Vivanco UR 1200 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Vivanco UR 1200 (36 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/36
TITAN UNIVERSAL REMOTE CONTROLS UR 1200
(GB) Instructions ► 2
(D) Bedienungsanleitung ► 5
(F) Notice d’emploi ► 8
(E) Instrucciones para el uso ► 11
(I) Istruzioni per l’uso ► 15
(NL) Gebruiksaanwijzing ► 18
(PL) Instrukcja obsługi ► 21
(P) Manual de instruções ► 24
(S) Bruksanvisning ► 28
(RUS) Руководство по
эксплуатации ► 30
(CZ) Návod k obsluze ► 33
(GB) Instructions
Inserting the
batteries
Open the battery com-
partment on the under-
side of the remote..
Then insert 2 AAA bat-
teries. Make sure that
the polarity is correct:
the "+" and "-" mark-
ings on the batteries
and in the compart-
ment must match.
- To check functional-
ity, press the but-
ton. If everything is
correct the red lamp
flickers when the button is pressed.
Adapting to appliances
In order to control your appliances you must ad-
apt or set the remote control to them. There are
two ways of doing so:
Direct control code entry using the enclosed
list
Example: setting to control a Panasonic televi-
sion set:
1. The enclosed list
gives, for example,
the Panasonic Code
436.
- Please make sure you
have selected the cor-
rect list for television
sets (TV).
2. To prepare code
entry, keep the OK
button and the TV
button pressed simul-
taneously(!) until the
lamp (LED) lights
constantly.
3. Then enter the code
numbers as follows:
4. 1st number of code
(hundreds): Press the
VOLUME+ button- 4
times for the 4 of 36. 4
Press as often as the
number indicates.
(1=once, 2 = twice,
etc.)
5. 2nd number of code (tens): Press the
VOLUME- button 3 times for the 3 of 4 6.3
6. 3rd number of code (ones): Press the
CH/SKIPΔ 6 button 6 times for the of 43 .6
7. Finally, press the button again briefly. The OK
lamp ( goes out. LED)
- To enter a 0, do not press any button.
- If lamp flashes twice code was not accepted
Vivanco GmbH, D-22926 Ahrensburg, E-Mail: , Helpline: +49 (0) 4102 231135hotline@vivanco.de 2
and code input can be started again.
8. Then test the control code setting by trying to
control (in this example) your television set. If
it does not work at all or not correctly try a dif-
ferent code from the list or code search (see
below).
9. To make the setting for a DVB (SAT, CBL), re-
ceiver or a cable box, press the SAT/DVB
(SAT, CBL) button instead of TV and enter a
DVB (SAT, CBL) code accordingly.
- You terminate the mode by pressing any
device button or by code input interruption of
more than 10 seconds.
Code search
If the brand of your appliance is not in the list or
none of the codes given fits, we recommend a
code search.
Manual code search
1. Switch on the appliance to be controlled. Pro-
gram is running.
2. To prepare code search, press the button OK
and the appliance button, e.g. TV, simultan-
eously until the lamp (LED) lights constantly.
3. Then point the remote control at the appli-
ance to be controlled.
4. Briefly press the ON/OFF button once.
The lamp (LED) blinks.
5. Press the ON/OFF button about any 1
second so often until the appliance, e.g. your
TV reacts by power off.
- You can invert search direction by pressing
the button and then again.OK
- If your appliance has switched itself off, you
must switch it back on again, e.g. on the appli-
ance or with the original remote control, to con-
tinue searching.
- When your appliance reacts you can also try
out other buttons without interrupting the
search. If some buttons do not work properly,
simply continue searching by pressing ON/OFF
again.
6. When your appli-
ance reacts cor-
rectly, press the ap-
pliance button, e.g.
TV for end of
searching and sav-
ing of found code.
The lamp (LED)
goes out.
- The last code
entered remains
stored. The search
stops after approx. 30
seconds of inactivity.
Automatic code
search
1. Switch on the appli-
ance to be con-
trolled. Program is
running.
2. To start the code
search, press the
OK button and the
Vivanco GmbH, D-22926 Ahrensburg, E-Mail: , Helpline: +49 (0) 4102 231135hotline@vivanco.de 3


Product specificaties

Merk: Vivanco
Categorie: Afstandsbediening
Model: UR 1200
Kleur van het product: Zwart
Aan/uitschakelaar: Ja
Ondersteund aantal accu's/batterijen: 2
Teletext: Nee
Backlight toetsen: Nee
Batterijen inbegrepen: Nee
Type batterij: AAA
Cursortoets: Ja

Heb je hulp nodig?

Als je hulp nodig hebt met Vivanco UR 1200 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Afstandsbediening Vivanco

Handleiding Afstandsbediening

Nieuwste handleidingen voor Afstandsbediening