PowerWalker VI 800 CSW Handleiding

PowerWalker UPS VI 800 CSW

Lees hieronder de 📖 handleiding in het Nederlandse voor PowerWalker VI 800 CSW (4 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
ENGLISH
PowerWalker VI 600 1500 CSW-
Quick Guide
I. Overview:
1. LCD display
2. Up/down buon
3. Mute buon
4. ON / OFF buon
5. USB charging port
(5V / 2.1A shared
between 2 ports)
6. USB Communicaon
port with HID support
7. Surge protected -
outlets (no baery
backup)
8. Baery backup with
surge protected
outlets
9. RJ-45 surge protecon
(i.e. for Internet)
10. AC input
11. Venlaon and fan.
12. Circuit breaker (for
French and Schuko)
Surge protected outlets offer EMI ltering, line condioning and surge protecon, -
but they are not supported with backup power from battery in case of AC failure.
II. Operaon
Buon
Funcon
ON/OFF
buon
Press and hold the On/O Buon for 2 seconds and then release to
change state between Standby (output is o) and Line (output is on).
Mute buon
Press and hold the Mute buon for 1 second and then release to
mute or unmute the alarm.
Up/down
buon
Click to switch displayed informaon.
ENGLISH
III. Display
State
Meaning
LED
Alarm
Line /
Standby /
Baery
mode
Input voltage, input frequency, baery voltage, baery
Power, Backup me, output voltage, output frequency,
load Power and load percentage.
k: kilo, W: wa, V: voltage, A: ampere, %: percent, degC:
centigrade degree, Hz: frequency, min: minute
Line
Mode
The UPS is connected to AC input.
AVR
Mode
When the icon is ashing, the UPS is regulang the
voltage (reducing or increasing the voltage).
Baery
Mode
The UPS is running on battery
every
10 s
All Modes
The UPS alarm is disabled.
All Modes
Baery level in ranges 0 24%, 25 49%, 50 74%, and 75- - - -
100%.
Baery
Mode
Low Battery
every
0.5s
every
1s
All Modes
Load level in ranges 0-24%, 25-49%, 50-74% and 75-100%.
All Modes
Indicates overload.
every
0.5s
every
0.5s
All Modes
Baery replacement needed or the baery is not
connected
Conn
uous
every
2s
Fault
Fault code (here: E14). Check troubleshoong for details.
Connu
ous
Warning
Baery voltage is too high (i.e. wrong baery inserted)
every
1.5s
ENGLISH
IV. Baery Replacement
1. Turn o the connected equipment and unplug it
from the UPS
2. Turn o the UPS and unplug the input cable.
3. Remove two screws located on the boom of the
UPS and slide the baery cover downward, then
outward.
4. Disconnect the baery connector.
5. Slide out the exisng baery pack from the UPS
by grasping the baery pull tap.
Cauon - Do not short the posive wire and negave wire
of baery.
Cauon - DO NOT pull the baery pack out by pulling on
the baery wires.
6. Slide the new baery pack into the UPS.
7. Verify proper polarity. Re connect the baery -
connectors together.
8. Reinstall the battery cover onto the UPS. Now,
the UPS is ready for normal operaon
9. Properly dispose of the old baeries at an
appropriate recycling facility or return them to
the supplier in the packing material for the new
baeries.
Please read all of the WARNINGS and CAUTIONS in the General Manual before
replacing the baeries.
V. Troubleshoong
Fault
Event
E12
Baery mode output high (internal fault)
E14
Output short (check the loads)
E15
Output over current (too much load)
E20
Fan lock fault
E21
Over Charge Voltage (i.e. wrong baery used)
E28
Low baery voltage
E43
Overload fault
Please check hps://troubleshoot.powerwalker.com for more details.


Product specificaties

Merk: PowerWalker
Categorie: UPS
Model: VI 800 CSW
Kleur van het product: Zwart
Gewicht: 8400 g
Geluidsniveau: 40 dB
Gewicht verpakking: 8300 g
Breedte verpakking: 188 mm
Diepte verpakking: 378 mm
Hoogte verpakking: 387 mm
Gebruikershandleiding: Ja
LED-indicatoren: Ja
Vormfactor: Tower
USB-poort: Ja
Meegeleverde kabels: USB-kabel
Accu/Batterij voltage: 12 V
Aantal USB 2.0-poorten: 2
Aantal Ethernet LAN (RJ-45)-poorten: 2
Ondersteund aantal accu's/batterijen: 1
Responstijd: 6 ms
Uitgangsvermogen: 480 W
Batterij capaciteit: 9 Ah
Accu/Batterij oplaadtijd: 8 uur
Stroomspanning bescherming: Overcharge, Overload
Frequentie: 50/60 Hz
Power factor: 0.6
Stekker: C14 stekker
Producten per pallet: 75 stuk(s)
Bedrijfstemperatuur (T-T): 0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V): 0 - 90 procent
Type beeldscherm: LCD
Aantal AC uitgangen: 8 AC-uitgang(en)
Stopcontacttypes: C13 stekker
Output power capacity: 0.8 kVA
Ingang operation voltage (min): 170 V
Ingang operation voltage (max): 280 V
Uitgang operation voltage (min): - V
Uitgang operation voltage (max): 230 V
UPS-topologie: Line-interactive
Typische backup tijd op halve lading: 10 min
Typische backup tijd op volledige lading: 3 min
Uitgangsspanningsregeling: 10 procent
Golfvorm: Zuivere sinus
Automatic Voltage Regulation (AVR): Ja
USB-poorttype: USB Type-A

Heb je hulp nodig?

Als je hulp nodig hebt met PowerWalker VI 800 CSW stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding UPS PowerWalker

Handleiding UPS

Nieuwste handleidingen voor UPS