SkyRC e430 Handleiding

SkyRC Batterij-oplader e430

Lees hieronder de 📖 handleiding in het Nederlandse voor SkyRC e430 (4 pagina's) in de categorie Batterij-oplader. Deze handleiding was nuttig voor 158 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Thank you for your choice of the SKYRC e430, 100-240V AC balance charger. This unit is simple to use

but its operation does require some knowledge on the part of the user. Please read this entire operating

manual completely and attentively before using this product, as it covers a wide range of information on

operating and safety.

SKYRC e430 Charger is an economic, high quality 100-240V AC balance charger, designed for charging

LiPo and LiFe batteries from 2-4 cells in balance mode. The circuit power is 30W and max charge current

can reach to 3A. There are three kinds of charge current 1A/2A/3A that can be selected. You could select

the proper charge current according to battery capacity.

INSTRUCTION MANUAL

INTRODUCTION

CHARGE PROCEDURES

SKYRC e430 comes with the built in power supply. You can connect the AC power cord to the AC socket (100-240V AC)

directly.

Insert the AC power cord into the charger.

Insert the AC cord into a wall socket (100-240V). All LEDS will light for 1 second and the charge status LED will flash

green which indicates the charger is ready to charge.

Select the battery type LiPo/LiFe by the slide switch.

Select the proper charging current 1A/2A/3A by the slide switch.

Connect the battery main charge lead to battery socket which is in the front side of the charger and battery balance

wire to balance port which is in the right side of the charger.

The charger starts charging. The charge status LED and the cell status LED will glow constant red. If the battery

pack is 2-cell, Cell 1 and Cell 2 LEDs will glow constant red; if the battery pack is 3-cell, Cell 1, Cell 2 and Cell 3

LEDs will glow constant red; and so on.

During the charging progress, when the charge status LED glows constant red, the charger is charging in CC mode;

when the charge status LED glows constant orange, the charger is charging in CV mode;

When the cell LED is flashing, this cell is discharging

for balancing.

When the battery is fully charged, the charge status

LED will glow constant green.

Unplug the battery from the charger and the charge

status LED will flash green which indicates the

charger is ready to charge another battery.

Please refer to following steps to charge the battery,

- - - -1 2

SPECIFICATION

AC Input

Battery Type

Cell Count

Charge Current

Cell Terminate Voltage

Circuit Power

Current Drain for Balancing

Dimension

Weight

100-240V

LiPo/LiFe

2-4 cells

1A/2A/3A ± 10%

LiPo: 4.2V ± 0.02V / LiFe: 3.6V ± 0.02V

30W

200mA

69.4x110.7x40.5mm

193g

SK-100107

This diagram shows the correct way to connect

your battery.

Failure to connect as shown in this diagram will

damage this charger.

CAUTION:

10)

Battery Type Switch

Cell 2 LED Indicator

Cell 1 LED Indicator

Cell 4 LED Indicator

Cell 3 LED Indicator

Battery Socket

AC 100-240V

Power Jack

Charge Current Switch

Charge Status LED Indicator

Balance Socket

EXPLANATION OF LED STATUS

If there is an error, the charge status LED and one of the cell LED will blink in sequence.

* Error Message

LED green blinking

LED glows constant red

LED glows constant orange

LED glows constant green.

LED glows constant red.

LED flashes red

The charger is ready to charge.

The charger is charging in CC mode.

The charger is charging in CV mode.

The charging process finishes.

The cell is charging.

The cell is discharging.

Charge Status LED

Cell Status LED

In this case, please disconnect the power cord from the wall socket and unplug the battery from the charger.

Charge Status LED + Cell 1 LED

Charge Status LED + Cell 2 LED

Charge Status LED + Cell 3 LED

The voltage difference among cells is too big (more than 300mV)

Wrong connection

Low Voltage Protection(≤2.5V)

LED Status Error Message

CONNECTION DIAGRAM

LiPo

TO 100-240V AC

Socket

Cell LED will blink simultaneously

Charge Status Cell 1+2+3+4 LED

Cell 1+2 LED

The whole charging process exceeds 5 hours.

Battery type changed while charging.

7504-0851-02

Manufactured by

SKYRC TECHNOLOGY CO LTD  ., .

www skyrc com. .

- - - -3 4

THE SET CONTAINS

WARNING AND SAFETY NOTES 

WARRANTYAND SERVICE

We guarantee this product to be free of manufacturing and assembly defects for a period of one year from the time of

purchase. The warranty only applies to material or operational defects, which are present at the time of purchase. During

that period, we will repair or replace free of service charge for products deemed defective due to those causes.

You will be required to produce proof of purchase (invoice or receipt). This warranty is not valid for any damage or

subsequent damage arising as a result of misuse, modification or as a result of failure to observe the procedures

outlined in this manual.

LIABILITY EXCLUSION

This charger is designed and approved exclusively for use with the types of battery stated in these Instruction Manual.

SKYRC accepts no liability of any kind if the charger is used for any purpose other than that stated. We are unable to

ensure that you follow the instructions supplied with the charger, and we have no control over the methods you employ

for using, operating and maintaining the device. For this reason we are obliged to deny all liability for loss, damage or

costs which are incurred due to the incompetent or incorrect use and operation of our products, or which are connected

with such operation in any way. Unless otherwise prescribed by law, our obligation to pay compensation, regardless of

the legal argument employed, is limited to the invoice value of those SKYRC products which were immediately and

directly involved in the event in which the damage occurred.

SkyRC e430 Charger

AC Power Cord

18AWG Wire Charging Cable

CONFORMITY DECLARATION

SKYRC e430 satisfies all relevant and mandatory CE directives and FCC Part 15 Subpart B: 2014.

The product has been tested to meet the following technical standards:

This marking indicates that this product should not be disposed with other household wastes throughout

the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal,

recycle it responsibly to promote the sustainable reuse of material resources. To return your used device,

please use the return and collection systems or contact the retailer where the product was purchased.

They can take this product for environmental safe recycling.

Conform

CE-EMC

FCC-VOC 47 CFR Part 15

Test Standards Title Result

Radio frequency devices

Conform

EN60335-2-29

CE-LVD

Household and similar electrical appliances –. Safety –.

Part 2-29: Particular requirements for battery chargers.

Conform

This charger is not intended for use by persons (include children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do

not play with the appliance.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similar qualified persons

in order to avoid a hazard.

This charger is suitable for charging rechargeable LiPo/LiFe batteries. Do not attempt to recharge non-rechargeable

batteries. Charging other types of batteries may cause fire or explosion.

Never leave the charger unattended when it is connected to its power supply.

The allowable AC input voltage is 100-240V AC. Never connect it to any other voltage.

Protect charger from dust, dirt and damp.

Never place the charger and batteries connected to it on any form of flammable surface. Never operate the charger

in the vicinity of inflammable material or gas.

During charging, the battery must be placed in a well ventilated area . Never place the charger on a carpet or similar

surface.

Take great care to maintain correct battery polarity, and avoid shot-circuit. Read the battery manufacturer's

instructions and adhere to them strictly.

The charger must only be plugged into an earthed socket-outlet (for portable class 1 battery chargers for outdoor

use)

The connection to the supply mains is to be in accordance with the national wiring rules when battery chargers for

installation in caravans and similar vehicles.

Note:

The warranty service is valid in China only.

If you need warranty service overseas, please contact your dealer in the first instance, who is responsible for

processing guarantee claims overseas. Due to high shipping cost, complicated custom clearance procedures to

send back to China. Please understand SkyRC can't provide warranty service to overseas end user directly.

If you have any questions which are not mentioned in the manual, please feel free to send email to info@skyrc.cn

EN61000-3-3

Electromagnetic compatibility (EMC) - Part 3-3: Limitation

of voltage supply systems for equipment with rated

current 16 A.≤

EN61000-3-2

Electromagnetic compatibility (EMC) –

Part 3-2: – Limits for harmonic current emissions (equipment

input current up to and incelding 16 A per phase)

EN55014-1

Electromagnetic compatibility – Requirements for

household appliances, electric tools and similar     

apparatus – Part 1 Emission :

EN55014-2

Electromagnetic compatibility – Requirements for

household appliances, electric tools and similar     

apparatus – Part 2 Immunity Product Family Standard :

RECOMMENDED ACCESSORIES

Tamiya charging cable

5201-0030-01

Crocodile clip

charging cable

5201-0031-01

EC3 charging cable

5201-0034-01

Dean charging cable

520 -00 -013 16

JST/BEC charging cable

5201-0043-01

EN 60335-1: 2012

+A11: 2014

Household and similar electrical appliances - Safety - Part 1:

General requirements

EN 62233: 2008 Measurement methods for electromagnetic fields of household

appliances and similar apparatus with regard to human exposure

Conform

Product specificaties

Merk:	SkyRC
Categorie:	Batterij-oplader
Model:	e430
Kleur van het product:	Zwart
Gewicht:	193 g
Breedte:	69.4 mm
Diepte:	110.7 mm
Hoogte:	40.5 mm
Soort:	Batterijlader voor binnengebruik
LED-indicatoren:	Ja
Meegeleverde kabels:	AC
Ondersteund aantal accu's/batterijen:	4
Ingangsspanning:	100-240 V
Stroomspanning bescherming:	Reverse polarity, Short circuit
Frequentie:	- Hz
Spanning:	- V
Compatibele batterij technologiën:	Lithium-Polymeer (LiPo)
Laadstroom:	3 A