PAC SWI-X Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor PAC SWI-X (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
1
06-14-07
SWI-X Universal Steering Wheel Control Interface
Installation Instructions
Before You Start
A. Is this product compatible with the vehicle?
• See application guide (seperate sheet) for listing of vehicles and connection information. If not, check www.pac-
audio.com for an updated list of compatible vehicles.
B. Is this product compatible with the head unit?
• Ensure that the new head unit is capable of being operated with a remote control, and that it responds to the
remote control provided with it.
• The head unit must accept a remote control with the common carrier frequency range of 38 – 40Khz in order to
work with the SWI-X.
Note: Appendix B - Known Incompatible Aftermarket Head Certain head units will not work with the SWI-X. See
Units (page 7).
C. Prepare for the installation.
• If possible, install the SWI-X while you are installing the new head unit. Keep in mind you may need to plug in the
factory stereo to locate certain wires; therefore do not complete the head unit installation until the SWI-X is working
properly.
• Plan a general installation location for both the SWI-X LED and the control body. Keep in mind that the supplied
wire harness is , and the IR harness is .two feet long four feet long
• Use a multimeter or approved measuring device for checking vehicle circuits.
Pacific Accessory Corporatio
n
SEEK
PRES ET
AM FM
VO LUME
PLAY MUTE
0OWER
SWI-X is a learning remote.
37)8
Steering wheel
audio control wire
Aftermarket stereo must come with
a wireless remote.
2
Wiring Connections
Step 1.
Connect the BLACK
wire to ground (-).
9HUL¿FDWLRQ Wire
or location registers
a constant (-) when
probed.
Step 2.
Connect the RED wire
to switched +12V.
9HUL¿FDWLRQ Wire reg-
isters +12V when the
ignition key is turned
to the ACC or ON posi-
tions.
Step 3.
Connect the appropriate interface wire (WHITE, YELLOW, ORANGE or
GREEN).
• Refer to the . Locate the vehicle and ,GHQWL¿FDWLRQDQG&RQQHFWLRQ&KDUW
note the SWC wire color in the “Interface Wire Color” column.
1RWHWKHYHKLFOHZLUHFRORUDQGORFDWLRQLQIRUPDWLRQLQWKH³,GHQWL¿FDWLRQ´
column.
Note: You will only connect ONE of these wires. The other 3 wires will not
be used. Cut and insulate the unused wires.
• Connect the wire as indicated in the chart.
Note: Only 3 wires will be used during installation. Only GM vehicles programmed for version #4, will use 4 wires.
Step 4a.
Connect the BLUE
serial data wire.
Connect this wire
ONLY on GM
passenger vehicles (no
trucks or SUVs) with
airbags AND steering
wheel heater controls.
For all other vehicles,
cut and insulate the
BLUE wire.
Step 4b.
If instructed by the
Vehicle Application
Guide, cut the
BROWN wire loop and
insulate both halves.
Step 4c.
If instructed by the
Vehicle Application
Guide, cut the VIOLET
wire loop and insulate
both halves, or place a
resistor in-line of wires.
Note: is for vehicles made by Step 4a
General Motors that are programmed
for version #4 only. If no connections is
necessary, proceed to Step 4b.
Step 4
If necessary, perform the following operations as indicated by the notes in .,GHQWL¿FDWLRQDQG&RQQHFWLRQ&KDUW
3
06-14-07
37)8
Step 8.
To turn IR Extended Mode ON:
Press and release the program-
ming button .within 3 seconds
To leave IR Extended Mode OFF:
Do nothing for 3 seconds.
Note: To change IR Extended Mode later, restart procedure at Step 6.
Steps 11-24 (learning radio commands) must also be repeated.
37)8
37)8
37)8
Programming the SWI-X to Work With the Vehicle
Step 6.
Press and hold programming/
mode button on SWI-X. Turn the
vehicle ignition to the ON position.
Both LEDs on SWI-X
will light.
Step 7.
Release the programming/
mode button.
Both LEDs will turn
off, indicating memory
is cleared, then turn
on again for only 3
seconds.
Both LEDs will turn off.
Step 9.
Press and release the program-
ming/mode button the same
number of times as the desired
version number.
/('VZLOOÀDVKHDFK
time the button is
pressed.
After 3 seconds, LEDs
ZLOOÀDVKWRLQGLFDWHVHW
version number.
Left LED: 10’s place
Right LED: 1’s place
Step 10.
Turn vehicle ignition
to OFF position.
Programming
sequence is complete.
37)8
OFF
ACC
IGN
STRT
OFF
ACC
IGN
STRT
)73
8)73
37)8
37)8
37)8
IMPORTANT! must be completed within a certain number of seconds following the Some steps of the programming instructions
previous step. Review the complete instruction before beginning the programming sequence.
Step 5.
Refer to Appendix C - Head Units That Require IR Extended Mode On and the Vehicle Appication Guide IR Extended . Note the
Mode Setting INTERFACE Version Number and next to the selected vehicle. Fill in the information below for quick reference.
IR Extended Mode Setting: Version Number:YES / NO ____________
(Circle one) (Write Vesion Number here)


Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: SWI-X

Heb je hulp nodig?

Als je hulp nodig hebt met PAC SWI-X stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd PAC

PAC

PAC NU-GM4 Handleiding

19 Februari 2025
PAC

PAC MCI-GM53 Handleiding

19 Februari 2025
PAC

PAC BCI-FD21 Handleiding

19 Februari 2025
PAC

PAC SWI-X Handleiding

19 Februari 2025
PAC

PAC GM6A-RST Handleiding

19 Februari 2025
PAC

PAC MCI-FD22 Handleiding

19 Februari 2025
PAC

PAC C2A-CHY Handleiding

19 Februari 2025
PAC

PAC BT-SWC-NI1 Handleiding

11 Februari 2025
PAC

PAC APSUB-TY13 Handleiding

28 December 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd