Tripp Lite PDUMH30HV Handleiding

Tripp Lite Stekkerdoos PDUMH30HV

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite PDUMH30HV (40 pagina's) in de categorie Stekkerdoos. Deze handleiding was nuttig voor 72 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/40

Owner’s Manual

Metered Rack PDUs

Low-Voltage Models: PDUMH15, PDUMH15S, PDUMH20

High-Voltage Models: PDUMH20HV, PDUMH30HV, PDUMH32HV

Español 9 • Français 17 • Русский 25 • Deutsch 33

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

18-11-317-933059.indb 1 2/20/2019 4:26:36 PM

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be

followed during the installation, operation and storage of this product.

Failure to heed these instructions may affect your warranty.

Important Warnings

• The PDU provides the convenience of multiple outlets, but DOES NOT provide surge or line

noise protection for connected equipment.

• The PDU is designed for indoor use only, in a controlled environment, away from excess

moisture, temperature extremes, conductive contaminants, dust or direct sunlight.

• Keep indoor ambient temperature between 32°F and 122°F (0°C and 50°C).

• The PDU must be installed by a qualified technician only.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Install in accordance with National Electrical Code standards. Be sure to use the proper

overcurrent protection for the installation, in accordance with the plug/equipment rating.

• Connect the PDU to an outlet that is in accordance with your local building codes and that is

adequately protected against excess currents, short circuits and earth faults.

• The electrical outlets supplying power to the equipment should be installed near the equipment

and easily accessible.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that

eliminate the connection to ground.

• Be sure to provide a local disconnect device on any models that are permanently installed

without a plug that is easily accessible.

• Never attempt to install electrical equipment during a thunderstorm.

• Individual equipment connected to the PDU should not draw more current than the individual

PDU’s outlet’s rating.

• The total load connected to the PDU must not exceed the maximum load rating for the PDU.

• Do not attempt to modify the PDU, input plugs or power cables.

• Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable

parts inside.

• Do not attempt to use the PDU if any part of it becomes damaged.

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to significantly

affect its safety or effectiveness is not recommended.

Important Safety Instructions

18-11-317-933059.indb 2 2/20/2019 4:26:36 PM

Installation

1-1 B

1-2

1-3

Note: The illustrations may differ somewhat from your PDU model.

1 Determine Installation Configuration. The PDUs covered by this owner’s manual support

these installation configurations: 2U, 1U and 0U rackmount; wall-mount and under-counter.

See below for installation configurations pertaining to your specific model. Choose a

configuration and follow the installation instructions in the appropriate section of Step 1

before proceeding to Step 2.

Note: Regardless of installation configuration, the user must determine the fitness of hardware and

procedures before mounting. The PDU and included hardware are designed for common rack and rack

enclosure types and may not be appropriate for all applications. Exact mounting configurations may vary.

1-1 2U Rack Installation. Attach the

included brackets to the side of the

PDU with the included screws A. After

installing the brackets, position the

PDU in the rack and install four user-

supplied screws through the unit’s

brackets and into the rack rails B.

1-2 1U Rack Installation. Attach the PDU

to the rack by inserting four user-

supplied screws A through the PDU

mounting brackets B and into the

mounting holes of the rack rail as

shown.

1-3 0U Rack Installation. Part 1: Remove

the screws C attaching the mounting

brackets to the PDU, change the

orientation of the brackets as shown

and reattach the brackets. Use only

the screws supplied by the

manufacturer or their exact equivalent

(#6-32, 1/4” flat head). Part 2: Attach

the PDU vertically by inserting two or

more user-supplied screws A through

the PDU mounting brackets B and

into mounting points in the rack or

rack enclosure.

18-11-317-933059.indb 3 2/20/2019 4:26:37 PM

Product specificaties

Merk:	Tripp Lite
Categorie:	Stekkerdoos
Model:	PDUMH30HV
Kleur van het product:	Zwart
Gewicht:	6210 g
Breedte:	444.5 mm
Diepte:	317.5 mm
Hoogte:	88.9 mm
Snoerlengte:	3.65 m
Gewicht verpakking:	7170 g
Breedte verpakking:	424.2 mm
Diepte verpakking:	502.9 mm
Hoogte verpakking:	198.1 mm
Materiaal behuizing:	Metaal
LED-indicatoren:	Ja
Land van herkomst:	Taiwan
Certificering:	UL 60950-1 (USA), CSA (Canada), Class A (Emissions), NOM (Mexico)
Duurzaamheidscertificaten:	RoHS
Temperatuur bij opslag:	-15 - 50 °C
Hoogte, in bedrijf:	0 - 3000 m
Afmetingen (B x D x H):	444 x 318 x 88 mm
Montage:	Horizontaal
Stekker:	NEMA L6-30P
(Buitenste) hoofdverpakking hoogte:	198.1 mm
(Buitenste) hoofdverpakking breedte:	424.2 mm
(Buitenste) hoofdverpakking brutogewicht:	7170 g
(Buitenste) hoofdverpakking lengte:	502.9 mm
Hoeveelheid per (buitenste) hoofdverpakking:	1 stuk(s)
Rackcapaciteit:	2U
AC-ingangsfrequentie:	50 - 60 Hz
Aantal AC uitgangen:	18 AC-uitgang(en)
Nominale input voltage:	208-240 V
Stopcontacttypes:	C13 coupler, C19 coupler
Stroom (max.):	30 A
PDU types:	Gemeten
Netspanning, in bedrijf:	208-240 V