Projecta HDBC35 Handleiding

Projecta Batterij-oplader HDBC35

Lees hieronder de 📖 handleiding in het Nederlandse voor Projecta HDBC35 (16 pagina's) in de categorie Batterij-oplader. Deze handleiding was nuttig voor 83 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/16
6/12/24 VOLT AUTOMATIC/MANUAL
WORKSHOP
BATTERY CHARGER
P/No.s HDBC20, HDBC35
WARNING
• Explosive gases. Prevent flames and sparks. Provide adequate ventilation during charging.
• Before charging, read the instructions.
• For indoor use. Do not expose to rain.
• For charging lead acid batteries ONLY (of the size & voltage specified in the specifications table).
• Always charge the battery on the correct voltage setting. Never set the charger to a higher voltage
than the battery.
• Disconnect the 240V mains supply before making or breaking the connections to the battery.
• Do not attempt to charge non-rechargeable batteries.
• Never charge a frozen battery.
• This appliance is not intended for use by young children or infirm persons unless they have been
adequately supervised by a responsible person to ensure that they can use the appliance safely.
• Young children should be supervised to ensure that they do not play with the appliance.
• Charge the battery in a suitable area, as the battery may give off corrosive fumes which could
damage delicate surfaces.
• Ensure all vehicle accessories and lights are turned off prior to charging.
• If the AC cord is damaged, it must be returned to an authorized Service Center.
2
3
FEATURES
Automatic Charging
When in automatic mode the charger will stop charging the battery when the battery is fully charged.
You can leave the charger connected to the battery without risk of overcharging. Once the battery is full,
the battery charger will automatically start to maintain the battery. The charger monitors the battery voltage
and continues to top up the battery, keeping it fully charged and ready for use.
Manual Charging
The charger in this mode will continue to charge the battery until the timer finishes or is turned off and
requires the user to monitor the charging battery. When used by experienced users it can deliver an
equalization charge to balance the voltage in the battery’s cells.
LED Indication
OVERLOAD (Red LED Flashing): The LED will flash when the transformer or the current regulators (SCR’s)
have got too hot
POWER ON (Red LED ON): The LED comes on when connected to power and the charger is switched on
POWER ON (Red LED Flashing): Indicates that the battery clamps have been connected in reverse polarity
Charging (Orange LED on): The LED comes on indicating charging
Fully charged (Green LED on): The LED comes on when the battery is charged
VOLT (Red LED ON): The LED indicates that Voltage is being displayed
AMP (Red LED ON): The LED indicates that Amps or current is being displayed
LED Voltage/Amp Display
The charger has a VOLT and AMP meter built in. When the charger is initially powered up the display will
show voltage. When the VOLT / AMP button is pressed the Amps will be displayed, press the button again
the display will go back to Volts. When Volts is displayed this indicates the state of charge of the battery,
when Amps is displayed this indicates how much charge is being accepted by the battery.
Override Button
The battery charger measures the battery voltage at the clamps to determine if the battery is correctly
connected. A reading above 3V will activate the battery charger. In some instances where the battery is
extremely flat, it is possible to have correct connection and the battery to be below the 3V limit. In this
instance check the battery leads to ensure they are connected correctly and press the OVERRIDE button
to activate the battery charger.
Multi Voltage
Suitable for charging 6V, 12V & 24V batteries.

Product specificaties

Merk: Projecta
Categorie: Batterij-oplader
Model: HDBC35

Heb je hulp nodig?

Als je hulp nodig hebt met Projecta HDBC35 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Batterij-oplader Projecta

Projecta

Projecta HDBC35 Handleiding

9 Mei 2023
Projecta

Projecta IC5000 Handleiding

8 Mei 2023
Projecta

Projecta HDBC20 Handleiding

7 Mei 2023
Projecta

Projecta IC2500 Handleiding

24 April 2023
Projecta

Projecta IC1500L Handleiding

18 April 2023
Projecta

Projecta IC1500 Handleiding

8 April 2023
Projecta

Projecta BM320 Handleiding

7 April 2023
Projecta

Projecta AC250B Handleiding

2 April 2023
Projecta

Projecta BLT100 Handleiding

28 Maart 2023
Projecta

Projecta IDC45 Handleiding

26 Maart 2023

Handleiding Batterij-oplader

Nieuwste handleidingen voor Batterij-oplader

Yamaha

Yamaha CC-T1A Handleiding

2 December 2024
EMOS

EMOS N9361 Handleiding

2 December 2024
EMOS

EMOS N9341 Handleiding

2 December 2024
Vimar

Vimar ELVOX ZBA6 Handleiding

1 December 2024
Vimar

Vimar ELVOX ECB5 Handleiding

1 December 2024
Vimar

Vimar ELVOX ECB4 Handleiding

1 December 2024
Vimar

Vimar ELVOX ECB3 Handleiding

1 December 2024
StarTech.com

StarTech.com 160W-POWER-ADAPTER Handleiding

30 November 2024
Nitecore

Nitecore NES1200 Handleiding

30 November 2024
Nitecore

Nitecore D2 Handleiding

30 November 2024