Vivanco PRO UR 3 TTP Handleiding

Vivanco Afstandsbediening PRO UR 3 TTP

Lees hieronder de 📖 handleiding in het Nederlandse voor Vivanco PRO UR 3 TTP (27 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/27

Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Tel:+49(0)

4102231235, Fax: +49(0)4102 31444, e-Mail: 1hotline@vivanco.de

Universal Controllers

PRO UR 3 TTP (3in1)

(GB) Instructions for

Universal remote control

To control almost all TV sets, satellite receivers, DTT set top

boxes, DVD players and recorders, CD players and other

infrared-controllable devices.

1 Important – please read

The Vivanco PRO UR ...is pre-programmed to control up to

3 devices, replacing damaged or lost original remote

controls. It controls the basic functions of the devices for

which it has been set and is not designed to replace all the

functions of the original remote controls. In order to be able

to control your devices, you must set the remote control as

described in the section "Code entry".

2 Battery Replacement

Open the battery compartment on the underside of the PRO

UR . To do so, lightly press the locking mechanism (left side

of battery drawer) of the battery compartment upwards, then

ireplace the CR 2032 lithium cell. Make sure that the polarity

is correct. To check functionality, press the button. If PWR

everything is correct the red lamp flickers when the button is

pressed.

3 Code entry

The correct control codes can be set via direct code entry or

automatic code search.

Direct code entry

Using the enclosed code list, note the possible codes for the

device and the brand.

To set your TV set, proceed as follows:

1. Using the enclosed code list, find the codes to

control your brand of television (TV). It is

possible that there are several suitable codes

and you should find out the most suitable.

2. Switch on a program on your TV.

Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Tel:+49(0)

4102231235, Fax: +49(0)4102 31444, e-Mail: 2hotline@vivanco.de

3. Press the button, hold it down and at the SET

same time press a device button, e.g. , until TV

the red lamp comes on.

4. Then enter one of selected three-digit codes

5. When the first and second number buttons are

pressed the lamp goes out briefly; when the third

is pressed it stays out.

6. Try out the functions. If everything is okay, you

can set the remote control as described in steps

1 to 5 for other devices. If it is not okay, try

another code for the same brand.

The letters on the device buttons are for your TV, SAT, AUX

orientation only. You can set each type of device under any

of the buttons.

If you do not find a suitable code for a device, look for it

using the code search.

Code search

To control a TV:

1. Switch on a program on your TV (on the TV

itself or with the original remote control).

2. Press the button, hold it down and at the SET

same time press a device button, e.g. , until TV

the red lamp comes on.

3. Then press the button again briefly, the SET

lamp starts to blink.

4. Press the button approx. every 2 seconds. PWR

5. When the TV switches itself off, briefly press the

device button ( ) to store the code found. TV

6. The lamp goes out and the search is ended.

7. Try out the functions. If everything is okay, you

can set the remote control as described in steps

1 to 6 for other devices. Then press the device

buttons , or instead of . If it is not SAT AUX TV*)

okay, continue searching as described in 1 to 6.

Automatic code search

To control a TV:

1. Switch on a program on your TV (on the TV

itself or with the original remote control).

Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Tel:+49(0)

4102231235, Fax: +49(0)4102 31444, e-Mail: 3hotline@vivanco.de

2. Press the device button with which you want to

control a device, e.g. . TV

3. Then press the button for approx. 5 SET

seconds until the red lamp comes on.

4. Release the button and point the PRO UR SET

at the device to be controlled. The PRO UR

..then begins to emit a test signal about every 2

seconds.

5. When the TV switches itself off, briefly press the

SET button to store the code found.

6. The lamp goes out and the search is ended.

7. Try out the functions. If everything is okay, you

can set the remote control as described in steps

1 to 6 for other devices. Then press the device

buttons , or instead of . If it is not SAT AUX TV

okay, continue searching as described in 1 to 6.

4 Controlling devices

To control a specific device, first press a device button, e.g.

TV to control the TV set and then the required function

buttons.

Volume control

With some devices that have no volume control, such as

video recorders, DVD players, etc. you can control the

volume of the TV without having to press the TV button first

(Punch Through).

(D) Bedienungsanleitung

Universalfernbedienung

zur Steuerung fast aller Fernsehgeräte, Satreceiver, DVB-T

Set Top Boxen, DVD Player und Recorder, CD Player und

anderer infrarotsteuerbarer Geräte

1 Wichtig – Bitte lesen

Die Vivanco PRO UR .....ist vorprogrammiert für die

Steuerung von bis zu 3 Geräten, um beschädigte oder

verlorene Originalfernbedienungen zu ersetzen. Sie steuert

die Grundfunktionen der Geräte für die sie eingestellt wurde

und wurde nicht dafür entwickelt, alle Funktionen der

Originalfernbedienungen zu ersetzen. Sie müssen die

Product specificaties

Merk:	Vivanco
Categorie:	Afstandsbediening
Model:	PRO UR 3 TTP
Kleur van het product:	Blauw
Ingebouwd display:	Nee
Gewicht:	- g
Ondersteund aantal accu's/batterijen:	3
Teletext:	Ja
Maximumbereik:	- m
Input type:	Touchscreen/drukknoppen
juiste gebruik afstandsbediening:	DVD/Blu-ray, SAT, TV, VCR
Batterijen inbegrepen:	Ja
Type batterij:	CR2032
Number of devices supported:	3