Panduit CT-160 Handleiding
Lees hieronder de đź“– handleiding in het Nederlandse voor Panduit CT-160 (2 pagina's) in de categorie Tang. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
CAUTION:
Verify power is “OFF” before working on wiring with this tool.
The plastic grips are for the user’s comfort,
and are not intended to insulate against electrical shock
while working on live electrical circuits.
CT-160
CRIMPING TOOL
OPERATION INSTRUCTIONS
10-32
.80
1.0
1.3
1.6
2.0
2
.6
MM
CUT COPPER ONL
Y
22
20
18
16
14
1
2
10
AWG
8-32
6
-32
M5
M4
M3
.5
INSULA
TION
AUTO
7
-8
MM
INS
INS
NO
N
INS
NO
N INS
12
-1 0
22
-1 4
12
-1 0
22
-1 4
CLO ESHERE
I
N
S
E
R
T
S
C
R
E
W
S
T
H
I
S
S
I
D
E
CT-160
NON-INSULATED BUTT SPLICE
INSTRUCTIONS
1. Insert stripped wire into end of the butt
splice to internal wire stop. (See product
packaging for proper strip lengths.)
2. Locate butt splice in proper non-
insulated crimp pocket.
3. Position crimp pocket on the center of
the metal barrel half with wire inserted.
4. Squeeze handles firmly.
5. Repeat for other end of butt splice.
Page: 1 of 2
PA24427A01
REV.: 02 5-2014
OPERATION INSTRUCTIONS
© Panduit Corp. 2014
CT-160
For Technical Support:
1-888-506-5400, ext. 83255
E-mail:
techsupport@panduit.com
See product packaging or contact Customer Service for
UL/CSA approved tooling/product combinations.
INSULATED BUTT SPLICE
INSTRUCTIONS
1. Insert stripped wire into end of the butt
splice to internal wire stop. (See product
packaging for proper strip lengths.)
2. Locate butt splice in proper insulated
crimp pocket.
3. Position crimp pocket on the center of
the metal barrel half with wire inserted.
4. Squeeze handles firmly.
5. Close insulation if desired.
6. Repeat for other end of butt splice.
WIRE STRIPPER for removing plastic or
rubber wire insulation. Strip length should
allow a minimum of 1/32” of conductor to
extend beyond terminal barrel.
WIRE CUTTER for No. 10 AWG and
smaller copper wire.
CUTTERS for machine screws of sizes
shown. Open handles, thread screw in this
side. Close handles to cut screw.
CRIMPING POCKETS for Pan-Term non-
insulated and insulated terminals,
disconnects, splices and wire joints on No.
22 to 10 AWG stranded wire. See product
packaging for proper crimping pockets.
This tool is made of hardened steel and is
protected with a light coat of oil.
NON-INSULATED AND INSULATED
PARALLEL SPLICE INSTRUCTIONS
1. Insert stripped wire into each end of the
parallel splice. (See product packaging
for proper strip lengths.)
2. Locate parallel splice in proper crimp
pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
CRIMP POCKET
CRIMP POCKET
CRIMP POCKET
CRIMP POCKET
NON-INSULATED
INSULATED
www.panduit.com
Page: 2 of 2
OPERATION INSTRUCTIONS
NON-INSULATED
TERMINAL AND DISCONNECT
INSTRUCTIONS
1. Insert stripped wire into terminal or
disconnect until a minimum of 1/32" of
conductor extends beyond barrel. (See
product packaging for proper strip
lengths.)
2. Locate terminal or disconnect in proper
non-insulated crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
INSULATED
TERMINAL AND DISCONNECT
INSTRUCTIONS
1. Insert stripped wire into terminal or
disconnect until a minimum of 1/32" of
conductor extends beyond barrel. (See
product packaging for proper strip
lengths.)
2. Locate terminal or disconnect in proper
insulated crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
5. Close insulation if desired.
NON-INSULATED WIRE JOINT
INSTRUCTIONS
1. Twist ends of stripped wire together,
trim and insert into wire joint. (See
product packaging for proper strip
lengths and trimming instructions.)
2. Locate wire joint in proper non-insulated
crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
INSULATED WIRE JOINT
INSTRUCTIONS
1. Twist ends of stripped wire together,
trim and insert into wire joint. (See
product packaging for proper strip
lengths and trimming instructions.)
2. Locate wire joint in proper insulated
crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
5. Close insulation if desired.
CRIMP POCKET
CRIMP POCKET CRIMP POCKET
CRIMP POCKET
CT-160
© Panduit Corp. 2014
NOTE:
In the interest of higher
quality and value, Panduit is
constantly improving and
updating our products.
Consequently, pictures herein may
vary from the actual product.
Product specificaties
| Merk: | Panduit |
| Categorie: | Tang |
| Model: | CT-160 |
Heb je hulp nodig?
Als je hulp nodig hebt met Panduit CT-160 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Tang Panduit
20 Juni 2023
12 Juni 2023
Handleiding Tang
- Tang Milwaukee
- Tang 3M
- Tang Scarlett
- Tang Monoprice
- Tang Leatherman
- Tang Gefen
- Tang Valueline
- Tang Extron
- Tang StarTech.com
- Tang PureLink
- Tang Neutrik
- Tang Dataflex
- Tang WeidmĂĽller
- Tang Fixpoint
Nieuwste handleidingen voor Tang
14 Augustus 2024
26 Juli 2024
26 Juli 2024
27 Maart 2024
27 Maart 2024
6 Januari 2024
5 Januari 2024
5 Januari 2024
4 Januari 2024
4 Januari 2024