Projecta BLT100 Handleiding

Projecta Batterij-oplader BLT100

Lees hieronder de 📖 handleiding in het Nederlandse voor Projecta BLT100 (4 pagina's) in de categorie Batterij-oplader. Deze handleiding was nuttig voor 59 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
6 & 12V BATTERY
100 AMPS
LOAD TESTER
P/No. BLT100
CAUTION- BATTERIES PRODUCE EXPLOSIVE GASES,
TO REDUCE THE RISK OF EXPLOSION OR INJURY
ALWAYS ENSURE:
• No sparks or ames are present
• Eye protection is worn
• All vehicle or battery manufacturers instructions are followed
• Beware of moving parts
NOTE
The LOAD switch must not be pressed for longer than 10 seconds at a time, or
the product may be damaged.
When operating the unit for the rst time it is normal for a small amount of smoke
to develop as the lubricants used in the manufacturing process burn off.
Specications
Battery Load Test: 6 & 12V Lead Acid Batteries
Load: 100Amp @ 12V
50Amp @ 6V
Maximum Load ‘ON’ Time: 10 Seconds
Recommended Cool Down Time: 2 Minutes
Capacity Range: 200-1000CCA
Voltage Measured: 0-16V
Operating Instructions
Battery Load Test
1. Connect the RED clamp to the Positive (+) battery terminal or post.
2. Connect the BLACK clamp to the Negative (-) battery terminal or post.
If testing a battery in the vehicle, ensure the engine and all loads are’OFF’.
3. Note the batteries open circuit Voltage (OCV).
4. Press the ‘LOAD’ switch for 10 Seconds. Before releasing the ‘LOAD’
switch read the meter to determine the battery’s condition or approximate
capacity (For 12V batteries 200-1000CCA) & note the battery’s Voltage
while under load (Load Volts).
Charging System Test (12 Volt Vehicles)
1. Connect the RED clamp to the Positive (+) battery terminal or post.
2. Connect the BLACK clamp to the Negative (-) battery terminal or post.
Ensure the load tester and cables are clear of any moving parts.
3. Start the vehicle’s engine and operate at a fast idle speed, keep all accessorises,
lights & heater fan ‘OFF’.
4. Note the battery voltage, which should be in the green section of the charging
test, between 13.6 - 15 Volts, this indicates that the alternator’s regulator is
functioning correctly.
5. Turn ‘ON’ the vehicle’s head lights, heater fan or any other accessories,
the battery voltage should remain higher than 13.6 Volts, indicating that
the alternator is generating sufcient current.

Product specificaties

Merk: Projecta
Categorie: Batterij-oplader
Model: BLT100

Heb je hulp nodig?

Als je hulp nodig hebt met Projecta BLT100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Batterij-oplader Projecta

Projecta

Projecta HDBC35 Handleiding

9 Mei 2023
Projecta

Projecta IC5000 Handleiding

8 Mei 2023
Projecta

Projecta HDBC20 Handleiding

7 Mei 2023
Projecta

Projecta IC2500 Handleiding

24 April 2023
Projecta

Projecta IC1500L Handleiding

18 April 2023
Projecta

Projecta IC1500 Handleiding

8 April 2023
Projecta

Projecta BM320 Handleiding

7 April 2023
Projecta

Projecta AC250B Handleiding

2 April 2023
Projecta

Projecta BLT100 Handleiding

28 Maart 2023
Projecta

Projecta IDC45 Handleiding

26 Maart 2023

Handleiding Batterij-oplader

Nieuwste handleidingen voor Batterij-oplader

Yamaha

Yamaha CC-T1A Handleiding

2 December 2024
EMOS

EMOS N9361 Handleiding

2 December 2024
EMOS

EMOS N9341 Handleiding

2 December 2024
Vimar

Vimar ELVOX ZBA6 Handleiding

1 December 2024
Vimar

Vimar ELVOX ECB5 Handleiding

1 December 2024
Vimar

Vimar ELVOX ECB4 Handleiding

1 December 2024
Vimar

Vimar ELVOX ECB3 Handleiding

1 December 2024
StarTech.com

StarTech.com 160W-POWER-ADAPTER Handleiding

30 November 2024
Nitecore

Nitecore NES1200 Handleiding

30 November 2024
Nitecore

Nitecore D2 Handleiding

30 November 2024