Sani-Lav 532F Handleiding
Lees hieronder de π handleiding in het Nederlandse voor Sani-Lav 532F (5 pagina's) in de categorie Spoelbak. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/5
1
W A L L M O U N T S C R U B S I N K
Operating Manual for Wall Mount Stainless Steel Scrub Sink
Models 532F 532F-0.5 and
of Domestic and Foreign Parts
Columbia does not recommend use with harsh chemicals.
Product Compliance
NSF/ANSI 2 Food Equipment, NSF/ANSI 61, Section 9, ASME A112.18.1/CSA B125.1
2
W A L L M O U N T S C R U B S I N K
C O L U M B I A S P E C I F I C AT I O N S
800.626.2117 columbiasinks.com info@columbiasinks.com
Β©2021 Columbia Products
Installation Instructions
Step 1
1. Establish sink location on the wall.
2. Measure a recommended 45β from finished floor and draw a level line which will be the top edge
of the wall mounting bracket.
3. Hold the wall mounting bracket against the wall and mark the wall where the holes are. Drill holes
and secure bracket to the wall as shown in illustration A. Screws are not provided.
Step 2
1. Install faucet to the sink using faucet mounting kit provided. We recommend using pipe thread
sealant instead of Teflon tape.
2. Install strainer assembly to the drain hole.
3. Connect hot and cold water supply lines (not included) to the back of faucets.
Step 3
1. Position sink onto the wall bracket.
2. Mount support bracket to the bottom of the sink. Do not tighten.
3. Slide or push support brackets against the wall and mark holes for fastening. See illustration B.
4. Remove support brackets from the sink and drill holes for fastening.
5. Install fastening hardware to the drilled holes. (not included)
6. Mount support bracket to the bottom of the sink and fasten them to the wall.
Step 4
1. Install valves onto the sink.
2. Install elbow fittings to Knee Pedal Valves.
3. Connect hot and cold connecting tubes from the spouts to valves.
Step 5
1. Connect waste line or drain pipe to the strainer assembly.
2. Connect hot and cold water supply line to the water source.
Step 6
1. Remove aerator from the spout assembly and flush water system. Check connections for leaks.
Replace aerator onto the spout assembly.
2. We recommend sealing top of backsplash to wall as shown in illustration C.
WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),
Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
NOTE: Lead content originates from Brass components in valves and faucets and is certiξed under
NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.
Notice for California Consumers
Parts List
(1) Wall mount sink
(1) 8β on center faucet
(1) Faucet mounting kit
(1) Wall-mounting bracket
(2) Support brackets
(4) Support bracket mounting bolts and washers
(1) Strainer assembly with basket
Tools Required
Tape measure
Adjustable wrench
Drill motor and drill bits
Pipe wrench
Level
Safety glasses
Screw drivers: phillips and standard
Pencil
Socket wrench
Trouble Shooting Guide
Problem Possible Cause To Diagnose Remedy
Water drips from
the spout or from
under the lever.
1. Seat washer is worn
2. Seat is worn
3. O-rings are worn
Shut cold water source off.
See if water still leaks from the
spout. If leaks continues repair
hot side if not repair cold side.
Recommend
installing hot
or cold faucet
repair kit.
Go to for more information on replacement parts and installation videos.columbiasinks.com
Illustration A
Illustration B
Illustration C
3
W A L L M O U N T S C R U B S I N K
C O L U M B I A S P E C I F I C AT I O N S
800.626.2117 columbiasinks.com info@columbiasinks.com
Β©2021 Columbia Products
7.5β (191mm)
24.75β(628.65mm)
.5β R
(12.7mm)
Hole Conο¬gurations
Front
1.5β (38mm)
19.5β (495.3mm)
2β (51mm) 45ΒΊ
35β (889mm)
suggested
ο¬oor to rim
height
Side
16.75β
(425.45 mm)
Wall-mounting bracket
4β (101.6mm)
4β (101.6mm)
16β
(406.4mm)
19.5β
(495.3mm)
Top 31β(787.4mm)
15.5β
(393.7mm)
10.25β
(260.35mm)
Cross-breaks
to aid drainage
3.5β drain hole
(88.9mm)
28β (711.2mm)
1.5β (38mm)1.5β
(38mm)
8β
(228.6mm)
10.5β
(266.7mm)
.437β (6mm)
.75β (19mm) slot
.437β (6mm)
dia. hole
.875β (22mm)
dia. holes (1)
2β
(51mm) .875β
(22.22mm)
Back
Splash
.375β
dia. hole
Wall Mounting Detail
12.25β
(311.15mm)
8β
(228.6mm)
10.5β
(266.7mm)
11.5β
(292.1mm) 11.5β
(292.1mm)
8β
(203.2mm)
Back Splash
Supply Line Detail
1/2β Male NPT
Hot
from Wall
Cold
from Wall
Product specificaties
| Merk: | Sani-Lav |
| Categorie: | Spoelbak |
| Model: | 532F |
Heb je hulp nodig?
Als je hulp nodig hebt met Sani-Lav 532F stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Spoelbak Sani-Lav
9 Juli 2023
9 Juli 2023
9 Juli 2023
9 Juli 2023
9 Juli 2023
9 Juli 2023
9 Juli 2023
8 Juli 2023
8 Juli 2023
8 Juli 2023
Handleiding Spoelbak
- Spoelbak Bartscher
- Spoelbak Blaupunkt
- Spoelbak Franke
- Spoelbak Hendi
- Spoelbak Hotpoint-Ariston
- Spoelbak Leisure
- Spoelbak Rangemaster
- Spoelbak Saro
- Spoelbak Smeg
- Spoelbak Teka
- Spoelbak Concept
- Spoelbak Blanco
- Spoelbak Caple
- Spoelbak CDA
- Spoelbak Kernau
- Spoelbak Artusi
- Spoelbak Foster
- Spoelbak Nodor
- Spoelbak Elkay
- Spoelbak Gustavsberg
- Spoelbak Schock
- Spoelbak Roca
- Spoelbak Advance Tabco
- Spoelbak Eagle Group
- Spoelbak Fulgor Milano
- Spoelbak Laveo
- Spoelbak Deante
- Spoelbak Tot Mate
- Spoelbak Atosa
- Spoelbak Kuchinox
- Spoelbak Oliveri
- Spoelbak Shaws
- Spoelbak Seima
Nieuwste handleidingen voor Spoelbak
17 December 2024
17 December 2024
16 December 2024
16 December 2024
6 December 2024
6 December 2024
6 December 2024
6 December 2024
6 December 2024
6 December 2024