continuously:

If you don’t want the display to turn off automatically when no

sound is being detected, follow these steps:

1. Press the button and use the or button to MENU

select the option.

2. Use the and to switch between:

X: display is always turned on

V: display will turn off when no sound is being detected

3. Press the button to save your settings and leave MENU

the menu

Talking back:

With the display switched on, press the TALK button to talk

back to your baby. Keep the button depressed for as long as

you are speaking and release the button to listen.

You can adjust the volume at the baby unit using the and

buttons.

Zoom function:

Press the button to turn on the zoom function (moving the

image somewhat closer) and press the button to turn off

the zoom function.

When the zoom function is switched on, the icon will ap-

pear in the upper part of the display.

With the zoom function activated, press and hold the , ,

or button to move the image to the left, to the right, up or

down (attention: the camera doesn’t actually move, the display

merely shows another part of the available image).

Brightness:

1. Press the button and use the or button to MENU

select the option.

2. Press the and buttons to decrease or increase the

display brightness.

3. Press the button to save your settings and leave MENU

the menu.

Service Help

WWW.ALECTO.NL

SERVICE@ALECTO.NL

NL 073 6411 355

(Lokaal tarief)

BE 03 238 5666

(Lokaal tarief)

(Tarif local)

DE 0180 503 0085

Lokale Festnetzkosten

Hesdo, Australiëlaan 1

5232 BB, ‘s-Hertogenbosch

The Netherlands

V1.0

Product specificaties

Merk:	Alecto
Categorie:	Babyfoon
Model:	DVM-671

Heb je hulp nodig?

Als je hulp nodig hebt met Alecto DVM-671 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Babyfoon Alecto

Alecto DVM-240 BEELD Handleiding

14 November 2024

Alecto DVM-200 Handleiding

14 November 2024

Alecto DVM200XL Handleiding

4 December 2024

Alecto DVM2028 Handleiding

5 November 2024

Alecto DVM2043C Handleiding

20 Oktober 2024

Alecto DVM2028C Handleiding

20 Oktober 2024

Alecto DVM-140 Handleiding

14 Juni 2023

Alecto FR-20 Handleiding

7 Juni 2023

Alecto DVM-525 Handleiding

4 Juni 2023

Alecto DBX-88 LIMITED Handleiding

28 Mei 2023

Handleiding Babyfoon

Nieuwste handleidingen voor Babyfoon

VTech RM9751 Handleiding

13 December 2024

VTech RM5754-2HD Handleiding

13 December 2024

VTech RM5764-2HD Handleiding

13 December 2024

VTech VC2105 Handleiding

13 December 2024

VTech RM2751 Handleiding

13 December 2024

VTech RM5754HD Handleiding

13 December 2024

Oricom SC330 Handleiding

10 December 2024

D-Link DCS-825L Handleiding

23 November 2024

Chipolino Polaris Handleiding

16 November 2024

VTech VM3252 Handleiding

16 November 2024