Zodiac Titan TP650 Handleiding
Zodiac
Waterfilter
Titan TP650
Lees hieronder de 📖 handleiding in het Nederlandse voor Zodiac Titan TP650 (3 pagina's) in de categorie Waterfilter. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/3
1-4
FUNCTION
INSTALLATION
THIS FILTER OPERATES UNDER HIGH PRESSURE. WHEN ANY PART OF THE CIRCULATING
SYSTEM (e.g., CLAMP, PUMP, FILTER, VALVES, ETC.) IS SERVICED, AIR CAN ENTER THE
SYSTEM AND BECOME PRESSURIZED . PRESSURIZED AIR CAN CAUSE THE LID OR VALVE TO
BE BLOWN OFF WHICH CAN RESULT IN SEVERE INJURY, DEATH, OR PROPERTY DAMAGE
TURN PUMP OFF BEFORE CHANGING VALVE POSITION.
WARNING
!
!
4-4
TO PREVENT DAMAGE TO THE PUMP AND FOR PROPER OPERATION OF THE SYSTEM,
CLEAN PUMP STRAINER AND SKIMMER BASKETS REGULARLY.
!
DO NOT UNSCREW SCREWS OF FLANGE CLAMP WHILE PUMP IS RUNNING.
!
ASFI09051703
FUNCTIONS OF VALVE POSITIONS
WASTE
FILTER
BACKWASH RINSE
WASTE
RECIRCULATE
CLOSED
WASTE WASTE
WASTE WASTE WASTE
IN FLOW OUT FLOW IN FLOW OUT FLOW IN FLOW OUT FLOW
IN FLOW OUT FLOW IN FLOW OUT FLOW IN FLOW OUT FLOW
GENERAL
SERVICING VALVE( Stop pump,close gate valve in suction&discharge before proceeding):
a. Set handle in filter position. b. Remove cover screws. c. Lift cover and key assembly out.
TO ASSEMBLE:
1. Place valve key so that wedge opening is at TOP port (handle in Filter psn.). Flat edge of cover screw lug should align with
flat edge of body screw lug.
2. Position cover o’ring.
3. Secure assembly to body with cover screws. Tighten cover screws evenly and alternately. Do not over-tighten.
The filter uses special filter sand to remove dirt particles from pool water. The filter sand is loaded into the filter tank and functions as
a permanent dirt removing media. When the control valve is in the FILTER position, the pool water which contains suspended dirt
particles, is pumped through your piping system and is automatically directed by the patented filter control valve to the top of the filter
tank. As the pool water is pumped through the filter, dirt particles are trapped by the sand bed, and filtered out. The cleaned pool water is
returned from the bottom of the filter tank, through the control valve and back to the pool through the piping system. This entire sequence
is continuous and automatic. It provides for total recirculation of pool water through your filter and piping system.
After a period of time, the accumulated dirt in the filter causes a resistance to flow, and the flow diminishes. This means it is time to
clean your filter. With the control valve in the BACKWASH position, the water flow is automatically reversed through the filter so that it
is directed to the bottom of the tank, up through the sand, flushing the previously trapped dirt and debris out the waste line. Once the filter
is back-washed of dirt, set control valve to RINSE position and run pump for about 1/2 to 1 minute, and then set the control valve in the
FILTER position, to resume normal filtering.
NOTE: Turn pump off before changing valve position.
TITAN SERIES SAND FILTER
Model : TP500, TP650, TP700
(Link by Clamp type Valves)
Only simple tools (screwdriver and wrenches), plus pipe sealant for plastic adapters, are required to install and
service the filter.
1. The filter should be placed on a level concrete slab, very firm ground, or equivalent. The filter should be placed
2. Loading the sand media. Filter sand media is loaded through the top opening of the filter.
a. Loosen the flange clamp and remove filter control valve (if previously installed).
b. Cap internal pipe with plastic cap to prevent sand from entering it.
c. We recommend filling the tank approximately 1/2 way with water to provide a cushion effect when the filter
d. Carefully pour in correct amount and grade of filter sand. (Be sure center pipe remains centered in opening.)
internal pipe.
in the right position so that the piping connections, control valve are convenient and accessible for operation and service.
sand is poured in. This helps protect the under-drain laterals from excessive shock.
Sand surface should be leveled and should come to about the middle of the filter tank. Remove plastic cap from
Valve Position Function
FILTER
BACKWASH
RINSE
WASTE
RECIRCULATE
CLOSED
Normal Filtration and Vacuuming
Cleaning Filter by reversing the flow
Used after backwash to flush dirt from valve
By-passes filter, used for vacuuming to waste or lowering water level
By-passes filter for circulating water to pool
Shuts off all flow to filter or pool
2-4
3. Assemble filter control valve into the filter tank.
a. Insert filter control valve (with o'ring in place) into the tank neck, taking care that the center pipe slips into the hole
b. Place two plastic clamps around valve flange and tank flange and tighten just enough so that the valve may be
d. Connect pump to control valve opening marked PUMP. After connections are made, tighten valve flange clamps with
plumbing connections, suction lines to pump, waste, etc.
5. Make electrical connections to pump per pump instructions.
6. To prevent water leakage, make sure all pipe connections are tight.
4. Make return to pool pipe connection to control valve opening marked RETURN and complete other necessary
MAIN DIMENSION
in the bottom of the valve.
rotated on tank for final positioning.
c. Carefully screw pressure gauge (with o'ring in place) into tapped hole in valve body. Do not over-tighten.
screwdriver, tapping around clamp with screwdriver handle to help seat valve flange clamp.
REPLACEMENT PARTS OF FILTER
3-4
1. Make sure the correct amount of filter media sand is located in the tank and all connections have been connected and secured.
2. Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal, always depress handle
before turning.)
3. Prime and start pump according to pump instructions (be sure all suction and return lines are open), allowing the filter tank to fill with
water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The initial back-washing of the filter is
recommended to remove any impurities or fine sand particles in the sand media.
4. Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about 1/2 to 1 minute. Turn
pump off and set valve to FILTER position and restart pump. The filter is now operating in the normal filter mode, filtering dirt particles
from the pool water.
5. Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and tighten connections, bolts, nuts,
as required.
6. Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the pump and general piping
system.) As the filter removes dirt and impurities from the pool water, the accumulation of dirt in the filter will cause the pressure to rise
and diminish the water flow. When the pressure gauge reading is 1.5 bar, higher than the initial "clean" pressure you noted, it is time to
backwash the filter (see BACKWASH under filter and control valve functions).
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
INSTALL/START-UP OF FILTER
heavy initial dirt load in the water.
B
B
B
B
B
A
A
A
A
A
REPLACEMENT PARTS OF MULTIPORT VALVE
DIMENSION TABLE
AB
Model
High Diameter
mm
mm
845TP500 535
950TP650 635
mm
Valve Port
Size Sand
kg
85
145
40
40
1020TP700 710
210
40
Item Part No.
1 W88280105 40mm Top Mount Valve
2 W89280101 40mm Union With Sight Glass, O-Ring
3 W89280102 40mm Union Set (2 Pieces) With O-Ring
W06021001 Plastic Pressure Gauge With O-Ring (35psi)
W01111048 Connector for Pressure Gauge/Stopper
W89010119 M6*50 Screws With Nut
W01271010 Clamp Lock
6 W02011134 O-Ring for Filter Neck
W01331008 TP500 Filter Tank
W01331010 TP650 Filter Tank
W01331009 TP700 Filter Tank
W89011605 TP500 Lateral Assembly with Center Pipe
W89011606 TP650 Lateral Assembly with Center Pipe
W89011607 TP700 Lateral Assembly with Center Pipe
9 W01172008 TP500-TP700 Laterals (126mm)
10 W89011601 Water Drain Set
11 W01111062 TP500-TP700 Filter Base
8
Description
4
5
7
Item Part No. Des cription
1 W01013003 Handle(Big)
2 W03018008 Pin for Handle
3 W01181001 Washer for Handle
4 W89280107 M6×30 Screw with Nut for Standard Lid
5 W01013004 40mm Top Mount Valve Standard Lid (Black)
6 W02011002 O-Ring for 40mm Valve Lid
7 W01181002 Washer for Spring
8 W03014001 Spring for 40mm Top Mount Valve
9 W02011022 O-Ring for 40mm Valve Rotor
10 W01021001 40mm Valve Rotor
11 W02311002 Spider Gasket
12 W01013007 40mm Top Mount Valve Bottom Body Clamp（black)
13 W01013011 40mm Diffuser
14 W02011001 O-Ring for Diffuser
15 W01013012 40mm Top Mount Valve Over Drain Diffuser
16 W02011134 O-Ring
17 W02011151 O-Ring for 40mm Connector
18 W01013015 40mm Connector (black)
19 W02011003 O-Ring for 40mm Union
20 W01171153 40mm Union (A/E)
21 W01013017 40mm Union Nut (black)
22 W01041002 40mm Union With Sight Glas s (short)
23 W01172026 40mm Union With Sight Glas s Holder
24 W01111048 Connector for pres sure gauge/stopper
25 W89021703 Drain Plug with O-ring
26 W06011009 Oil Pressure Gauge With O-ring (50Psi)
Product specificaties
| Merk: | Zodiac |
| Categorie: | Waterfilter |
| Model: | Titan TP650 |
Heb je hulp nodig?
Als je hulp nodig hebt met Zodiac Titan TP650 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Waterfilter Zodiac
16 Juni 2023
16 Juni 2023
15 Juni 2023
14 Juni 2023
10 Juni 2023
8 Juni 2023
28 Mei 2023
22 Mei 2023
21 Mei 2023
18 Mei 2023
Handleiding Waterfilter
- Waterfilter Electrolux
- Waterfilter Philips
- Waterfilter Panasonic
- Waterfilter LG
- Waterfilter JBL
- Waterfilter Tefal
- Waterfilter Zanussi
- Waterfilter Astralpool
- Waterfilter Avanti
- Waterfilter Bartscher
- Waterfilter Breville
- Waterfilter Brita
- Waterfilter BWT
- Waterfilter Eden
- Waterfilter Eheim
- Waterfilter Fisher And Paykel
- Waterfilter Franke
- Waterfilter GE
- Waterfilter Grohe
- Waterfilter Haier
- Waterfilter Kent
- Waterfilter Laica
- Waterfilter Midea
- Waterfilter Smeg
- Waterfilter Solac
- Waterfilter Sunbeam
- Waterfilter Terraillon
- Waterfilter Ufesa
- Waterfilter Verbatim
- Waterfilter Jata
- Waterfilter Jura
- Waterfilter Juwel
- Waterfilter Oase
- Waterfilter Imetec
- Waterfilter Fluval
- Waterfilter Eldom
- Waterfilter Aarke
- Waterfilter Ecowater
- Waterfilter Flama
- Waterfilter FIAP
- Waterfilter Pureit
- Waterfilter Everpure
- Waterfilter Consul
- Waterfilter T.I.P.
- Waterfilter MSR
- Waterfilter Billi
- Waterfilter LifeStraw
- Waterfilter Baracuda
- Waterfilter Waterdrop
- Waterfilter Zip
- Waterfilter Waterco
- Waterfilter Aquasure
- Waterfilter ZeroWater
- Waterfilter Beemur
- Waterfilter Ionmax
- Waterfilter Puretec
- Waterfilter Tunze
- Waterfilter Aqua Medic
- Waterfilter PUR
- Waterfilter Sera
- Waterfilter Oliveri
- Waterfilter Hydor
- Waterfilter Aquael
- Waterfilter LARQ
Nieuwste handleidingen voor Waterfilter
21 November 2024
19 November 2024
19 November 2024
18 November 2024
15 November 2024
14 November 2024
28 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024