Vivanco UR 44 Handleiding

Vivanco Afstandsbediening UR 44

Lees hieronder de 📖 handleiding in het Nederlandse voor Vivanco UR 44 (19 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/19

Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Tel:+49(0)

4102231235, Fax: +49(0)4102 31444, e-Mail: 1hotline@vivanco.de

UR 44+4 Universal Controller

(GB) Instructions

UR 44+4 Universal remote control

To control almost all TV sets, satellite receivers, DVD

players and recorders, CD players and other infrared-

controllable devices.

1 Important – please read

The Vivanco UR 44+4 is pre-programmed to control up to 8

devices, replacing damaged or lost original remote controls.

It controls the basic functions of the devices for which it has

been set and is not designed to replace all the functions of

the original remote controls. In order to be able to control

your devices, you must set the remote control as described

in the section "Code entry".

2 Inserting batteries

Open the battery compartment on the underside of the UR

44+4. To do so, lightly press the locking mechanism of the

battery compartment upwards, then insert 2 new AAA

alkaline batteries. Make sure that the polarity is correct: the

"+" and "-" markings on the batteries and in the

compartment must match. To check functionality, press the

PWR button. If everything is correct the red lamp flickers

when the button is pressed.

3 Code entry

The correct control codes can be set via direct code entry or

automatic code search.

Direct code entry

Using the enclosed code list, note the possible codes for the

device and the brand.

To set your TV set, proceed as follows:

1. Using the enclosed code list, find the codes to

control your brand of television (TV). It is

Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Tel:+49(0)

4102231235, Fax: +49(0)4102 31444, e-Mail: 2hotline@vivanco.de

possible that there are several suitable codes

and you should find out the most suitable.

2. Switch on a program on your TV.

3. Press the button, hold it down and at theSET

same time press a device button, e.g. , untilTV*)

the red lamp comes on.

4. Then enter one of selected three-digit codes.

Key 0: please press key 10.

5. When the first and second number buttons are

pressed the lamp goes out briefly; when the third

is pressed it stays out.

6. Try out the functions. If everything is okay, you

can set the remote control as described in steps

1 to 5 for other devices. If it is not okay, try

another code for the same brand.

The letters on the device buttons TV1/TV2*), SAT1/SAT2*),

DVD1/DVD2*), VCR1/VCR2*) are for your orientation only.

You can set each type of device under any of the buttons.

If you do not find a suitable code for a device, look for it

using the code search.

*): All 4 keys of the device can be assigned twice so that 8

different devices can be controlled altogether. If you press a

key once according to these instructions you can enter a

device code for the first assignment or control the first

device. If you press a key twice within one second you can

set the key for a second device, or control a second device

via the key.

Code search

To control a TV:

1. Switch on a program on your TV (on the TV

itself or with the original remote control).

2. Press the button, hold it down and at theSET

same time press a device button, e.g. , untilTV*)

the red lamp comes on.

3. Then press the button again briefly, theSET

lamp starts to blink.

Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Tel:+49(0)

4102231235, Fax: +49(0)4102 31444, e-Mail: 3hotline@vivanco.de

4. Press the button approx. every 2 seconds.PWR

5. When the TV switches itself off, briefly press the

device button ( ) to store the code found.TV*)

6. The lamp goes out and the search is ended.

7. Try out the functions. If everything is okay, you

can set the remote control as described in steps

1 to 6 for other devices. Then press the device

buttons , or instead of .SAT*) DVD*) VCR*) TV*)

If it is not okay, continue searching as described

in 1 to 6.

Automatic code search

To control a TV:

1. Switch on a program on your TV (on the TV

itself or with the original remote control).

2. Press the device button with which you want to

control a device, e.g. .TV*)

3. Then press the button for approx. 5SET

seconds until the red lamp comes on.

4. Release the button and point the URSET

44+4at the device to be controlled. The UR 44+4

then begins to emit a test signal about every 2

seconds.

5. When the TV switches itself off, briefly press the

SET button to store the code found.

6. The lamp goes out and the search is ended.

7. Try out the functions. If everything is okay, you

can set the remote control as described in steps

1 to 6 for other devices. Then press the device

buttons , or instead of .SAT*) DVD*) VCR*) TV*)

If it is not okay, continue searching as described

in 1 to 6.

4 Controlling devices

To control a specific device, first press a device button, e.g.

TV*) to control the TV set and then the required function

buttons.

Product specificaties

Merk:	Vivanco
Categorie:	Afstandsbediening
Model:	UR 44
Kleur van het product:	Zwart, zilver
Ingebouwd display:	Nee
Gewicht:	- g
Ondersteund aantal accu's/batterijen:	2
Maximumbereik:	- m
Oplaadbaar:	Nee
Input type:	Drukknopen
juiste gebruik afstandsbediening:	DVD/Blu-ray, SAT, TV
Batterijtechnologie:	Alkaline
Type batterij:	AAA
Number of devices supported:	4