Vivanco UR 1300 Handleiding

Vivanco Afstandsbediening UR 1300

Lees hieronder de 📖 handleiding in het Nederlandse voor Vivanco UR 1300 (47 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/47

TITAN UNIVERSAL REMOTE CONTROLS UR 1250 - UR 1300

(GB) Instructions ► 2

(D) Bedienungsanleitung ► 4

(F) Notice d’emploi ► 8

(E) Instrucciones para el uso ► 11

(I) Istruzioni per l’uso ► 14

(NL) Gebruiksaanwijzing ► 17

(PL) Instrukcja obsługi ► 20

(P) Manual de instruções ► 23

(DK) Betjeningsvejledning ► 26

(S) Bruksanvisning ► 29

(FIN) Käyttöohje ► 32

(RUS) Руководство по

эксплуатации ► 35

(GR) Οδηγίες χρήσης ► 37

(TR) Kullanma talimatı ► 39

(CZ) Návod k obsluze ► 41

(SK) Návod na obsluhu ► 43

(H) Kezelési útmutató ► 45

(GB) Instructions

Inserting the batteries

Open the battery compart-

ment on the underside of

the remote.. Then insert 2

AAA batteries. Make sure

that the polarity is correct:

the "+" and "-" markings on

the batteries and in the

compartment must match.

- To check functionality,

press the button. If POWER

everything is correct the red

lamp flickers when the but-

ton is pressed.

Adapting to appliances

In order to control your appliances you must adapt or

set the remote control to them. There are two ways of

doing so:

Direct control code entry

Example: Setting to control a Panasonic television

set:

1. The attached list gives, for example, the

Panasonic Code .436

- Please make sure you have selected the code from

correct list for television sets (TV).

2. Press button and a appliance button, e.g. OK

TV, simultaneously until the

lamp (LED) lights constantly.

3. Then press number but-

tons (e.g. ) in sequence.4 3 6

4. Once the numbers have

been entered the lamp goes

out and the remote control is

ready to control your appli-

ance.

5. Finally, test the control

code setting by trying to con-

trol, in this example, your tele-

vision set. If it does not work at

all or not correctly try a differ-

ent code from the list or the

code search (see below).

To set the remote control for

other appliances, proceed in

the same way. Instead of the

TV appliance button, press

another button e.g. SAT DVB /

(SAT, DECODER) or

DVD BLU RAY/ (UR 1300

only).

- You terminate the mode by

pressing any device button or

by code input interruption of

more than 10 seconds.

If lamp flashes twice code was not accepted and code

input can be started again.

Code search

If the brand of your appliance is not in the list or none of

the codes given fits, we recommend a code search.

Vivanco GmbH, D-22926 Ahrensburg, E-Mail: , Helpline: +49 (0) 4102 231135hotline@vivanco.de 2

Manual code search

1. Switch on the appliance to

be controlled. Program is run-

ning.

2. To prepare code search,

press the button and the OK

appliance button, e.g. , sim-TV

ultaneously until the lamp

(LED) lights constantly.

3. Then point the remote con-

trol at the appliance to be con-

trolled.

4. Briefly press the ON/OFF

POWER button once. The

lamp (LED) blinks.

5. Press the ON/OFF

POWER button about any 1

second so often until the appli-

ance, e.g. your TV reacts by

power off.

- You can invert search direc-

tion by pressing the button OK

and then again.POWER

- If your appliance has

switched itself off, you must

switch it back on again, e.g.

on the appliance or with the

original remote control, to

continue searching.

- When your appliance reacts you can also try out other

buttons without interrupting the search. If some buttons

do not work properly, simply continue searching by

pressing ON/OFF again. POWER

6. When your appliance reacts correctly, press

the appliance button, e.g. TV for end of searching and

saving of found code. The lamp (LED) goes out.

- The last code entered remains stored. The search

stops after approx. 30 seconds of inactivity.

Automatic code search

1. Switch on the appliance to

be controlled. Program is run-

ning.

2. To start the code search,

press the button and the OK

appliance button, e.g. , TV

simultaneously for more than

3 seconds until the lamp

(LED) goes off briefly.

3. Then point the remote

control at the appliance to be

controlled while the remote

control emits a different

ON/OFF signal every 1-2

seconds.

- You can reverse search dir-

ection at any time by pressing

OK button.

4. When your appliance re-

acts, press any button except

OK within 1-2 seconds, to

end the search and save

code..

– If you ended the search too

late, continue to search using

the Manual Code Search

(see above).

5. Finally, test the control code setting by trying

to control, for example, your DVD appliance (UR 1300

only). If it does not work correctly, please try the code

search again. The code search then begins with the

found code in the sequence.

- Remember to switch your appliance, e.g. DVD, back

on again if you wish to continue searching.

Vivanco GmbH, D-22926 Ahrensburg, E-Mail: , Helpline: +49 (0) 4102 231135hotline@vivanco.de 3

Product specificaties

Merk:	Vivanco
Categorie:	Afstandsbediening
Model:	UR 1300
Kleur van het product:	Zwart
Aan/uitschakelaar:	Ja
Ondersteund aantal accu's/batterijen:	2
Teletext:	Ja
Batterijen inbegrepen:	Nee
Type batterij:	AAA
Cursortoets:	Ja