Rolls MixMate 3 RM69 Handleiding

Rolls Staafmixer MixMate 3 RM69

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Rolls MixMate 3 RM69 (2 pagina's) in de categorie Staafmixer. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
RM69
MixMate 3
Mic/Source Mixer
USER GUIDE
ROLLS CORPORATION
SALT LAKE CITY, UTAH
09/11
www.rolls.com
SPECIFICATIONS
Input Impedance: Mic: 600 Ohms XLR balanced
Source:
22K Ohms RCA
Mic Insert: 22K Ohms 1/4” TRS insert
Max Input Level: Mic: -14 dBV Mic level
Source: 24 dBV
Headphone Output Impedance: >8 Ohms
Total - In/Out Connectors: 5: XLR, 5: Stereo RCA, 1: 1/4” TRS, 2: 3.5mm
Phantom Power: +15 VDC
Output Level: +17 dBV max
Output Impedance: 100 Ohms Balanced
Max Gain: Mic: 60 dB
Source: 26 dB
Tone Controls: +/-12 dB 100 Hz Bass
+/-12 dB 11kHz Treble
Noise Floor: - 80 dB, THD: <.025%,
S/N Ratio: 96 dB
Size: 19” x 1.75” x 4” (48.3 x 4.5 x 10 cm)
Weight: 5 lbs. (2.3 kg)
SCHEMATIC
USING THE MIC EFFECTS INSERT
In order to add eξ˜‚ ects to the microphone signal, an insert cable is needed. The Tip of the plug
acts as the Send, the Ring is the Return.
Connect the insert cable’s TRS end to the Mic FX
Insert jack on the rear of the RM69. Connect the
Tip connection to your eξ˜‚ ects processor’s Input
jack, and the Ring connection to the Output of
the eξ˜‚ ects processor. The RM69 eξ˜‚ ects insert
is mono, so if the eξ˜‚ ects processor is stereo -
choose a Mono output. You may need to refer
to your eξ˜‚ ects processor owners manual for more information about operating it in mono.
Make sure a microphone is properly connected to the RM69 and the unit is on. Speak into the
microphone and adjust the levels of your eξ˜‚ ects processor for the desired process and level of
eξ˜‚ ect.
IN
4
www.rolls.com
M
ONO
RM69
MIX MATE 3
HEADPHONE
LEVEL OUTPUT
1
ROLLS CORPORATION
5968 S 350 W
Murray, Utah 84107
1
RM69.SCH A
8 August 2011
Title
Size: Docum ent Number:
Date:
Rev:
Sheet of
MIXM ATE III RM69
Rb
+12V LEVEL
POWER
+12V
RIGHT IN
LEFT IN
FX INSERT
+12V
RIGHT IN
LEFT IN
+12V
RIGHT IN
LEFT IN
+12V
+12V LEVEL
Vb
PHAN PWR
PHAN PWR
SOURCE 3
LINE OUT
+12V
D1
1N4001
P1
P100K
R107
22K
R106
330
R108
22K
R109
4.7K
R207
22K
P2
P100K
R208
22K
R209
4.7K
1 3
2
P5A
P100K X2
4 6
5
P5B
P100K X2
1 3
2
P6A
P100K X2
4 6
5
P6B
P100K X2
1 3
2
P8A
P100K X2
4 6
5
P8B
P100K X2
R603
22K
R606
22K
J7
PHONE 1/4
R117
100
1 3
2
P4A
P100K X2
4 6
5
P4B
P100K X2
R704
10K
R701
10K
R817
100
1 2
3
J1
XLR F PC
1 2
3
J2
XLR F PC
C25
503
C12
503
C13
503
C14
503
C15
503
R101
3.3K
R201
3.3K
R401
10K
R404
10K
R501
10K
R504
10K
R601
10K
R604
10K
C105
27PF
C205
27PF
C701
27PF
C26
27PF
R15
4.7K
R506
22K
R503
22K
R703
22K
R706
22K
6
5
7
8
U1B
4560
2
3
1
4
U1A
4560
2
3
1
4
U2A
4560
6
5
7
8
U2B
4560
2
3
1
4
U8A
4560
6
5
7
8
U8B
4560
2
3
1
4
U9A
4560
6
5
7
8
U9B
4560
6
5
7
8
U5B
4560
2
3
1
4
U5A
4560
6
5
7
8
U4B
4560
2
3
1
4
U4A
4560
C601
27PF
C602
27PF
2
3
1
4
U7A
4560
C501
27PF
C502
27PF
C402
27PF
C401 27PF
C104 27PF
C101
10U
C201 10U
R113
100K
D5
LDSG
R406
22K
R403
22K
R105
330
C103
.001
R102
3.3K
C102
10U
R205
330
C203
.001
R206
330
C202
10U
R202
3.3K
R807
100
R808 47K
2
3
1
4
U10A
4560
R818
47K
6
5
7
8
U10B
4560
C8
1000UF
BASS
TREBLE
RIGHT
BASS
TREBLE
LEFT
+12V
13
2
P10A
P100K X2
46
5
P10B
P100K X2
13
2
P11A
P100K X2
46
5
P11B
P100K X2
6
5
7
8
U11B
4560
2
3
1
4
U11A
4560
R809
33K
R810
22K
R811
33K
R813
33K
R814
1M
R815
10K
R816
10K
R6
22K
R1
22K
R3
51
R5
51
R819
33K
R820
22K
R821
33K
R824 1M
R823
33K
R825
10K
R826
10K
R9
51
R10
51
C3
10U
C6
10U
C806
220PF
C808
220PF
C807 .047
C805 .047
R812
33K
R822 33K
+Vph
+Vph
2
3
1
4
U12A
4560
6
5
7
8
U12B
4560
R2
22K
R7
22K
C1
27PF
C4
27PF
1
2
3
J8
PCRCAX2
R8
1K
R4
1K
R111
4.7K
R112
100K
R211
4.7K
R212
100K
R110
4.7K
R210
4.7K
P7
P100K
P12
P100K
C106
.1
C206
.1
C107
.01
C207
.01
6
5
7
8
U7B
4560
C204
27PF
+12V
+12V +12V
+12V
AUX OUT/
HDPHN
46
5
P3B
P100K X2
J9
PHONE 1/4
2
3
1
4
U3A
4556
6
5
7
8
U3B
4556
13
2
P3A
P100K X2
C16
47U
R12
10
R14
10
C17
47U
R13
10K
R11
10K
SOURCE 1
SOURCE 2
SOURCE 4
1
2
3
SW2A
DPDT
2
3
1
J11
JAPDC
R405
470K
R502
470K
R505
470K
R605
470K
R602
470K
R705
470K
R702
470K
R402
470K
1 2
3
J3
XLR F PC
PHAN PWR
1
3
J6A
RCAX4
2
J6B
RCAX4
4
6
J6C
RCAX4
5
J6D
RCAX4
4
6
J5C
RCAX4
5
J5D
RCAX4
2
J5B
RCAX4
1
3
J5A
RCAX4
C2
27PF
+12V
+12V
C20
27PF
C21
25PF C22
25PF
C2327PF
C108
10U
C109
10U
C208
10U
C209
10U
C403
1U
C404
1U
C503
1U
C504
1U
C18
1U
C19
1U
C24
1U
C702
1U
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
Vb
C27
10U
C28
10U
+Vph
C5
47U
R17
22K
R16
22K
Q3
2N3904
C7
47UR18
47K
J12
PHONE 1/8 Stereo
+12V +12V
SW3B SW SPST
SW3A SW SPST
1 2
3
J4
XLR JACK M
1 2
3
J10
XLR JACK M
Thank your for your purchase of the Rolls RM69 MixMate 3 Mic / Source Mixer. The RM69 mixes
two microphones with up to four stereo source signals such as CD players, karaoke machines,
MP3 Players, etc.. The unit is housed in a compact yet sturdy steel 1U rack chassis.
INSPECTION
1. Unpack and inspect the RM69 box and package.
Your RM69 was carefully packed at the factory in a protective carton. Nonetheless, be sure to ex-
amine the unit and the carton for any signs of damage that may have occurred during shipping.
If obvious physical damage is noticed, contact the carrier immediately to make a damage claim.
We suggest saving the shipping carton and packing materials for safely transporting the unit in
the future.
2. For warranty information, visit our website; www.rolls.com Please register your new RM69
there, or complete the Warranty Registration Card and return it to the factory.
DESCRIPTION
FRONT PANEL
IN
4 MONO
RM69
MIX MATE 3
www.rolls.com
HEADPHONE
LEVEL OUTPUT
INPUT: Balanced XLR jack for connection to a dynamic or condenser microphone. This jack paral-
lels the Channel 1 Microphone Input on the rear panel.
NOTE: The following two descriptions are for Mic 1 and Mic 2.
LEVEL: Adjusts the amount of signal from the Microphone Input channel to the Main Outputs.
TONE: Adjusts the relative frequency components of the Mic signal. Turning this control clock-
wise from the center (detented) position decreases the low frequencies. Turning the control
counter-clockwise from center decreases the high frequencies.
SOURCE LEVEL CONTROLS 1 - 4: Adjust the amount of signal from the indicated Source channel
to the Main Outputs.
IN 4: 1/8” (3.5 mm) Source Input jack. This jack parallels the Source 4 Input on the rear panel.
BASS: Varies the amount of the low frequency portion (150 Hz) of the Source signals.
TREBLE: Varies the amount of the high frequency portion (10 kHz) of the Source signals.
HEADPHONE LEVEL: Adjusts the amount of signal to the Headphone Output.
HEADPHONE OUTPUT: 1/8” Tip-Ring-Sleeve jack for connection to any standard pair of audio
headphones.
pwr LED:Indicates that the RM69 is powered on.
REAR PANEL
MixMate 3
MODEL RM6 9
MADE IN USA
+
-
ROLLS
VDC
PHANTOM POWER
OFF= DOW
O =UP
www.rolls.com
MAI OUTPUTS
DC INPUT: Connects to the included Rolls PS27s power adapter.
LINE OUTPUTS RCA: Unbalanced output jacks
XLR: balanced ouput jacks
SOURCE INPUTS: Unbalanced RCA input jacks.
FX INSERT: 1/4” Tip-Ring-Sleeve jack for connection to an insert plug (see diagram) and to an
eξ˜‚ ects processor. Allows for eξ˜‚ ects to be added to the microphone signals.
PHANTOM POWER: Dip switches for applying phantom power to the indicated microphone.
MICROPHONE INPUTS 1 and 2: Balanced XLR jacks for connecting to dynamic or condenser
microphones.
CONNECTION
Ensure the RM69 is securely mounted in a 19” rack. Connect the power supply to an AC outlet
(preferrably a power strip with master switch). If the unit is to be used in a permanent install,
connect all sources and microphones to the desired channels on the rear panel. Remember
which signal sources are connected to which Source Inputs.
For use in mobile DJ/Karaoke rigs, the microphone should be connected to the front panel Mi-
crophone Input so it may be easily removed when the mobile rig is packed.
OPERATION
Make sure all audio connections are in place, and power is applied to all pieces of equipment
necessary for operation, ie; speakers, power ampliξ˜ƒ ers, microphones etc.
Normally, only one source signal is heard at a time along with a microphone signal. Therefore,
begin with all Levels completely counter-clockwise (oξ˜‚ ). Keep the Headphone Level control
low at ξ˜ƒ rst. There will be nothing heard from the Main Outputs until you increase the level of a
Source or Mic channel. You may now turn up the Source’s for playing. Set the Headphone Level
for a comfortable amount. Increase the Source Level of the desired channel, and begin playing
the selection.

Product specificaties

Merk: Rolls
Categorie: Staafmixer
Model: MixMate 3 RM69

Heb je hulp nodig?

Als je hulp nodig hebt met Rolls MixMate 3 RM69 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Staafmixer Rolls

Rolls

Rolls MX410 Handleiding

29 Augustus 2024
Rolls

Rolls MixMate 3 RM69 Handleiding

16 Mei 2024
Rolls

Rolls MA255 Handleiding

16 Mei 2024
Rolls

Rolls RM167 Handleiding

16 Mei 2024
Rolls

Rolls RM89 Handleiding

17 April 2024
Rolls

Rolls Four Zone Mixer RM64 Handleiding

15 November 2023

Handleiding Staafmixer

Nieuwste handleidingen voor Staafmixer

Oster

Oster FPSTSM3711 Handleiding

20 December 2024
Oster

Oster FPSTHS3610 Handleiding

20 December 2024
Oster

Oster FPSTHB2615W Handleiding

20 December 2024
Girmi

Girmi MX03 Handleiding

17 December 2024
Girmi

Girmi MX17 Handleiding

17 December 2024
Girmi

Girmi MX39 Handleiding

17 December 2024
Behringer

Behringer XENYX 1003B Handleiding

14 December 2024
Taurus

Taurus Robot 750 Pink Edition Handleiding

11 December 2024
Ambiano

Ambiano GT-SB-08 Handleiding

10 December 2024
Pyrex

Pyrex SB-1110 Handleiding

9 December 2024