WyreStorm EX-70-H2 Handleiding

WyreStorm Receiver EX-70-H2

Lees hieronder de 📖 handleiding in het Nederlandse voor WyreStorm EX-70-H2 (4 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

18Gbps 4K HDR HDBaseT Extender with

HDCP 2.2 and 2-way PoH

EX-70-H2 v2 Quickstart Guide

EX-70-H2 v2 Quickstart Guide | 190227

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the

installation process.

Basic Wiring Diagram

IMPORTANT! Installation Requirements

• This product was released in 2 different versions which contain different

chassis designs and feature sets.

• See Identifying Product Versions for details.

• Visit the product page to download the latest rmware, document version,

additional documentation, and conguration tools.

• Read through the section for important wiring Wiring and Connections

guidelines before creating or choosing premade cables.

• While this product supports CEC, WyreStorm cannot guarantee

compatibility with all forms of CEC communication.

In the Box

1x EX-70-H2 v2 Transmitter

1x EX-70-H2 v2 Receiver

1x IR Emitter

1x IR Receiver

2x 3-pin Terminal Block

1x 18V DC 1A Power Supply (US/UK/EU)

4x Mounting Brackets (2x for TX | 2x for RX)

1x Quickstart Guide (this document)

HDMI

IR Emitter

IR Receiver

18V DC 1A

Power Supply

IR to Control System

CAB-IR-LINK (Sold Separately)

EX-70-H2 Transmitter (TX) EX-70-H2 Receiver (RX)

4K/UHD HDMI Source 4K/UHD HDMI Display

KEY

HDMI

HDBaseT Cat6/7

IR TX and RX

Power

HDBaseT

Cat5e/6/6a/7

Note: Extender set may be powered

by either the TX or RX. Only one

power supply is required.

Front Panel (TX/RX) Rear Panel (TX/RX)

Power LED Solid: The receiver is powered On

Off: The receiver is powered Off

Status LED Flashing: The receiver is operating normally.

Off: The receiver is Not operating normally.

HDCP LED

Solid: HDCP content is present.

Flashing: HDCP content is not present.

Off: No signal.

LINK LED

Solid: Link to receiver has been established.

Flashing: Link to receiver has not been

established.

Power In

5.5mm Screw Down Barrel Jack

Connect to the included 18V DC 1A power

supply to the transmitter or receiver. A power

supply is not required on the other end as it

will be powered using PoH.

HDBT In

HDBT Out

8-pin RJ-45 female

Connect the transmitters HDBT Out to

receivers HDBT In.

IR TX

IR RX

IR TX - 3.5mm (1/8in) Mono Jack: Connect

to the supplied IR emitter to control a local

device from the remote display location via

HDBaseT.

IR RX - 3.5mm (1/8in) Stereo Jack: Connect

to the supplied IR receiver to send IR to the

remote display location via HDBaseT.

See for more IR TX/RX Guidelines

information.

RS-232 1x RS-232: 3-pin Phoenix

HDMI In

HDMI Out

19-pin type A HDMI female

Supports HDMI and DVI/D with adapter

EX-70-H2 v2 Quickstart Guide | 190227

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

EX-70-H2 v2 Quickstart Guide | 190227

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

3 of 4

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on

signal transmission which may limit performance. Steps should be taken

to minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends the use of shielded category cable to minimize

signal noise and interference.

• WyreStorm recommends using pre-terminated HDMI cables due to the

complexity of these connector types. Using pre-terminated cables will

ensure that these connections are accurate and will not interfere with the

performance of the product.

IR TX/RX Guidelines

• Using WyreStorm infrared emitters and receivers is the best way to ensure

that most IR coding formats are transmitted and received by the NetworkHD

system. Other 3rd party emitters and receivers can be used; however, these

devices must operate in the same manner as the WyreStorm devices.

• Due to differences in IR across 3rd party control systems their IR ports

should never be connected directly to a NetworkHD system as an

incompatibility may exist. WyreStorm offers a cable that compensates for

voltage differences as well adjusts for differences in the pins used within the

port. Refer to the product page for more information.CAB-IR-LINK

IR TX Port Pinout

Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.

Tip: Anode

Sleeve: Cathode (IR Signal)

IR RX Port Pinout

Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs

+5V DC to power the included IR receiver.

Tip:

Ring: IR Signal

+5V DC

Sleeve: Ground (GND)

RS-232 Wiring

The EX-70-H2 uses a 3-pin RS-232 with no hardware ow control. Most

control systems and computers are DTE where pin 2 is RX, this can vary from

device to device. Refer to the documentation for the connected device for pin

functionally to ensure that the correct connections can be made.

3rd Party Device

Pin 1 TX (Transmit) > To > RX (Receive)--- ---

Pin 2 RX (Receive) > To > TX (Transmit)--- ---

Pin 3 G (Gro d) > To > G (Gro d)un --- --- un

WyreStorm Co ectornn

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that power is being supplied to the transmitter and receiving device

• Verify that all HDMI and HDBaseT connections are not loose and are

functioning properly

• Verify that the HDBaseT cable is properly terminated following EIA568B

standard

• Verify that the output resolution of the source and display is supported by

this extender

• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.

No or Intermittent 3rd party Device Control

• Verify that the IR and RS-232 cables are properly terminated following the

Wiring and Connections section.

Troubleshooting Tips:

• WyreStorm recommends using a cable tester or connecting the cable to

other devices to verify functionality.

Product specificaties

Merk:	WyreStorm
Categorie:	Receiver
Model:	EX-70-H2
Kleur van het product:	Zwart
Gewicht:	240 g
Breedte:	136.4 mm
Diepte:	74.2 mm
Hoogte:	15.2 mm
Soort:	AV-zender & ontvanger
Type verpakking:	Doos
Stroom:	1 A
Connectiviteitstechnologie:	Bedraad
Maximum resolutie:	4096 x 2160 Pixels
Certificering:	CE \| FCC \| RoHS \| RCM
HDCP:	Ja
Maximale refresh snelheid:	60 Hz
Aansluiting voor netstroomadapter:	Ja
HDMI versie:	2.0
Remote (IR) ingang:	1
Duurzaamheidscertificaten:	RoHS
Plug and play:	Ja
Aantal per verpakking:	1 stuk(s)
Temperatuur bij opslag:	-20 - 70 °C
Luchtvochtigheid bij opslag:	10 - 90 procent
Rack-montage:	Ja
Audio-uitgangskanalen:	2.0 kanalen
Remote (IR) uitgang:	1
Power over Ethernet (PoE):	Ja
HDMI in:	1
RS-232 ingangspoorten:	1
HDCP versie:	2.2
IR-doorvoer:	Ja
Bandbreedte:	9.2 Gbit/s
Aantal HDMI-uitgangen:	1
Operating voltage:	18 V
HDBaseT-poort:	Ja
Maximaal bereik:	100 m
Bedrijfstemperatuur (T-T):	0 - 45 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Ondersteundende kabel types:	HDMI
Extended display identification data (EDID):	Ja
HDCP-passthrough:	Ja
Stroomverbruik (TX):	4.68 W
Stroomverbruik (RX):	6.84 W