Vivanco UR Z2 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Vivanco UR Z2 (36 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/36
GB Operating instructions 2 – 3
D Bedienungsanleitung 4 – 5
F Mode d’emploi 6 – 7
E Manual de Instrucciones 8 – 9
NL Gebruiksaanwijzing 10 – 11
PL Instrukcja obsługi 12 – 13
S Bruksanvisning 14 – 15
RUS
Руководство по эксплуатации 16 – 17
Universal TV- DVB Controller UR Z2
EDP-No.: 34873
Seite/ Page
BDA 34873-Rev-RZ_Layout 1 21.06.13 09:14 Seite 1
Universal TV- DVB Controller UR Z2
Before you start using the device, please first read through the safety information and this
operating instruction very carefully. Only then you can use all the functions safely and reli-
ably. Please maintain the operating instruction well and pass on to possible other owners.
Intended use
Universal remotes replace original remote controls etc. of consumer electronics devices. The device is
meant for sole use in private households and may not be used for commercial purposes. Any other use
is not deemed as intended use and may lead to material damages or even to personal injuries.
The manufacturer does not assume any liability for damages that have occurred due to unintended use.
Battery/rechargeable battery safety
Please read these instructions very carefully. Disregarding these instructions can cause
damages/injuries and possibly even an explosion of batteries/rechargeable batteries! Do not short-
circuit the contacts, for example by common storage with metallic objects. Do not expose batteries/
rechargeable batteries to long periods of direct sunlight or heat. Do not throw batteries/rechargeable
batteries into the fire. Do not open batteries/rechargeable batteries, they do not contain any parts that
need to be maintained. Only replace batteries/rechargeable batteries with the same type or with an
equivalent recommended by the manufacturer. Accumulators only: For charging accumulators, do only
use the charging functions integrated in the device or any other suitable chargers. Never charge batteries.
Inserting the batteries
Open the battery flap on the back of the remote control, press the tongue lightly downwards, then insert
2 alkaline AA batteries. Check that the polarity markings on the batteries and in the battery compartment
are correctly lined up (+=+), then close the flap carefully. – Always use undamaged batteries.
Adapting to appliances
In order to control e.g. your TV or DVB you must adapt or set the remote control to it. There are two
ways of doing so: direct control code entry or code search.
Direct control code entry using the enclosed list
Example: setting to control a Panasonic television set:
1. The attached list gives, for example, the Panasonic Code 0158. Please make sure you have
selected the correct list for television sets (TV).
2. To prepare code entry, press the SET button, keep it pressed and then press the required appliance
button, e.g. TV, additionally until the lamp (LED) lights constantly.
3. Then press the number buttons (e.g. 0158) in sequence.
4. Once the numbers have been entered the lamp goes out and the remote control is ready to control
your appliance.
5. Finally, test the control code setting by trying to control (in this example) your television set. If it does
not work at all or not correctly try a different code from the list or the code search (see below). You can
terminate the mode by pressing any device button.
Code search
If the brand of your appliance is not in the list or none of the codes given fits, we recommend a code
search.
Manual code search
1. Switch on the appliance to be controlled. Program is running.
2. To prepare code search, press the SET button, keep it pressed and then press the required
appliance button, e.g. TV, additionally until the lamp (LED) lights constantly.
3. Then point the remote control at the appliance to be controlled.
4. Briefly press the SET button once. The lamp (LED) blinks.
5. Press the ON/OFF (appliance on/off) button repeatedly for testing the next code, approx. every
1,5 seconds, until the appliance, e.g. your TV reacts by power off. - If your appliance has switched itself
off you must switch it back on again, e.g. on the appliance or with the original remote control, to continue
searching. - When your appliancereacts you can also try out other buttons without interrupting the
search. If some buttons do not work properly, simply continue searching with ON/OFF.
6. When your appliance reacts correctly, press the appliance button, e.g. TV, and end the search. The
lamp (LED) goes out. - The UR Z2 continues with the search at the point where you interrupted it. The
code last entered remains stored. The search stops after approx. 30 seconds of inactivity.
2
GB
BDA 34873-Rev-RZ_Layout 1 21.06.13 09:14 Seite 2
Automatic code search
Your remote control finds the correct settings almost automatically in seconds:
1. Switch on the appliance to be controlled. A channel number, for example, appears in the display of
your DVB.
2. To start the code search, press the required appliance button, e.g. DVB briefly.
3. Then press SET for about 5 seconds until the lamp (LED) starts to blink.
4. Then point the remote control at the appliance to be controlled while the remote control emits a
different ON/OFF signal every second.
5. When your appliance reacts, press SET within 1-2 seconds, to end the search. – If you
ended the
search too late, continue to search using the Manual Code Search (see above).
6. Finally, test the control code setting by trying to control, for example, your DVB appliance. If it does
not work correctly, please try the code search again. The code search then begins with the next code in
the sequence. - Remember to switch your appliance, e.g. DVB, back on again if you wish to continue
searching.
Code identification
You can read off the 4-digit codes you have set at any time:
1. Press the appliance button of the appliance which code you want to read off, e.g. TV.
2. Press the SET button and 1,2,3,4 regardless of the part of the code you want to read off. For exam-
ple, if you press SET+1 after TV and the code 0158 (in this example) has been set, the lamp does not
blink after SET+1 is released to show that the thousands 25figure is 0. All you have to do is count. After
SET+2 is released the lamp blinks once to show that the hundred figure is 1.The ten figure is indicated
after SET+3 is released, e.g. it blinks 5 times for the 5 in 158. The one figure is indicated after SET+4 is
released, e.g. it blinks 8 times for the 8 in 0158. - Please open the battery compartment and write down
the found codes, for later use, onto the sticker placed at the innerside of the compartment door.
Operation
You operate your appliances basically in exactly the same way as if you were using the original remote
controls, except that you must first press an appliance button (TV, DVB, etc.) to control the required
appliance. As the symbols on the UR Z2 could differ from those on the original remote controls you may
have to try out all the buttons in order to find the functions.
Punch through
If certain control codes e.g. for controlling DVB, don´t contain volume and mute key functions, then the
controller controls TV volume and mute automatically.
Specifications
Batteries: 2x AA batteries, NiMH, rechargeable can also be used
Range: max. 7 m
Not for 400 kHz equipment
Hereby Vivanco GmbH declares that UR Z2 is in conformity with the
fundamental requirements and other relevant regulations of the directive 2004/108/EU.
Disposal of the device
This device may not be disposed along with household waste. Please hand it over to a col-
lection point for electrical devices of your area or your district. Thus it will be guaranteed that
the old devices are recycled properly and economically and potential environmental and
health hazards are avoided.
Recycle Batteries
Rechargeable and non-rechargeable batteries shall not be disposed with household waste.
You are legally obligated to return used batteries, so that a professional, environmentally
safe disposition is assured. Please take them to a municipal collection point or retailer.
Please only hand in batteries and accumulators that are completely discharged.
The packing should be supplied to re-use. Please do not throw it into
household waste and handle it in conformity with local disposal rules.
3
Pb/Cd/Hg
BDA 34873-Rev-RZ_Layout 1 21.06.13 09:14 Seite 3


Product specificaties

Merk: Vivanco
Categorie: Afstandsbediening
Model: UR Z2
Kleur van het product: Zilver
Ingebouwd display: Nee
Gewicht: - g
Maximumbereik: 7 m
Oplaadbaar: Nee
Input type: Drukknopen
juiste gebruik afstandsbediening: TV, TV set-top box
Batterijen inbegrepen: Nee
Type batterij: AA

Heb je hulp nodig?

Als je hulp nodig hebt met Vivanco UR Z2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Afstandsbediening Vivanco

Handleiding Afstandsbediening

Nieuwste handleidingen voor Afstandsbediening