PAC VCI-NIS2 Handleiding

PAC Niet gecategoriseerd VCI-NIS2

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC VCI-NIS2 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 53 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/1
Paciî‚¿c Accessory Corporation - Santa Ana, CA 92705
Tech Support 866-931-8021 • www.pac-audio.com
Pacific Accessory Corporation
10-06-2009
J1850
Class 2
VPW
Class 2
J1850
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
EOD
CRC
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
Class 2
Class 2
J1850
VCI-NIS2
2007-2009 Nissan & Inniti Vehicles with a color LCD screen
Inaccuracies or Typographical Errors: The information in these instruction could contain technical or other mistakes, inaccuracies or
typographical errors. PAC may make changes to the materials in these instructions at any time without notice. The information in these
instructions may be out of date, and PAC makes no commitment to update such information.
Wiring the VCI-NIS2’s power, ground and switch input wires:
1. Connecting the power supply wires: Connect the VCI-NIS2’s BLACK wire to chassis ground. Connect the RED wire to a
switched +12 volt source. The RED and BLACK wires are the ones coming out from the DC 12V side of the case.
2. Wire the VCI-NIS2’s BLUE wire the vehicle’s +12 volt reverse light supply wire. The reverse wire will show +12 volts when the
vehicle is put into reverse.
3. Connect the Video Back-up Camera’s (optional) video output to the VCI-NIS2’s Video 2 input.
(Optional: The VCI-NIS2’s Video 1 input can
be used for a second video backup camera. The toggle switch selects between the radio’s normal display or Video 1 input. Video 2 input has precedence over Video 1 input,
when the blue wire receives +12volts, regardless of the switch position.)
4. Wire the VCI-NIS2’s GREEN wire to the vehicle’s negative parking brake supply wire. The parking brake will show continuity to
ground when the parking brake is on.
5. After all connections have been veriî‚¿ed, connect the DB9 harness to the VCI-NIS2 interface and tighten the thumb screws.
Testing the VCI-NIS2:
1. Turn the vehicle and navigation unit on. The navigation display should show normal information.
* If there is no image on the display, check for correct power connection on the VCI-NIS2. Check to be sure molex connectors
are connected securely.
* If the image on the display scrolls across the screen, make sure the molex connectors are connected securely.
2. Temporarily put the vehicle into reverse being careful not to back into anything or anyone. The display screen will change to the
video back-up camera mode. Put vehicle back to Park and the navigation display should show normal information.
*If the navigation map screen disappears and you get a blank screen when the vehicle is put into reverse, check the video
back-up camera for proper power and video cable connection.
NOTE: For use ONLY in vehicles with factory installed navigation or color LCD screen.
Video input accepts only NTSC composite signal. Will NOT work with PAL signal.
Connecting the DB9 Harness:
1. Remove the factory navigation display screen.
2. Disconnect the factory 24 pin plug from the back of the factory display screen.
3. Connect the VCI-NIS2’s 24 pin plug into the back of the factory display screen.
4. Connect the factory 24 pin plug to the VCI-NIS2’s 24 pin harness.
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the VCI-NIS2 parts be held liable for consequential
damages sustained in connection with the VCI-NIS2. The manufacture and it’s distributors will not, nor will they authorize any representative or
any other individual to assume obligation or liability in relation to the VCI-NIS2 other than its replacement.
DB9 harness
Connect to
Factory Harness
Connect to
Factory Display
Black
Red
Nissan / Inî‚¿niti
Navigation Display
Green: (-) Parking Brake Signal
Blue: (+12VDC) Reverse Signal

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: VCI-NIS2

Heb je hulp nodig?

Als je hulp nodig hebt met PAC VCI-NIS2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC RP4-GM31 Handleiding

31 Augustus 2024
PAC

PAC NU-GM51 Handleiding

28 Augustus 2024
PAC

PAC NAV-1129 Handleiding

28 Augustus 2024
PAC

PAC LP7-2R Handleiding

28 Augustus 2024
PAC

PAC LP7-4 Handleiding

28 Augustus 2024
PAC

PAC GMK367B Handleiding

28 Augustus 2024
PAC

PAC CP1-FRD1 Handleiding

28 Augustus 2024
PAC

PAC C2A-CHY5 Handleiding

28 Augustus 2024
PAC

PAC NU-GM3 Handleiding

28 Augustus 2024
PAC

PAC CP1-TSL1 Handleiding

28 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024