Projecta PC2100 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Projecta PC2100 (16 pagina's) in de categorie Batterij-oplader. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16
PRO-CHARGE
6 STAGE SWITCHMODE
BATTERY CHARGER
P/No.s PC400, PC800, PC1600, PC2100
2
IMPORTANT SAFETY INFORMATION
Please read this manual thoroughly before use and store in a safe place for future reference.
WARNING
• Explosive gases may escape from the battery during charging. Prevent flames and
sparks. Provide adequate ventilation.
• Before charging, read the instructions.
• For indoor use. Do not expose to rain.
• For charging 12 Volt lead acid batteries ONLY.
• Disconnect the 240V mains supply before making or breaking the connections to the
battery.
• The battery charger must be plugged into an earthed socket-outlet.
• Connection to supply mains is to be in accordance with National wiring rules.
• Do not attempt to charge non-rechargeable batteries.
• Never charge a frozen battery.
• If the AC cord is damaged do not attempt to use. It must be replaced or repaired by a
qualified person.
• Corrosive substances may escape from the battery during charging and damage delicate
surfaces. Store and charge in a suitable area.
• Ensure all vehicle accessories including lights, heaters, appliances etc are turned off
prior to charging.
• This appliance is not intended for use by young children or infirm persons unless they
have been adequately supervised by a responsible person to ensure that they can use
the appliance safely.
• Young children should be supervised to ensure that they do not play with the appliance.
3
6-STAGE AUTOMATIC CHARGING
This is a fully automatic battery charger with 6 charge stages.
Automatic charging protects your battery from being overcharged so you can leave the
charger connected to the battery indefinitely.
6-stage charging is a sophisticated charging technique that gives your battery longer life
and better performance compared to using traditional chargers.
Projecta’s Pro-Charge chargers are suitable for most 12V automotive, marine and deep
cycle batteries. They may also help restore drained and sulphated batteries.
The 6 charge stages are:
Rejuvenation; Soft Start; Bulk; Absorption; Battery Test and Float.
REJUVENATION
The rejuvenation stage is manually initiated and delivers a 24 hour high frequency,
intermittent charge that breaks down sulphation from the battery’s plates. Upon
completion, the charger will proceed to Soft Start.
SOFT START
This is a preliminary charge process that gently introduces power to the battery,
protecting the battery and increasing battery life.
BULK (CONSTANT CURRENT)
The Bulk stage reduces charging time by charging the battery at the maximum rate
(constant current) to a set voltage, at which point the battery is approximately 80%
charged.
ABSORPTION (CONSTANT VOLTAGE)
The absorption stage charges the battery to 100% by adjusting the charge rate allowing
the battery to absorb more power.
EQUALISATION (CALCIUM MODE ONLY)
Designed especially for calcium batteries, this stage returns calcium batteries to full
service by removing acid stratification of the electrolyte.
BATTERY TEST
The analysis mode tests the battery to ensure that it has taken the charge; if the
battery passes the test the charger will proceed to the float stage.
FLOAT
The Float stage maintains the battery at 100% charge without overcharging or
damaging the battery. This means the charger can be left connected to the battery
indefinitely.


Product specificaties

Merk: Projecta
Categorie: Batterij-oplader
Model: PC2100

Heb je hulp nodig?

Als je hulp nodig hebt met Projecta PC2100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Batterij-oplader Projecta

Handleiding Batterij-oplader

Nieuwste handleidingen voor Batterij-oplader