Projecta IDC25L Handleiding

Projecta Batterij-oplader IDC25L

Lees hieronder de 📖 handleiding in het Nederlandse voor Projecta IDC25L (16 pagina's) in de categorie Batterij-oplader. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/16
25 Amp, 5 Stage Switchmode
INTELLI-CHARGE
DC/SOLAR BATTERY CHARGER
P/No. IDC25L
2
WARNINGS
• Explosive gases may escape from the battery during charging.
Prevent flames and sparks and provide adequate ventilation
• Before charging, read the instructions
• FOR CHARGING 12 VOLT LITHIUM IRON PHOSPHATE BATTERIES ONLY
• Do not attempt to charge non-rechargeable batteries
• Never charge a frozen battery or when ambient temperature is below 0°C
• Corrosive and/or toxic substances may escape from the battery during charging and
damage delicate surfaces. Store and charge in a suitable area
• This appliance is not intended for use by young children or infirm persons unless they
have been adequately supervised by a responsible person to ensure that they can use
the appliance safely
• Young children should be supervised to ensure that they do not play with the
appliance
• Fit fuses as close to the batteries as possible to protect the cable in case of
short circuit
FEATURES
The IDC25L DC-DC charger is purposely designed for charging auxiliary batteries.
It includes all the features needed to maintain the auxiliary battery to its optimum
condition and to prolong the battery life.
SWITCHMODE TECHNOLOGY
The IDC25L converts your vehicle’s 12VDC/24VDC alternator power to the voltage
level allowing your batteries to be fully charged, prolonging battery life and
reliability. With the latest synchronous switching technology, efficiency of IDC25L
exceeds 94% at typical full load condition.
DUAL INPUT OPERATION
Allows two energy sources to power the IDC25L simultaneously. Solar input takes
precedence if solar and alternator inputs are present. When solar input cannot provide
enough energy to the load, the IDC25L will draw power from solar and alternator
simultaneously.
SOLAR MPPT
The IDC25L utilises sophisticated MPPT (Maximum Power Point Tracking) solar
regulator technology. MPPT maximises the power generated from the solar panels
to the auxiliary battery.
3
POWER SUPPLY (CONSTANT VOLTAGE OF 13.8 VOLTS)
This sets the charge in power supply mode giving a constant voltage of 13.8VDC.
This mode is best used where appliances are drawing power from the battery,
for example a fridge.
Power supply mode can also be used to reactivate a lithium iron phosphate battery
which is on internal low voltage disconnect mode. Currently, most high capacity
12V lithium iron phosphate batteries have an in-built battery management system
(BMS). When you discharge a 12V lithium iron phosphate battery to very low output
voltage, it will activate the battery’s internal low voltage disconnect protection –
the battery will be disconnected from the charger and load. However, in charge
mode, the IDC25L will only start charging if it detects the battery is connected.
To overcome this, set the IDC25L to power supply mode until the battery internal
low voltage disconnect protection is deactivated.
SUPERIOR 5 STAGE CHARGING
Using high speed microcontroller and proprietary charging algorithm, the IDC25L
delivers a sophisticated 5 stage charging process resulting in a faster and more
powerful charge, ideal for deep cycle batteries. The first two stages increase battery
life by gently starting to charge the battery at 5% and 25% of the bulk charge
respectively. The third stage, bulk (constant current), charges the battery much faster
while the fourth stage, absorption (constant voltage), ensures the battery is thoroughly
charged. The final stage, float, maintains the battery at a safe voltage allowing it to
be maintained and ready for use indefinitely.
IGNITION CONNECTION
The ignition connection activates the lower input voltage operation to suit vehicles
with smart (variable voltage) alternators.
TEMPERATURE COMPENSATION
The IDC25L is supplied with a 2 metre temperature sensor. The sensor monitors
the battery temperature and adjusts (compensates) the charger’s output to
prevent overcharging. This is ideal for batteries used in warmer/cooler climates or
environments.
REMOTE CHARGER STATUS INDICATION
A pink wire is provided for driving an external panel mount LED indicator (Eg Narva
P/No. 62090BL) to show the status of the charger. It shows whether the auxiliary
battery is on charge (Solid Colour) or the charger is in a fault condition (Flashing).

Product specificaties

Merk: Projecta
Categorie: Batterij-oplader
Model: IDC25L

Heb je hulp nodig?

Als je hulp nodig hebt met Projecta IDC25L stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Batterij-oplader Projecta

Projecta

Projecta HDBC35 Handleiding

9 Mei 2023
Projecta

Projecta IC5000 Handleiding

8 Mei 2023
Projecta

Projecta HDBC20 Handleiding

7 Mei 2023
Projecta

Projecta IC2500 Handleiding

24 April 2023
Projecta

Projecta IC1500L Handleiding

18 April 2023
Projecta

Projecta IC1500 Handleiding

8 April 2023
Projecta

Projecta BM320 Handleiding

7 April 2023
Projecta

Projecta AC250B Handleiding

2 April 2023
Projecta

Projecta BLT100 Handleiding

28 Maart 2023
Projecta

Projecta IDC45 Handleiding

26 Maart 2023

Handleiding Batterij-oplader

Nieuwste handleidingen voor Batterij-oplader

Hama

Hama 210594 Handleiding

20 December 2024
Hama

Hama 210290 Handleiding

20 December 2024
Hama

Hama 201634 Handleiding

20 December 2024
NOCO

NOCO Genius GX2440 Handleiding

14 December 2024
IDX

IDX ZC-X2G Handleiding

10 December 2024
IDX

IDX UC-PD2 Handleiding

10 December 2024
Black Decker

Black Decker 98020 Handleiding

8 December 2024
Anker

Anker 613 Magnetic Wireless Charger Handleiding

7 December 2024
Ansmann

Ansmann Jump Starter 10.0 Handleiding

4 December 2024
Einhell

Einhell BT-BC 4 D Handleiding

4 December 2024