Sonic Alert DB100 Handleiding

Sonic Alert Beveiliging DB100

Lees hieronder de 📖 handleiding in het Nederlandse voor Sonic Alert DB100 (2 pagina's) in de categorie Beveiliging. Deze handleiding was nuttig voor 63 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

WIRELESS DOORBELL SIGNALER

MODEL DB100

SONIC ALERT’S 5 YEAR LIMITED WARRANTY

The Wireless Doorbell Signaler Model DB100 is

warranted against manufacturing defects in materials and

workmanship for five (5) years from the date of purchase.

Within this period Sonic Alert will replace at our option the

DB100 without charge for parts and labor. Simply send

the DB100 (postpaid) and a copy of your sales slip as

proof of purchase to:

Sonic Alert Inc., 1050 E. Maple Road, Troy MI 48083

Operation

The state-of-the-art Doorbell Signaler will alert you when

someone comes to visit. The DB100 is the only doorbell

signaler that does not require wires and can be installed in

seconds. DB100 signaler will alert you that someone is at your

door by flashing a light plugged into it and any other Sonic

Alert remote receivers you may have. The DB100 is designed

to work in homes with or without an existing doorbell or

chime. Selecting Flash Rate

Other features include a selectable number of flashes (5 or 10),

and different flash code for front door, rear door, or intercom.

Additional sensors (DB100T - sold separately) can be used for

2nd door. There is also a built-in chime for hearing members of

the family. The DB100 receives an RF (radio) signal from the

DB sensor, and flashes the light plugged into the built-in outlet

of the signaler. Use a 300-watt or less incandescent lamp only.

The signaler can send a signal to all Sonic Alert remote

receivers. Note: Must be used only with Sonic Alert

receivers for proper operation. Other manufacturers’

products are not reliable with our products.

DB100 Signaler DB Sensor

INSTALLATION

To install the DB100, follow the diagrams and instructions on the

following page that match the type of installation you need for

your home. If the installation follows diagram 1, a 12-volt

alkaline battery is required in the DB sensor.

Please check the switches on your DB Sensor before installing.

Do not change switches 1-6. These are pre set.

Setting the Dip Switches:

DB Sensor settings (smaller unit) for dip switches 1 thru 6 are set

at the factory and only need to be changed if your neighbor has a

DB100 or DB200. The 8 dip switches should be set as follows:

a) 1 thru 3 dip switches are set in the ON position and 4 thru 6

are set in the OFF position. If you need to change the dip switch

settings to avoid interference with your neighbors, make sure you

change the DB100 Signaler to match the DB Sensor.

b) The 7th switch is for when you are using 2 sensors; this switch

determines the settings for front or back door. If using for one

door only set this switch in the ON position. At this setting your

unit will flash at a fast rate and will make a ding/dong sound. If

using 2 sensors, one for the front door and one for the back door,

the setting for the 2nd sensor would be in the OFF position. In this

position the front door will flash at a different flash rate than the

back door. In the OFF position your back door sensor will flash

at a slow rate with a ding/dong sound.

c) The 8th switch determines the number of flashes when

someone is at your door. In the ON position your unit will flash 5

times and in the OFF position your unit will flash 10 times. This

feature is wonderful when you have an extra sensor for the back

door. One sensor would be set in the ON position and the other

would be set in the OFF position.

OFF

1 2 3 4 5 6 7 8

Setting the Audio Switch:

Top - OFF

Bottom - ON

Located on the DB100 Signaler (larger unit):

The speaker switch allows you to turn the Audio Alarm ON or

OFF. ON is down and OFF is up.

Multi-Function Input Jack:

Located on the right side of the DB Sensor, this input jack is

for installations as shown below in diagram 2 & 3.

DB100 INSTALLATION DIAGRAMS

Battery free installation (diagram 3):

Use wire provided, plug into jack outlet on side of

Transmitter. Remove chime cover and connect the red

and yellow wires to chime box terminal screws common

and front.

Troubleshooting & Help:

If you’ve followed the directions and are still having problems

please try the following suggestions:

1) Check battery in the sensor. Must be a 12-volt alkaline type.

2) Check dip switch settings. Both the sensor and the signaler

must match as shown in figure 1.1 above.

3) Check outlet for power.

4) Move the Signaler to an outlet closer to the sensor unit.

5) If using the Multi-Function input jack make sure that the wires

are not touching each other. See diagram number 2 & 3 for

proper installation.

6) Check that sensor is not further than 50 feet from the receiver.

7) Do not place sensor on steel doors or steel door frames.

For Technical help call 1-248-577-5400

M-F 8:00 a.m. – 5:00 p.m. Eastern Time

Or e-mail us with your questions at sonic-info@sonicalert.com

Warranty:

Thank you for purchasing this high quality Sonic Alert product. We hope you

will have many years of satisfied use. This Sonic Alert product comes with a

limited 5-year warranty so please retain your receipt in a safe place for possible

future reference; you will need in the event of warranty service.

Sonic Alert, Inc.

1050 East Maple Rd.

Troy, MI 48083

V/TTY 1-248-577-5400 fax 248-577-5433

E-mail: sonic-info@sonicalert.com

Web Site: www.SonicAlert.com

REV 1.5 (2008)

This device complies with Part 15 of the FCC Rules and with RSS-210

of Industry Canada. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including

interference that may cause undesired operation.

WARNING: Changes or modifications not expressively

approved by the party responsible for compliance could void

user’s authority to operate the equipment.

Product specificaties

Merk:	Sonic Alert
Categorie:	Beveiliging
Model:	DB100

Heb je hulp nodig?

Als je hulp nodig hebt met Sonic Alert DB100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Beveiliging Sonic Alert

Sonic Alert SB300 Handleiding

14 April 2023

Sonic Alert SS12V Handleiding

14 April 2023

Sonic Alert HA360MV Handleiding

14 April 2023

Sonic Alert SA201 Handleiding

14 April 2023

Sonic Alert DB100 Handleiding

14 April 2023

Sonic Alert HA360SSSC Handleiding

14 April 2023

Sonic Alert HA360MVSB Handleiding

14 April 2023

Sonic Alert RH 100 Handleiding

14 April 2023

Sonic Alert HA360SSBC Handleiding

14 April 2023

Sonic Alert HA360BR Handleiding

14 April 2023

Handleiding Beveiliging

Nieuwste handleidingen voor Beveiliging

Geemarc SOS-PRO 295 Handleiding

6 Maart 2024

Technaxx TX-106 Handleiding

4 Februari 2024

One2track Safety Angel Handleiding

16 Oktober 2023

Sygonix SY-3851632 Handleiding

16 Oktober 2023

Sygonix 1326052 Handleiding

16 Oktober 2023

Sygonix 43588A WLAN Camera Handleiding

16 Oktober 2023

Sygonix 43176S LAN Camera Handleiding

16 Oktober 2023

Sygonix SY-3181234 Handleiding

16 Oktober 2023

Sygonix Touch IP65 Handleiding

16 Oktober 2023

Sygonix 1882082 Handleiding

16 Oktober 2023