System Sensor P2R-SP Handleiding

System Sensor Niet gecategoriseerd P2R-SP

Lees hieronder de 📖 handleiding in het Nederlandse voor System Sensor P2R-SP (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

1 I56-2769-020R

06-10

INSTALLATION AND MAINTENANCE INSTRUCTIONS

Selectable Output Strobes, Horns, and Horn/Strobes

3825 Ohio Avenue, St. Charles, Illinois 60174

800/736-7672, FAX: 630/377-6495

www.systemsensor.com

For use with the following models: P2R, P2RH, P2RK, P2RHK, P2W, P2WK, P2WH, P2WHK, P4R, P4RH, P4RK, P4W, P4WK, SR, SRH, SRK, SRHK, SW, SWK, SWH, SWHK, SW-CLR-

ALERT, PC2R, PC2RH,PC2RK, PC2RHK, PC2W, PC2WK, PC2WH, PC2WHK, PC4R, PC4RH, PC4W, PC4WK, PC4WHK, SCR, SCRH, SCRK, SCRHK, SCW, SCWK, SCWH, SCWHK, SCW-

CLR-ALERT, HR, HRK, HW, SR-P, SW-P, SRH-P, SWH-P,P2R-P, P2W-P, P2WH-P, P4R-P, P4W-P, SCW-P, PC2R-P, PC2W-P, PC2WH-P, SRK-P, SRHK-P, P2RK-P, P2RHK-P, SWK-P, SWHK-P,

P2WK-P, P2WHK-P, SR-SP, P2R-SP, PC2W-SP, SRK-R, SWK-R, SRHK-R, SWHK-R, P2RK-R, P2WK-R, P2RHK-R, P2WHK-R, SBHK, SBK-R

NOTE: All -R models are specifically designed for use with the WTP Series of Weatherproof plates

NOTE: When replacing outdoor units; device and back box must be replaced

NOTE: Models SBHK, SBK-R are UL listed for General Signaling

PRODUCT SPECIFICATIONS

Operating Temperature: Standard Products 32°F to 120°F (0°C to 49°C)

K Series –40°F to 151°F

Humidity Range: Standard Products 10 to 93% Non-condensing

K Series Meets NEMA 4X requirements

Strobe Flash Rate: 1 ﬂash per second

Nominal Voltage: Regulated 12VDC/FWR or regulated 24DC/FWR

Operating Voltage Range (includes ﬁre alarm panels with built in sync): 8 to 17.5V (12V nominal) or 16 to 33V (24V nominal)

Operating Voltage with MDL3 Sync Module: 8.5 to 17.5V (12V nominal) or 16.5 to 33V (24V nominal)

Input terminal wire gauge: 12 to 18 AWG

NOTE : Strobes will operate at 12 V nominal for 15 & 15/75 candela settings only. Switching between ranges is automatic.

DIMENSIONS FOR PRODUCTS AND ACCESSORIES

WALL PRODUCTS Length Width Depth CEILING PRODUCTS DIAMETER DEPTH

Strobe and Horn/Strobes (including lens)

5.6" 4.7" 2.5" Strobes and Horn/Strobes

(including lens)

6.8" 2.5"

142 mm 119 mm 64 mm 173 mm 64 mm

Horns

5.6" 4.7" 1.3"

SA-WBBC Red Weatherproof Back Box

7.1" 2.2"

142 mm 119 mm 33 mm

SA-WBBCW White Weatherproof Back Box

180 mm 51 mm

SA-WBB Red Weatherproof Back Box

5.7" 5.1" 2.0"

SBBCR Red Surface Mount Box

6.9" 5.3"

SA-WBBW White Weatherproof Back Box

145 mm 130 mm 51 mm

SBBCW White Surface Mount Box

175 mm 135 mm

SBBR Red Surface Mount Box

5.6" 4.7" 4.3" NOTE: SA-WBB, SA-WBBW, SA-WBBC and SA-WBBCW dimensions

do not include the two mounting tabs

SBBW White Surface Mount Box

142 mm 119 mm 109 mm

MOUNTING BOX OPTIONS

2-Wire Indoor Products 4-Wire Indoor Products K Series Products

4 × 4 × 1

1/2, Single Gang, Double Gang, 4˝ Octagon

SBBR/W (wall), SBBCR/W (ceiling) 4 × 4 × 11/ ,2 Double Gang, 4˝ Octagon SA-WBB/W (wall), SA-WBBC/CW (ceiling)

GENERAL DESCRIPTION

The SpectrAlert Advance series of notification appliances offers a wide range

of horns, strobes, and horn/strobes, for wall and ceiling applications, indoors

and outdoors. They are designed to be used on 12 or 24 volt, DC or FWR

(full wave rectified) systems. These products are electrically backward compat-

ible with the previous generation of SpectrAlert notification appliances. Horn/

strobe products are available in two versions. The 2-wire products fit systems

where a single NAC controls both horn and strobe. The 4-wire products are in-

tended for systems which have separate wiring circuits for the horn and strobe.

All SpectrAlert Advance products are suitable for use in synchronized systems.

The System Sensor MDL3 module may be used to provide synchronization.

K Series products are designed to be used over a wider range of temperatures

and are suitable for use in wet environments with outdoor backbox supplied

with product.

Wall and ceiling products may be used interchangeably (wall products

may be used on the ceiling and ceiling products may be used on the wall.)

FIRE ALARM SYSTEM CONSIDERATIONS

The National Fire Alarm Code, NFPA 72, requires that all horns, used for

building evacuation produce temporal coded signals. Signals other than those

used for evacuation purposes do not have to produce the temporal coded sig-

nal. System Sensor recommends spacing notification appliances in compli-

ance with NFPA 72.

LOOP DESIGN AND WIRING

The system designer must make sure that the total current drawn by the de-

vices on the loop does not exceed the current capability of the panel supply,

and that the last device on the circuit is operated within its rated voltage. The

current draw information for making these calculations can be found in the

tables within this manual. For convenience and accuracy, use the voltage drop

calculator on the System Sensor website (www.systemsensor.com).

When calculating the voltage available to the last device, it is necessary to

consider the voltage drop due to the resistance of the wire. The thicker the

wire, the smaller the voltage drop. Wire resistance tables can be obtained

from electrical handbooks. Note that if Class A wiring is installed, the wire

length may be up to twice as long as it would be for circuits that are not

fault tolerant.

NOTE: The total number of strobes on a single NAC must not exceed 40 for

24 volt applications or 12 for 12 volt applications. Loop resistance on a single

NAC should not exceed 120 ohms for 24 volt and 30 ohms for 12 volt systems.

I56-2769-020R

NOTICE: This manual shall be left with the owner/user of this equipment.

2 I56-2769-020R

06-10

CANDELA SELECTION

Adjust the slide switch on the rear of the product to the desired candela set-

ting in the small window on the front of the unit. All products meet the light

output profiles specified in the appropriate UL Standards. See Figures 1-3.

Use Table 1 to determine the current draw for each candela setting. For K

series products used outdoors at low temperatures, listed candela ratings must

be reduced in accordance with Table 2.

NOTE: SpectrAlert products set at 15 and 15/75 candela automatically work

on either 12V or 24V power supplies. The products are not listed for 12V op-

erating voltages when set to any other candela settings. For 4-Wire products,

total current draw may be determined by adding current draw for the specific

candela selection and the current draw for the specific horn selection use

Table 1 and Table 3.

TABLE 1. STROBE CURRENT DRAW ( A) FOR S, SC, P4 & PC4 SERIES: m

Candela 8–17.5 Volts 16–33 Volts

DC FWR DC FWR

Standard Candela Range

15 123 128 66 71

15/75 142 148 77 81

30 NA NA 94 96

75 NA NA 158 153

95 NA NA 176181

110 NA NA 195202

115 NA NA 210 205

High Candela Range

135 NA NA 228 207

150 220NA NA 246

177 NA NA 281 251

185 NA NA 286 258

TABLE 2. CANDELA DERATING:

Listed Candela Candela rating at –40°F

(K Series Outdoor Applications Only)

Do not use below 32°F15/75

75 44

95 70

110 110

115 115

135 135

150 150

177 177

185 185

HORN SELECTION

Turn the rotary switch on the back of the product to the desired setting. For

horn and 4-wire horn/strobe products, the current draw for each setting is

listed in Table 3. For 2-wire horn/strobe products (P2 series), current draws

are listed in Tables 4 and 5. The sound output measurement for each horn

setting is shown in Table 6.

TABLE 3. HORN CURRENT DRAW (mA) FOR H, P4 & PC4 SERIES:

Pos Sound Pattern dA Out 8–17.5 Volts 16–33 Volts

DC FWR DC FWR

1 Temporal High 57 55 69 75

2 Temporal Medium 44 49 58 69

3 Temporal 38 44 44 48Low

4 Non-temporal High 57 56 69 75

5 Non-temporal Medium 42 60 6950

6 Non-temporal 44Low 41 50 50

7 Coded High 57 55 69 75

8 Coded Medium 44 56 6951

9 Coded 40 46 52Low 50

NOTE: In positions 7, 8, and 9, temporal coding must be provided by the NAC.

If the NAC voltage is held constant, the horn output will remain constantly on.

Positions 7, 8, and 9 are not available on 2-wire horn/strobe products.

FIGURE 2. LIGHT OUTPUT -

HORIZONTAL DISPERSION

Figures 1-3 list the minimum light output requirements per UL1971.

FIGURE 3. LIGHT OUTPUT - VERTICAL DISPERSION, WALL TO FLOOR

Degrees* Percent of

Rating

0 100

5-25 90

30-45 75

50 55

55 45

60 40

65 35

70 35

75 30

80 30

85 25

90 25

Compound 45

to the right 24

Compound 45

to the right 24

Degrees* Percent of

Rating

0 100

5-30 90

35 65

40 46

45 34

50 27

55 22

60 18

65 16

70 15

75 13

80 12

85 12

90 12

Degrees* Percent of

Rating

0 100

5-25 90

30-45 75

50 55

60 45

65 35

70 35

75 30

80 30

85 25

90 25

*Tolerance of ±1 degree is permitted.

FIGURE 1. LIGHT OUTPUT - VERTICAL DISPERSION, CEILING TO WALLS

TO FLOOR

3 I56-2769-020R

06-10

TABLE 4. 2-WIRE HORN/STROBE CURRENT DRAW ( ) FOR P2 AND PC2 STANDARD CANDELA SERIES:

DC Input 8–17.5 Volts 16–33 Volts

15 cd 15/75 cd 15 cd 15/75 cd 30 cd 75 cd 95 cd 110 cd 115 cd

Temporal High 137 147 79 90 176 194107 212 218

Temporal Medium 132 144 69 80 97 157 182 201 210

Temporal Low 132 143 66 77 93 154 179 198 207

Non-temporal High 152 176 229141 91 100 116 201 221

Non-temporal Medium 133 145 75 85 163 187102 207 216

Non-temporal Low 144 68 79 96 156 182131 201 210

FWR Input

Temporal High 136 155 88 97 168 190112 210 218

Temporal Medium 129 152 78 88 160 184103 202 206

Temporal Low 129 76 86 160 184 194151 101 201

Non-temporal High 142 126 229161 103 112 181 203 221

Non-temporal Medium 134 155 85 95 166 189110 208 216

Non-temporal Low 132 154 80 90 184105 161 202 211

TABLE 5. 2-WIRE HORN/STROBE CURRENT DRAW ( ) FOR P2 AND PC2 HIGH CANDELA RANGE SERIES:

Sound Pattern 16–33 Volts Volts DC 16–33 Volts Volts FWR

135 cd 150 cd 177 cd 185 cd 135 cd 150 cd 177 cd 185 cd

Temporal High 245 259 290 297 258 265215 231

Temporal Medium 235 253 288 297 224 258209 250

Temporal Low 232 282 292 248 256251 207 221

Non-temporal High 255 233 248 275270 303 309 281

Non-temporal Medium 242 259 293 299 232 262 267219

Non-temporal Low 238 254 295 229 256 262291 214

TABLE 6. HORN OUTPUT ( BA) IN UL REVERBERANT ROOM:

Switch

Position Sound Pattern dA 8–17.5 Volts** 16–33 Volts** 24 V Nominal Measurements

Reverberant Anechoic

DC FWR DC FWR DC FWR DC FWR

1 Temporal High 78 78 84 84 88 88 99 98

2 Temporal Medium 75 75 80 80 86 85 96 96

3 Temporal 76 76 79 94 89Low 71 71 81

4 Non-temporal High 82 82 88 88 93 92 100 100

5 Non-temporal Medium 78 78 85 85 90 89 98 98

6 Non-temporal 73 74 86 84 96 92Low 81 81

7* Coded High 82 82 88 88 93 92 101 101

8* Coded Medium 78 78 85 85 90 89 97 98

9* Coded 74 75 85 83 96 92Low 81 81

*Horn & 4-wire Horn/Strobe only. ** Minimum dB rating for Operational Voltage Range as per UL 464.

FIGURE 4. WIRING 2-WIRE PRODUCTS:

–

INPUT

FROM

FACP

PRIOR

DEVICE

OUTPUT

DEVICE

OR EOL

A0367-01

FIGURE 5. WIRING 4-WIRE PRODUCTS:

–

INPUT

FROM

ACP OR

PRIOR

STROBE

INPUT

FROM

FACP OR PRIOR HORN

–

OUTPUT

TO NEXT

STROBE

OR EOL

OUTPUT NEXT TO

HORN OR EOL

A0366-00

FIGURE 6. SHORTING SPRING:

SHORTING SPRING

A0368-00

For 4-Wire installations, terminals 1, 2, and 3 connect to the strobe; terminals

4 and 5 connect to the horn. The horn and strobe circuits must be wired in-

dependently, and each circuit must be terminated with the appropriate EOL

device. Removal of a notification device will result in an open circuit indica-

tion on the strobe loop.

NOTE: A shorting spring is provided between terminals 2 and 3 of the mount-

ing plate to enable wiring checks after the system has been wired, but prior

to installation of the final product. This spring will automatically disengage

when the product is installed, to enable supervision of the final system. Only

available on indoor products(non K-series).

Product specificaties

Merk:	System Sensor
Categorie:	Niet gecategoriseerd
Model:	P2R-SP
Kleur van het product:	Rood
Soort:	Bedrade sirene
Gebruikershandleiding:	Ja
Materiaal behuizing:	Kunststof
Licht alarm:	Ja
Afmetingen (B x D x H):	119 x 64 x 142 mm
Operating voltage:	33 V
AC-ingangsspanning:	24 V
Bedrijfstemperatuur (T-T):	-40 - 66 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 93 procent
Plaatsing beschikbaar:	Binnen