Weller WPA2N Handleiding
Weller
Soldeermachine
WPA2N
Lees hieronder de 📖 handleiding in het Nederlandse voor Weller WPA2N (4 pagina's) in de categorie Soldeermachine. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
IMPORTANT
For best performance and your safety, please read and familiarize yourself
with these instruction before using the tool.
1. Avoid dropping the tool or causing hard shocks as the ceramic burner or
fuel view window could be damaged.
2. Use an exhaust fan when using tool in an enclosed space.
3. Do not fill tool with gas or store near open flame, heater, furnace or
combustible materials.
4. Do not store in direct sunlight or anywhere that will exceed 40°C or 104°F.
5. Keep out of reach of children.
6. When not in use ensure the gas ON/OFF lever is in the OFF position.
7. Do not attempt to change soldering or hotblow tips or perform any kind of
maintenance while tool is still hot.
8. Do not misuse, abuse, alter or tamper with the tool in any way.
Only authorized people should carry out repairs.
9. Do not speed cool hot parts in water. Allow to cool naturally.
10. When operating at low temperatures, around 0°C or 32°F or lower, ignition
may be difficult. Hold handle in warm hands for a few minutes until liquid
fuel gasses. Never use an open flame or hot water to warm fuel.
11. Do not use alcohol or alcohol based cleaner on fuel window.
OPERATING PROCEDURE
1. It is most important to ensure that the exhaust opening in the tip is pointed
upwards, as above, when fitting the tip. At all times ensure the opening is
facing away from hands and combustible materials when the tool is ignited
as the exhaust temperature is very high. The tip housing can aslo reach high
temperatures. Ignition problems will result if ignition is attempted with tip
or tip housing removed.
2. Set gas control lever to 3, set gas ON/OFF
lever to ON. In cold temperature or immediately
after filling gas, it may be necessary
to use a higher setting than 3.
3. Push the ignition button slowly to ignite the tool.
4. Wait until the window at the base of the tip goes
red. If the tool fails to ignite repeat step 3.
5. Adjust tip temperature with gas control lever.
6. To turn off slide the gas ON/OFF lever to the left
until it clicks OFF.
Note, the gas control lever will turn the toolnot
off.
It is recommended to leave the gas control set at
5 if the tool is not going to be used for long
periods. This will keep the fuel wick in good full
flow condition.
SELF-IGNITING
CORDLESS PYROPEN®
WPA2N / WSTA4
GAS-FILLING
Use Weller gas refill part no T0051616099 only.
1. Check gas level through window in handle.
2. Be sure the gas ON/OFF lever is at "OFF" position.
3. Hold the Pyropen® handle with tip pointing downward and,
refill nozzle in upright position. Insert nozzle of gas container
and press down.
4. As soon as the Pyropen® is filled, gas will overflow.
5. Confirm the gas reservoir is full by checking gas level in
the sight glass.
TIP CHANGING PROCEDURE
1. Unscrew knurled tip housing nut clock-wise and remove
housing.
2. Remove old tip and postion new tip.
3. Slide housing in place and tighten housing nut.
Back off one turn then turn housing until igniter pin clicks
into slot in housing lip.
4. Position tip so that exhaust opening is facing up.
5. Tighten knurled housing nut.
G Tip
Exhaust opening F Tip housing
C Window
E Kurled nut
B Ignition button
D ON/OFF Lever
A Control Lever
1-5
Gas Lever window Handle containing butane gas
Gas refill nozzle
ACCESSORY TIPS
Soldering tips
Part No. Description
1 WPT-1 Tapered needle
2 WPT-2 Chisel
3 WPT-3 2.0 mm Ø spade
4 WPT-4 3.0 mm Ø spade
5 WPT-5 Tapered needle
6 WPT-6 Micro spade
7 WPT-7 Tapered pyramid
8 WPT-8 2.0.mm Ø, 35°, spade
9 WPT -9 3.0 mm Ø, 35°, spade
10 WPT-10 Offset tapered needle
11 WPT-11 High powered chisel, 8.0 mm width
12 WPT-12 High powered round head needle,
3.0 mm Ø
13 WPT-13 High powered long taper chisel,
5.0 mm width
14 WPT-14 8.4 mm Ø, Tip adapter
(with thread M4 e.g. for hot-knife)
Hot blow nozzles
Part No. O.D. (mm) I.D. (mm)
15 WHC-50 2.5 1.5
16 WHC-51 4.25 3.3
17 WHC-52 5.7 4.9
18 WHC-53 8.0 7.4
19 T0051615999 Shrinking attachment,
radius 6.0 mm/8.0mm
20 T0051637599 Ejector unit
HOW TO CHANGE BURNER / EJECTOR
To remove
Change ejector unit when gas does not flow,
ceramic burner is broken or used up after certain
time of use, etc.
1. Loosen knurled nut to remove tip and tip
housing.
2. Insert the accessory bar into the hole at ejector
turn clockwise. (Be careful not to damage the
white ceramic portion of the unit!)
To mount
1. Mount new ejector in the place of the removed
one and tighten with the accessory bar.
2. Mount the tip and tip housing and tighten
knurled nut.
HOW TO USE AS TORCH
1. To remove t he soldering t ip and t ip recept ac le,
undo the knurled nut.
2. Replace the soldering tip with the hot air nozzle. The ignition
system is the same as for the soldering iron.
SPECIFICATIONS
Length including soldering tip 265 mm / 10- 7/16"
Weight including gas filling 117 grams / 4.1 oz.
Temperature values Soldering Iron
250°-500°C / 482°-932°F
Hot Blow
650°C / 1202°F
Burning time per gas filling 2 hours with gas control lever
set at 2.
Filling quantity 28 cc / 1.71 cu. in.
If the tool is normally used in places of extreme temperature, either hot or
cold, or at high altitude, ignition may be difficult. This is due to the extremes
affecting the gas pressure. Gas control settings will also be affected and
will vary from those under normal conditions. If difficulties are experienced
please contact your Weller Tools Service Centre for advice.
GERMANY
Weller Tools GmbH
Carl-Benz-Str. 2
74354 Besigheim
Phone: +49 (0) 7143 580-0
Fax: +49 (0) 7143-580-108
USA
Apex Tool Group, LLC
1000 Lufkin Road
Apex, NC 27539
Phone: +1 (866) 498-0484
Fax: +1 (919) 387-2639
AUSTRALIA
Apex Tool Group Pty Ltd
P.O. Box 366
519 Nurigong Street
Albury, N.S.W. 2640
Phone: +61 (02) 6058-0300
Fax: +61 (02) 6021 7403
Email: apextoolaus@apextoolgroup.com
Web: apextoolgroup.com.au
1. Loosen knurled nut to remove tip and tip
housing.
2. Replace with hot blolw nozzle.
Ignition is the same as for soldering.
HOW TO USE THE HOT BLOW NOZZLE TROUBLE-SHOOTING
Problem Possible reason Correction
Does not light. Empty tank. Refill with butane gas.
Clogged ejector. Replace with new
ejector.
Gas pressure too high Slide control lever to
or too low. lower or higher position.
Tip does not Used-up catalyst. Replace with new tip.
heat up.
Insufficient gas pressure Refill with butane gas.
Clogged ejector. Replace with new
ejector.
© Copyright 2019 Apex Tool Group LLC.
Product specificaties
| Merk: | Weller |
| Categorie: | Soldeermachine |
| Model: | WPA2N |
Heb je hulp nodig?
Als je hulp nodig hebt met Weller WPA2N stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Soldeermachine Weller
14 November 2024
5 November 2024
5 November 2024
6 Januari 2024
6 Januari 2024
6 Januari 2024
18 December 2023
9 Augustus 2023
9 Juli 2023
1 Juli 2023
Handleiding Soldeermachine
- Soldeermachine Basetech
- Soldeermachine Denon
- Soldeermachine Einhell
- Soldeermachine Ferm
- Soldeermachine Gude
- Soldeermachine Gys
- Soldeermachine Holzmann
- Soldeermachine HQ
- Soldeermachine Maestro
- Soldeermachine Mercury
- Soldeermachine Milwaukee
- Soldeermachine Monacor
- Soldeermachine Nedis
- Soldeermachine Parkside
- Soldeermachine Powerfix
- Soldeermachine Powerplus
- Soldeermachine Ryobi
- Soldeermachine Sievert
- Soldeermachine Silverline
- Soldeermachine Telwin
- Soldeermachine Toolcraft
- Soldeermachine Trotec
- Soldeermachine Velleman
- Soldeermachine Westfalia
- Soldeermachine Ozito
- Soldeermachine Steren
- Soldeermachine Cocraft
- Soldeermachine Truper
- Soldeermachine Fieldmann
- Soldeermachine RIDGID
- Soldeermachine Craftsman
- Soldeermachine Yato
- Soldeermachine Cigweld
- Soldeermachine Epcom
- Soldeermachine Uten
- Soldeermachine CFH
- Soldeermachine Edsyn
- Soldeermachine Mag-Torch
- Soldeermachine UNIMIG
- Soldeermachine Ersa
- Soldeermachine Portasol
- Soldeermachine JBC
- Soldeermachine Hakko
- Soldeermachine Fixpoint
- Soldeermachine Stamos
Nieuwste handleidingen voor Soldeermachine
3 December 2024
20 November 2024
19 November 2024
19 November 2024
16 November 2024
13 November 2024
13 November 2024
13 November 2024
12 November 2024
5 November 2024