Tripp Lite PDUMV16HV Handleiding

Tripp Lite Stekkerdoos PDUMV16HV

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite PDUMV16HV (28 pagina's) in de categorie Stekkerdoos. Deze handleiding was nuttig voor 53 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/28

Owner’s Manual

Metered Rack PDU

Models: PDUV30HV, PDUMV30, PDUMV16HV,

PDUMV20HV, PDUMV30HV

(Series Number: AGIB6672, AGPD6673, AGPD6674, AGPD6675)

Español 6 • Français 11 • Русский 16 • Deutsch 21

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

18-11-318-933312.indb 1 3/20/2019 1:22:51 PM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be

followed during the installation, operation and storage of this

product. Failure to heed these instructions and warnings will void

the product warranty.

Important Warnings

• The PDU provides the convenience of multiple outlets, but DOES NOT provide surge or

line noise protection for connected equipment.

• The PDU is designed for indoor use only, in a controlled environment, away from

excess moisture, temperature extremes, conductive contaminants, dust or direct

sunlight.

• The PDU must be installed by a qualiﬁed technician only.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Install in accordance with National Electrical Codes. Be sure to use the proper over

current protection for the installation, in accordance with the plug rating/equipment

rating as follows:

Model Series Number Overcurrent Protection

PDUV30HV AGIB6672 30A

PDUMV30 AGPD6673 30A

PDUMV16HV, PDUMV20HV AGPD6674 20A

PDUMV30HV AGPD6675 30A

• Short-circuit backup protection and overcurrent protection is provided by the building

installation.

• The electrical outlets supplying power to the equipment should be installed near the

equipment and easily accessible.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters

that eliminate the connection to ground.

• The plug on the power supply cord is intended to serve as the disconnect device.

Be sure that the socket-outlet is installed near the equipment and is made easily

accessible.

• Never attempt to install electrical equipment during a thunderstorm.

• The power requirement for each piece of equipment connected to the PDU must not

exceed the individual outlet’s load rating.

• The total power requirement for equipment connected to the PDU must not exceed the

maximum load rating for the PDU.

• Do not attempt to modify the PDU, input plugs or power cables.

• Do not drill into or attempt to open any part of the PDU housing. There are no user-

serviceable parts inside.

• Do not attempt to use the PDU if any part of it becomes damaged.

18-11-318-933312.indb 2 3/20/2019 1:22:51 PM

Important Safety Instructions

Installation

Note: The user must determine the ﬁtness of hardware and procedures before mounting. The PDU and included

hardware are designed for common rack and rack enclosure types and may not be appropriate for all applications.

1A 0U Rack Conﬁguration (Mounting

Brackets). Prior to installation,

determine the rack location in which

the PDU is to be installed. Attach the

mounting brackets to the back of the

PDU as shown, using the included

screws. To assist with proper positioning,

the brackets have four screw holes each;

make sure that the same two holes are

used to attach each bracket to the PDU.

After attaching the brackets, position the

PDU in the rack and mount it by installing

four user-supplied screws through the

brackets into the rack.

1B 0U Rack Conﬁguration (Mounting

Buttons). Attach the included mounting

buttons to the PDU. Position the PDU as

desired in the rack enclosure, align the

buttons with the rack mounting slots,

and slide the PDU into position.

1C Under-Counter Conﬁguration. The PDU

may be installed under a counter using

the included mounting brackets. Attach

the mounting brackets to the back of

the PDU as shown in STEP 1A. Secure

the PDU to the underside of the counter

by installing two user-supplied screws

through each bracket into the counter.

• Use of this equipment in life support applications where failure of this equipment

can reasonably be expected to cause the failure of the life support equipment or to

signiﬁcantly affect its safety or effectiveness is not recommended.

18-11-318-933312.indb 3 3/20/2019 1:22:51 PM

Product specificaties

Merk:	Tripp Lite
Categorie:	Stekkerdoos
Model:	PDUMV16HV
Kleur van het product:	Zwart
Gewicht:	2410 g
Breedte:	57.2 mm
Diepte:	95.2 mm
Hoogte:	1619.2 mm
Snoerlengte:	3 m
Gewicht verpakking:	3580 g
Breedte verpakking:	129.5 mm
Diepte verpakking:	1661.2 mm
Hoogte verpakking:	73.7 mm
Materiaal behuizing:	Metaal
LED-indicatoren:	Ja
Beeldscherm:	LED
Land van herkomst:	China
Afmetingen verpakking (BxDxH):	76 x 127 x 1648 mm
Certificering:	IEC 60950-1, GOST
Duurzaamheidscertificaten:	RoHS
Afmetingen (B x D x H):	57 x 95 x 1620 mm
Montage:	Verticaal
Stekker:	IEC309
(Buitenste) hoofdverpakking hoogte:	177.8 mm
(Buitenste) hoofdverpakking breedte:	419.1 mm
(Buitenste) hoofdverpakking brutogewicht:	23040 g
(Buitenste) hoofdverpakking lengte:	1668.8 mm
Hoeveelheid per (buitenste) hoofdverpakking:	6 stuk(s)
Rackcapaciteit:	0U
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
GTIN (EAN/UPC)-nummer (buitenste) hoofdverpakking:	10037332182873
Aantal AC uitgangen:	38 AC-uitgang(en)
Nominale input voltage:	200-240 V
Stopcontacttypes:	C13 coupler,C19 coupler
Stroom (max.):	16 A
PDU types:	Gemeten
Netspanning, in bedrijf:	200-240 V
Output-aansluitingen:	32 x C13 & 6 x C19