Sonic Alert HA360SSBC Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Sonic Alert HA360SSBC (2 pagina's) in de categorie Beveiliging. Deze handleiding was nuttig voor 56 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
INSTALLATION AND SET UP FOR HOMEAWAREâ„¢ TRANSMITTER
HA360SSBC – Baby Cry
The HomeAwareâ„¢ HA360SSBC transmitter is
designed to alert you to the sound of a baby crying.
This transmitter alerts you through the HomeAwareâ„¢
Main unit and remote receivers located in other rooms.
Battery Backup Installation
Install a new 9 volt alkaline battery into the battery
compartment located on the back of the unit. See
diagram for battery door location. Battery backup will
provide power when a power outage has occurred.
Power will be provided for a continuous outage lasting
7 days, or for short outages up to two years.
Link Button Set Up
This procedure will link the HA360SSBC – Baby Cry to
your Main unit. The Main unit will also provide an alert
to all HomeAwareâ„¢ remote receivers. When using the
Bridge unit HA360BU all original Sonic Alert receivers
(SA101, SA201, BL300, and SB1000) will also alert
you.
It is best to do the link procedure in the same room with
the HomeAwareâ„¢ Main unit, make sure the unit is
plugged in.
To link a transmitter to your HomeAwareâ„¢ Main
unit:
1. Press set up button and the word LINK will be
shown on the display, press Enter. LINK will begin
blinking. (If LINK mode is entered by accident,
simply press the BACK button to exit and return to
the clock.)
2. Press and hold down the Link button on the back of
your transmitter for about 1 second. The red LED
on the transmitter will light up. Release the button.
3. Upon successful connection, the red LED on the
transmitter will flash 2 times, then turn off. The
HomeAwareâ„¢ main unit will briefly show DONE,
and return to the time display. Your transmitter is
now connected and ready to test and use.
Sensitivity Switch
You can adjust the sensitivity of the Baby Cry detector.
There are three levels to choose from: The HI setting is
the most sensitive setting and will alert you to more
sounds. Moving this switch to MED makes it less
sensitive and will alert you to less sound. The LO
setting is the least sensitive. If you are not picking up
the sound you need to be alerted to, simply move the
sensitivity switch to a higher setting. If you have set this
setting to HI and you are still not picking up the sound
try moving the transmitter closer to the sound.
When a sound is detected it will send a signal to the
HomeAwareâ„¢ base unit and all HomeAwareâ„¢ remote
receivers, also the red LED light will flash on the front
of the unit.
Low Voltage Input
HomeAwareâ„¢ transmitters have a low 120 volt AC
power supply that powers the HA360ss. Simply plug
the unit into any 120 volt AC power outlet. Next plug
the other end into the Low Voltage Input located on the
side, see diagram below.
FCC Requirements
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions; (1)
This device might not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
INSTALLATION AND SET UP FOR HOMEAWAREâ„¢ TRANSMITTER
HA360SSBC – Baby Cry
FCC Requirements (Continued)
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are
designed to provide responsible protect against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions manual, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will
not interfere in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment on and off, the user is encouraged to try to
correct the interference by one or more of the following
measures:
i. Reorient or relocate the receiving antenna.
ii. Increase the separation between the
equipment and receiver.
iii. Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
iv. Consult the dealer or and experienced radio
/TV technician for help
Modification not expressly approved by the
manufacturer could void the user’s authority to operate
the equipment under FCC rules.
GENERAL DATA
UL listed Power Adaptor: AC100-240V~, 50/60Hz
Power Consumption: Adaptor Output: DC12V, 250mA
The Lightening
flash and
arrowhead within
the triangle is a
warning sign
alerting you of
dangerous voltage
inside the product.
CAUTION:
TO REDUCE
THE RISK
OF ELECTRICAL
SHOCK, DO
NOT
REMOVE THE
COVER
(OR BACK)
FROM THE
PRODUCT. NO
USER
SERVICEABLE
PARTS
INSIDE. REFER
SERVICING TO
YOUR SONIC
ALERT DEALER.
The exclamation
mark within the
triangle is a
warning sign
alerting you of
important
instructions
accompanying
the product.
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
The normal function of the product may be
disturbed by Strong Electro Magnetic Interference.
If so, simply reset the product to resume normal
operation by following the instruction manual. In
case the function could not resume, please use the
product in other location.
– Attention should be drawn to the environmental
aspects of battery disposal.
– T This indicating separate collection for
electrical and electronic equipment.
SONIC ALERT’S 1 YEAR LIMITED WARRANTY
The HomeAwareâ„¢ HA360SSBC are warranted
against manufacturing defects in materials and
workmanship for one (1) year from the date of
purchase. Within this period Sonic Alert will repair or
replace at our option the HomeAwareâ„¢
HA360SSBC without charge for parts and labor.
Simply contact our customer service
department to obtain an RA (return
authorization number) and instructions on how
to process your product for return. Call 1-888-
864-2446 or e-mail to RMA@sonicalert.info.
You’ll need a copy of your receipt to process
the return authorization.
Sonic Alert Warranty Center
1081 West Innovation Dr. Kearney, MO 64060,
USA.
Made in China
Sonic Alert, Troy, MI 48083
www.SonicAlert.com 1-888-864-244


Product specificaties

Merk: Sonic Alert
Categorie: Beveiliging
Model: HA360SSBC

Heb je hulp nodig?

Als je hulp nodig hebt met Sonic Alert HA360SSBC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Beveiliging Sonic Alert

Handleiding Beveiliging

Nieuwste handleidingen voor Beveiliging