PAC BCI-FD21 Handleiding

PAC Niet gecategoriseerd BCI-FD21

Lees hieronder de đź“– handleiding in het Nederlandse voor PAC BCI-FD21 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
Page 1
The BCI-FD21 is a camera interface that will work with vehicles with or without a factory reverse
camera. For vehicles a factory reverse camera, it will allow the addition of front and side camera with
inputs. For vehicles a factory reverse camera, it will program the factory radio to allow the without
addition of a reverse camera input and will allow the addition of front and side camera inputs.
Introduction & Features
Important Notes
1. It is very important to follow the exact sequence of installation steps as listed below. Failure to do so will result in the interface
not working as intended.
2. Installation should be done with the ignition off.
3. If you change the dip switch settings, you must disconnect and reconnect the power plug for the changes to take effect.
4. Camera inputs must be selected via dip switch setting for the interface to function properly. If not, the radio may display a blank
screen for as long as 15 seconds or display “CAMERA FAULT”. Be sure to set camera input dip switches according to your
installation.
5. This product can only be programmed to a single vehicle. If you need to install the BCI-FD21 in another vehicle it must be
unlocked from the prior vehicle first. See instructions on page 3.
Vehicle Compatibility
Product Configuration
Rev. 071 169
2013-2016
2015-2016
2013-2016
2015-2015
2013-2016
2013-2016
2013-2016
Model
Ford Fusion
Ford Mustang
Ford Taurus
Ford Transit
Lincoln MKS
Lincoln MKT
Lincoln MKX
YearModel
Ford C-MAX 2013-2015
2013-2016
2013-2015
2015-2016
2013-2016
2013-2016
2013-2016
Ford Edge
Ford Escape
Ford Expedition
Ford F-150 / Raptor
Ford Flex
Ford Focus
Year
Camera Interface for Select Ford & Lincoln Vehicles with
MyFord Touch or MyLincoln Touch 8.4” Radios
ON = Rear camera ON
OFF = Rear camera OFF
Dip 1
Camera Input Configuration
ON = Front camera ON
OFF = Front camera OFF
Dip 2
ON = Side cameras ON
OFF = Side cameras OFF
Dip 3
ON = For vehicles with OEM rear camera
OFF = For vehicles without OEM rear camera
Dip 4
ON
1 2 3 4
ON
1 2 3 4
Vehicle Configuration
See next page
LED
See
Page 4
Camera Input Configuration
See side chart
BCI-FD21
PAC | Ph. 866-931-8021 | support@pac-audio.com
© 2016 AAMP Global
www.pac-audio.com
Product Configuration (cont.)
Installation Steps
Set the dip switches for your vehicle, and the camera inputs which you wish to activate.
Set the dip switches BEFORE connecting the module to power. If a change is made to the dip switches, disconnect then
reconnect the module, for the changes to take effect.
Remove the factory radio (display) and disconnect the factory harness.
Connect the BCI-FD21-H01 harness to the back of the factory radio (display) and reconnect factory harness to the mating
connector on this harness.
Connect the aftermarket cameras to the appropriate inputs on the BCI-FD21-H02 harness.
Connect 12-volt power and ground to your aftermarket cameras. (Note: use of this 12v output can extend the life of your
cameras as it only powers the cameras when needed)
Brown Wire = 12 Volt + (2A)
Black Wire = Ground
Connect both BCI-FD21 harnesses to the BCI-FD21.
Program the BCI-FD21 to the vehicle:
• Turn the key to the RUN position.
• Once the radio is fully “booted” and on a source screen,
press and hold the Power button of the radio for 10
seconds.
• The radio will program and restart in approximately 15
seconds. Once restarted, the radio will “boot-up”, wait for
1-2 minutes until the radio is fully “booted” and on a
source screen.
• To finish programming turn off the ignition, open the
driver’s door and wait until the radio is completely off (1-2
minutes).
• Turn on the ignition and test camera functions.
1.
Note: In order for the BCI-FD21 to function, at least
camera input must be set ON in Camera Input Config
2.
3.
4.
5.
6.
7.
Vehicle Configuration Procedure:
Set dip switches per vehicle model according to chart.
Be advised that some vehicle models can have different
dip switch configurations based on the model year.
To verify if you have selected the correct dip switch
configuration for your vehicle, activate one of the turn
signals and watch the BLUE LED on the BCI-FD21.
The LED should illuminate while the turn signal is active.
If it does not, try another dip switch configuration until
you find one where the LED illuminates while the turn
signal is active.
Page 2
Rev. 071 169
PAC | Ph. 866-931-8021 | support@pac-audio.com
© 2016 AAMP Global
www.pac-audio.com
Camera Interface for Select Ford & Lincoln Vehicles with
MyFord Touch or MyLincoln Touch 8.4” Radios
BCI-FD21
Ford C-Max, Escape and Focus
Ford Expedition, Flex, Lincoln MKS and MKT
Ford Edge, F150, Fusion, Mustang, Raptor and Lincoln MKX
Vehicle Configuration (Dips 1, 2, 3)
ON
1 2 3
ON
1 2 3
ON
1 2 3 4
ON = Cannot view OE rear camera image while in
motion (up to 7mph). OFF = Can view OE rear cam in motion.
4
4
Dip 4
Power Button Location on 4 Different Vehicles
REAR CAMERA
The rear camera will be displayed automatically when vehicle is shifted into Reverse.
FRONT CAMERA
The front camera will display automatically when shifting the vehicle from Reverse into Neutral, or Drive. The front camera will be
displayed for 30 seconds, or until the vehicle is travelling at a speed of 7 mph. You can manually cancel / turn off the front camera
image by pressing the power button on the radio while it’s active.
To disable automatic front camera view when shifting from Reverse to Drive, follow these steps:
1. Place the car in Reverse
2. Press and hold the Power button for 5 seconds (the image of the rear camera may flash on the screen)
To enable automatic front camera view, repeat the steps above.
SIDE CAMERAS
The side cameras will be displayed automatically when you activate the turn signal (except in reverse).
MANUAL ACTIVATION OF CAMERA VIEWS
Press and hold the Power button for 2 seconds to access the rear camera then give a simple tap to toggle between front and rear
camera. To return to the radio screen press and hold the Power button for 2 seconds again.
Note:
During manual activation, the video display may flash momentarily when the vehicle reaches 7mph. This is normal operation.
Operation
In order to install the BCI-FD21 to another vehicle you must unlock the interface from the previous vehicle by turning off the video
input before removal.
Follow the steps below to turn off the video input:
• Turn the key to the Run position and keep it in Run position until the radio is fully “booted” and on a source screen.
• Set all the Camera Input Configuration dip switches to OFF.
• Disconnect and reconnect the BCI-FD21-H01 harness from the interface.
• Press and hold the Power button of the radio for 10 seconds.
m and restart in approximately 15 seconds.
d await until the radio is completely off (1-2 minutes).
amera input screen is displayed. If radio source screen does not
and unlocked the interface from the vehicle. You can now install
Installing the BCI-FD21 in Another Vehicle
Page 3
Rev. 071 169
PAC | Ph. 866-931-8021 | support@pac-audio.com
© 2016 AAMP Global
www.pac-audio.com
Camera Interface for Select Ford & Lincoln Vehicles with
MyFord Touch or MyLincoln Touch 8.4” Radios
BCI-FD21

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: BCI-FD21

Heb je hulp nodig?

Als je hulp nodig hebt met PAC BCI-FD21 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC NU-GM4 Handleiding

19 Februari 2025
PAC

PAC MCI-GM53 Handleiding

19 Februari 2025
PAC

PAC BCI-FD21 Handleiding

19 Februari 2025
PAC

PAC SWI-X Handleiding

19 Februari 2025
PAC

PAC GM6A-RST Handleiding

19 Februari 2025
PAC

PAC MCI-FD22 Handleiding

19 Februari 2025
PAC

PAC C2A-CHY Handleiding

19 Februari 2025
PAC

PAC OnStar OS-311 Handleiding

11 Februari 2025
PAC

PAC BT-SWC-NI1 Handleiding

11 Februari 2025
PAC

PAC APSUB-TY13 Handleiding

28 December 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

BirdDog

BirdDog Multiview Lite Handleiding

20 Februari 2025
Deye

Deye SUN-75K-SG02HP3-EU-EM6 Handleiding

20 Februari 2025
Unitech

Unitech Showcase Handleiding

20 Februari 2025
SoundTube

SoundTube DSM-16 Handleiding

20 Februari 2025
Unitech

Unitech PA768 Handleiding

20 Februari 2025
SoundTube

SoundTube CM52s-BGM Handleiding

20 Februari 2025
Celly

Celly USBCUSBC100W Handleiding

20 Februari 2025
Iluv

Iluv myPower 52 Handleiding

20 Februari 2025
Iluv

Iluv TimeShakerA Handleiding

20 Februari 2025
Iluv

Iluv i111BT Handleiding

20 Februari 2025