Zodiac ZT700B Handleiding


Lees hieronder de ๐Ÿ“– handleiding in het Nederlandse voor Zodiac ZT700B (3 pagina's) in de categorie Waterfilter. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
1-4
FUNCTION
INSTALLATION
(Link by Bolt on Valve)
THIS FILTER OPERATES UNDER HIGH PRESSURE. WHEN ANY PART OF THE CIRCULATING
SYSTEM (e.g., CLAMP, PUMP, FILTER, VALVES, ETC.) IS SERVICED, AIR CAN ENTER THE
SYSTEM AND BECOME PRESSURIZED . PRESSURIZED AIR CAN CAUSE THE LID OR VALVE TO
BE BLOWN OFF WHICH CAN RESULT IN SEVERE INJURY, DEATH, OR PROPERTY DAMAGE
TURN PUMP OFF BEFORE CHANGING VALVE POSITION.
WARNING
!
!
4-4
TO PREVENT DAMAGE TO THE PUMP AND FOR PROPER OPERATION OF THE SYSTEM,
CLEAN PUMP STRAINER AND SKIMMER BASKETS REGULARLY.
!
FILTER
BACKWASH
RINSE
WASTE
RECIRCULATE
CLOSED
Valve Position
Normal Filtration and Vacuuming
Cleaning Filter by reversing the flow
Used after backwash to flush dirt from valve
By-passes filter, used for vacuuming to waste or lowering water level
By-passes filter for circulating water to pool
Shuts off all flow to filter or pool
Function
DO NOT UNSCREW SCREWS OF FLANGE CLAMP WHILE PUMP IS RUNNING.
!
ZOFI09081122
FUNCTIONS OF VALVE POSITIONS
WASTE
FILTER
BACKWASH RINSE
WASTE
RECIRCULATE
CLOSED
WASTE WASTE
WASTE WASTE WASTE
IN FLOW OUT FLOW IN FLOW OUT FLOW IN FLOW OUT FLOW
IN FLOW OUT FLOW IN FLOW OUT FLOW IN FLOW OUT FLOW
GENERAL
TO ASSEMBLE:
SERVICING VALVE( Stop pump,close gate valve in suction&discharge before proceeding):
a. Set handle in filter position. b. Remove cover screws. c. Lift cover and key assembly out.
1. Place valve key so that wedge opening is at TOP port (handle in Filter psn.). Flat edge of cover screw lug should align with
flat edge of body screw lug.
2. Position cover oโ€™ring.
3. Secure assembly to body with cover screws. Tighten cover screws evenly and alternately. Do not over-tighten.
The filter uses special filter sand to remove dirt particles from pool water. The filter sand is loaded into the filter tank and functions as
a permanent dirt removing media. When the control valve is in the FILTER position, the pool water which contains suspended dirt
particles, is pumped through your piping system and is automatically directed by the patented filter control valve to the top of the filter
tank. As the pool water is pumped through the filter, dirt particles are trapped by the sand bed, and filtered out. The cleaned pool water is
returned from the bottom of the filter tank, through the control valve and back to the pool through the piping system. This entire sequence
is continuous and automatic. It provides for total recirculation of pool water through your filter and piping system.
After a period of time, the accumulated dirt in the filter causes a resistance to flow, and the flow diminishes. This means it is time to
clean your filter. With the control valve in the BACKWASH position, the water flow is automatically reversed through the filter so that it
is directed to the bottom of the tank, up through the sand, flushing the previously trapped dirt and debris out the waste line. Once the filter
is back-washed of dirt, set control valve to RINSE position and run pump for about 1/2 to 1 minute, and then set the control valve in the
FILTER position, to resume normal filtering.
NOTE: Turn pump off before changing valve position.
Only simple tools (screwdriver and wrenches), plus pipe sealant for plastic adapters, are required to install and
service the filter.
1. The filter should be placed on a level concrete slab, very firm ground, or equivalent. The filter should be placed
2. Loading the sand media. Filter sand media is loaded through the top opening of the filter.
a. Loosen the flange clamp and remove filter control valve (if previously installed).
b. Cap internal pipe with plastic cap to prevent sand from entering it.
c. We recommend filling the tank approximately 1/2 way with water to provide a cushion effect when the filter
d. Carefully pour in correct amount and grade of filter sand. (Be sure center pipe remains centered in opening.)
internal pipe.
in the right position so that the piping connections, control valve are convenient and accessible for operation and service.
sand is poured in. This helps protect the under-drain laterals from excessive shock.
Sand surface should be leveled and should come to about the middle of the filter tank. Remove plastic cap from
TITAN SERIES SAND FILTER
ZT800, ZT900Models:ZT700B,
2-4
3. Assemble filter control valve into the filter tank.
a. Insert filter control valve (with o'ring in place) into the tank neck, taking care that the center pipe slips into the hole
b. Place two plastic clamps around valve flange and tank flange and tighten just enough so that the valve may be
d. Connect pump to control valve opening marked PUMP. After connections are made, tighten valve flange clamps with
plumbing connections, suction lines to pump, waste, etc.
5. Make electrical connections to pump per pump instructions.
6. To prevent water leakage, make sure all pipe connections are tight.
4. Make return to pool pipe connection to control valve opening marked RETURN and complete other necessary
MAIN DIMENSION
in the bottom of the valve.
rotated on tank for final positioning.
c. Carefully screw pressure gauge (with o'ring in place) into tapped hole in valve body. Do not over-tighten.
screwdriver, tapping around clamp with screwdriver handle to help seat valve flange clamp.
REPLACEMENT PARTS OF FILTER
3-4
1. Make sure the correct amount of filter media sand is located in the tank and all connections have been connected and secured.
2. Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal, always depress handle
before turning.)
3. Prime and start pump according to pump instructions (be sure all suction and return lines are open), allowing the filter tank to fill with
water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The initial back-washing of the filter is
recommended to remove any impurities or fine sand particles in the sand media.
4. Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about 1/2 to 1 minute. Turn
pump off and set valve to FILTER position and restart pump. The filter is now operating in the normal filter mode, filtering dirt particles
from the pool water.
5. Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and tighten connections, bolts, nuts,
as required.
6. Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the pump and general piping
system.) As the filter removes dirt and impurities from the pool water, the accumulation of dirt in the filter will cause the pressure to rise
and diminish the water flow. When the pressure gauge reading is 1.5 bar, higher than the initial "clean" pressure you noted, it is time to
backwash the filter (see BACKWASH under filter and control valve functions).
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
INSTALL/START-UP OF FILTER
heavy initial dirt load in the water.
DIMENSION TABLE
REPLACEMENT PARTS OF MULTIPORT VALVE
Item Part No. Description Qty
1 W01013003 Handle (Big) 1
2 W03018008 Pin for Handle 1
3 W01181027 Washer for Handle 1
4 W89280301 M6*32 Screw with Nut 10
5 W01013019 50mm Top Mount Valve Standard Lid (Black) 1
6 W03014014 Spring for 50mm Top Mount Valve 1
7 W02011006 O-Ring for 50mm Top Mount Valve Lid 1
8 W02011022 O-Ring for 50mm Top Mount Valve Rotor 2
9 W01181002 Washer for Spring 2
10 W01021002 50mm Valve Rotor 1
11 W02311003 Spider Gasket 1
12 W01013027 50m m Top Mount Valve Bottom Body (black) 1
13 W01013029 50mm Water Tube 1
14 W01013030 50mm Diffuser 1
15 W02011005 O-Ring for Diffuser 1
16 W02011007 O-Ring for Connector 6
17 W01013031 50m m Connector with External Thread (Black) 3
18 W01171154 50mm Union Adaptor 3
19 W01013032 50mm Union Nut (Black) 3
20 W89280104 Sight Glass with O-Ring 1
21 W01111048 Connector for Pressure Gauge/Stopper 1
22 W89021703 Drain Plug with O-ring 1
23 W06011009 Oil Pressure Gauge With O-ring (50psi) 1
AB
Model
High Diameter
mm
mm
mm
Valve Port
Size Sand
kg
1300
1200
V900
V800 800
900
350
25050
50
B
A
1092V700B 723
21550
Item Part No. Description Qt y
1 W88280306 50mm Top Mount Valve 1
2 W89010601 Nut with O-Ring 1
W06011009 Oil Pressure Gauge With O-ring (50 psi) 1
W01111048 Connector for Pressure Gauge/Stopper 1
4 W89280103 50mm Union set (3 pieces) with O-Ring 3
5 W89280104 Sight glass with O-Ring 1
6 W02011126 Filter Neck Gasket 1
W89010612 ZT700B Filter Tank With Base 1
W89010603 ZT800 Filter Tank With Base 1
W89010604 ZT900 Filter Tank With Base 1
W89010611 ZT700B Lateral Assembly With Center Pipe 1
W89010607 ZT800 Lateral Assembly With Center Pipe 1
W89010608 ZT900 Lateral Assembly With Center Pipe 1
9 W01172010 ZT800-ZT900 Laterals (185mm) 8
10 W89010107 Water Drain Set 1
7
8
3


Product specificaties

Merk: Zodiac
Categorie: Waterfilter
Model: ZT700B

Heb je hulp nodig?

Als je hulp nodig hebt met Zodiac ZT700B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Waterfilter Zodiac

Handleiding Waterfilter

Nieuwste handleidingen voor Waterfilter

JANDY

JANDY CS250 Handleiding

18 December 2024
JANDY

JANDY CS150 Handleiding

18 December 2024
JANDY

JANDY CS100 Handleiding

18 December 2024
Heissner

Heissner HLF6000 Handleiding

16 December 2024
Haier

Haier HRO4H85-3 Handleiding

10 December 2024
Haier

Haier HRO6H85-3 Handleiding

10 December 2024
Haier

Haier HBWS-S15 Handleiding

10 December 2024
Haier

Haier HBCF-S3002 Handleiding

10 December 2024
Haier

Haier HBP-V40 Handleiding

10 December 2024