WyreStorm EX-SW-0301-H2 Handleiding

WyreStorm Receiver EX-SW-0301-H2

Lees hieronder de 📖 handleiding in het Nederlandse voor WyreStorm EX-SW-0301-H2 (4 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

IMPORTANT! Installation Requirements

This product was released in 2 different versions which contain different

chassis designs and feature sets. Refer to for Identifying Product Versions

details.

This extender requires connection via RS-232 or Ethernet in order to congure

functions such as EDID. Ensure that the following items are on hand before

proceeding with the installation.

• PC or Mac

• Telnet and Terminal software such as PuTTY

• USB COM Port Adapter (Not Included)

• WyreStorm Part: CAB-USB-3PIN

• Network router and/or switch if using IP telnet for conguration.

• Latest version of the EX-SW-0301-H2 API for advanced conguration not

covered in this document.

In the Box

1x EX-SW-0301-H2 Transmitter

1x EX-SW-0301-H2 Receiver

1x AC 100-240V 50/60Hz to DC 12V Power Adapter

5x 3-pin Phoenix Connectors (version1)

3x 3-pin Phoenix Connectors (version 2)

2x 4-pin Phoenix Connectors (version 2)

4x Mounting Brackets (1set for Transmitter/1set for Receiver)

1x Quickstart Guide (This Document)

Identifying Product Versions

This product was released in 2 different versions which contain different chassis designs and feature sets. The differences are identied throughout this

document in order to make installation and use easier. Versions can be identied by a v# after the model number on the product chassis model number sticker.

Note that version 1 of this product may not contain a v1 after the product while all version 2s will contain a v2 after the model number.

Operational Differences

Feature Version 1 Version 2

Web UI for conguration and control N/A Added in version 2

RS-232 Port Pinout 3-pin Phoenix 4-pin Phoenix

EX-SW-0301-H2 Quickstart Guide | 180821

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features before beginning the

installation process.

Basic Wiring Diagram

KEY

HDMI/DisplayPort

HDBaseT

RS-232/Serial

Analog Audio

Analog Video

Control System

Projector

Personal Computer

Laptop

Media Player

Digital Signage

Player

Amplifier

Projector Screen

RX to TX

3:1 HDMI/VGA/DP Switching Extender with Scaling Receiver,

Relay Triggering and HDCP 2.2

EX-SW-0301-H2 Quickstart Guide

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its

entirety before running or terminating any wires to ensure proper operation and to avoid damaging the equipment.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on

signal transmission which may limit performance. Steps should be taken

to minimize or remove these factors completely during installation for best

results

• WyreStorm recommends using pre-terminated HDMI and DP cables due to

the complexity of these connector types. Using pre-terminated cables will

ensure that these connections are accurate and will not interfere with the

performance of the product.

Communication Connections

RS-232 Wiring

The EX-SW-0301-H2 uses a 3-pin (v1) or 4-pin (v2) RS-232 with no hardware

ow control. Most control systems and computers are DTE where pin 2 is

RX, this can vary from device to device. Refer to the documentation for the

connected device for pin functionally to ensure that the correct connections

can be made.

PC Connection

Connection to a PC requires the use of a USB to 3-pin Port Adapter cable (CAB-

USB-3PIN) in order for a port to be provided on the PC. Note that this adaptor

can be used on both v1 and v2 versions.

Version 1 (3-pin)

3rd Party Device

Pin 1 TX (Transmit) > To > RX (Receive)--- ---

Pin 2 RX (Receive) > To > TX (Transmit)--- ---

Pin 3 G (Gro d) > To > G (Gro d)un --- --- un

WyreStorm Co ectornn

Version 2 (4-pin)

3rd Party Device

Pin 1 V DC Out > To > Reserved12 --- ---

Pin 2 TX (Transmit) > To > RX (Receive)--- ---

Pin 3 RX (Receive) > To > TX (Transmit)--- ---

Pin 4 G (Gro d) > To > G (Gro d)un --- --- un

WyreStorm Co ectornn

Audio Connections

Audio In (TX)

The audio connections use a 3.5mm (1/8in) TRS Stereo Jack.

Audio Out (TX/RX)

3rd Party Device

Pin 1 L (Left Signal) > To > Left Signal (L+)--- ---

Pin 2 R (Right Signal) > To > Right Signa (R+)--- --- l

Pin 3 GND (Gro d) > To >un --- ---

Left Gro d (L-)un

Right Gro d (R-)un

WyreStorm Co ectornn

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that power is being supplied to the transmitter and receiving device.

• Verify that the HDBaseT cable is properly terminated following EIA568B

standard.

• Verify that the output resolution of the source and display is supported by

this extender.

• Congure EDID Settings to a lower resolution.

• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.

• Verify that all source and HDBaseT connections are not loose and are

functioning properly.

No or Intermittent 3rd party Device Control

• Verify that the RS-232/Ethernet cables are properly terminated following the

Wiring and Connections section.

Relays Not Functioning

• Verify polarity of the relay connections.

Troubleshotting Tips

• WyreStorm recommends using a cable tester or connecting the cable to

other devices to verify functionality.

EX-SW-0301-H2 Quickstart Guide | 180821

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

Relay Wiring

The relays on this extender can be used to be trigger devices such as projector

screens that are Normally Open (NO) or Normally Closed (NC).

3rd Party Device

Pin 1 NO (Normally Open) > To > NO (Norma--- --- lly Open)

Pin 2 Co on (Gro d) > To > Co on (Gro d)mm un --- --- mm un

Pin 3 NC (Normally Closed) > To > NC (Normally Closed)--- ---

WyreStorm Co ectornn

Setup and Conguration

The EX-SW-0301-H2 is congured using RS-232 and/or Telnet commands for IP address, Output Resolution, and EDID. Follow these steps to properly congure

the extender based on the system requirement.

Note: The steps and information provided in this QSG are for basic operation of the extender out of the box. Refer to the EX-SW-0301-H2 API for full

conguration settings.

1. Assign a Static IP Address to ensure proper communication on an IP Network. See Conguring a Static IP Address

2. Set an Output Resolution to be used by the RX. See Conguring RX Output Resolution

3. Set EDIDs to be used at each input of the device. See Conguring Input EDIDs

Communication Settings

The commands listed below can be sent by connecting to either the TX or

RX for RS-232 and the RX only for Ethernet. Each device must be connected

together via HDBaseT in to order to send a command from one device to the

other. The only exception is which requires Conguring a Static IP Address

connection to the RX.

Version 2 or higher of the EX-SW-0301-H2 contains a web UI that can be

accessed by connecting to a network and entering the IP address. We

recommend that the IP address is changed from default before accessing the

web UI for the rst time.

RS-232 and IP Settings

Baud rate: 115200

Data Bits: 8bits

Parity: None

Stop Bits: 1bit

Flow Control: None

Default IP Address 192.168.11.43

Default IP Port 23

Conguring a Static IP Address

By default, the switcher is set to a static IP of 192.168.11.043. We recommend changing this as it shared with other WyreStorm products and may cause

improper communication if left unchanged. Connect to the RX via RS-232 and send the following command to set the IP address.

Conguring RX Output Resolution

By default, all inputs are set to an EDID or 1920x1080@60Hz 2CH. However, this can be congured to suit the installation.

Conguring Input EDIDs

By default, all inputs are set to an EDID or 1920x1080@60Hz 2CH. However, this can be congured to suit the installation.

EX-SW-0301-H2 Quickstart Guide | 180821

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

3 of 4

SET IPADDR STATIC ip4addr [IP Address] netmask [Netmask]<CR><LF>

Example: SET IPADDR STATIC ip4addr 192.168.11.243 netmask 255.255.255.0 <CR><LF>

Response: IPADDR STATIC ip4addr 192.168.11.243 netmask 255.255.255.0 <CR><LF>

Note: This command can only be sent to the receivers (RX) RS-232 port.

Set Output Resolution

SET RES all [Resolution] rx<CR><LF>

Example: SET RES all Fix:1920x1200@60 rx<CR><LF>

Response: RES SET all Fix:1920x1200@60 rx<CR><LF>

Query Output Resolution

GET RES_OUT all rx<CR><LF>

Example: GET RES_OUT all rx<CR><LF>

Response: RES GET all Fix:1920x1200@60 rx<CR><LF>

Resolution = 0~8

0 Auto Scaler (Default)

1 1024x768@60Hz

2 1280x720@60Hz

3 1280x800@60Hz

4 1280x1024@60Hz

5 1920x1080@60Hz

6 1920x1200@60Hz

7 3840x2160@30Hz

8 3840x2160@60Hz 4:4:4

Set Input EDID

SET EDID [Input] [Resolution] [Device]<CR><LF>

Example: SET EDID in1 1 tx<CR><LF>

Response: EDID SET in1 1 tx<CR><LF>

Query Input EDID

GET EDID [Input] [Device]<CR><LF>

Example: GET EDID in1 tx<CR><LF>

Response: EDID GET in1 1 tx<CR><LF>

Input=in1 (VGA) | in2 (HDMI) | in3 (DP)

Device=tx | rx | all

Resolution=1~8

VGA EDID HDMI EDIDs

1 1920x1200@60Hz 2CH 1 3840x2160@30Hz 2CH

2 1920x1080@60Hz 2CH (Default) 2 1920x1080@60Hz 2CH (Default)

3 1680x1050@60Hz 2CH 3 1680x1050@60Hz 2CH

4 1600x900@60Hz 2CH 4 1600x900@60Hz 2CH

5 1440x900@60Hz 2CH 5 1440x900@60Hz 2CH

6 1360x768@60Hz 2CH 6 1360x768@60Hz 2CH

7 1280x768@60Hz 2CH 7 1280x720@60Hz 2CH

8 1024x768@60Hz 2CH 8 1024x768@60Hz 2CH

Product specificaties

Merk:	WyreStorm
Categorie:	Receiver
Model:	EX-SW-0301-H2
Kleur van het product:	Zwart
Soort:	AV-zender & ontvanger
Stroom:	3 A
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Maximum resolutie:	4096 x 2160 Pixels
Aantal USB-aansluitingen:	1
Certificering:	CE \| FCC \| RoHS
HDCP:	Ja
USB-versie:	2.0
Maximale refresh snelheid:	60 Hz
Aansluiting voor netstroomadapter:	Ja
Duurzaamheidscertificaten:	RoHS
Plug and play:	Ja
VGA (D-Sub) invoer ports:	1
DisplayPorts in:	1
Temperatuur bij opslag:	-20 - 70 °C
Upgraden van firmware mogelijk:	Ja
Luchtvochtigheid bij opslag:	10 - 90 procent
Rack-montage:	Ja
Audio-uitgangskanalen:	2.0 kanalen
Power over Ethernet (PoE):	Ja
HDMI in:	3
RJ-45 uitgang ports:	1
HDCP versie:	2.2
Bandbreedte:	9.2 Gbit/s
Aantal HDMI-uitgangen:	1
Receiver afmetingen (B x D x H):	29.5 x 266.2 x 154.7 mm
RJ-45 invoer ports:	1
Operating voltage:	12 V
HDBaseT-poort:	Ja
Maximaal bereik:	70 m
Bedrijfstemperatuur (T-T):	0 - 45 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Receiver gewicht:	940 g
Transmitter afmetingen (WxDxH):	24.5 x 237 x 95.5 mm
Transmitter gewicht:	500 g
Stroomverbruik (zender) (max):	7 W
HDCP- & EDID-omzeiling:	Ja
Ondersteundende kabel types:	Cat6, Cat6a, Cat7, HDMI
Extended display identification data (EDID):	Ja
Stroomverbruik (ontvanger) (max):	17 W
HDCP-passthrough:	Ja
EDID-management:	Ja