PAC RP4.2-TY13 Handleiding

PAC Niet gecategoriseerd RP4.2-TY13

Lees hieronder de đź“– handleiding in het Nederlandse voor PAC RP4.2-TY13 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
Radio Replacement and
Steering Wheel Control Interface
for Select Toyota Vehicles
RP4.2-TY13
© 2022 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 1
Rev: V3
Date:032222
Introduction and Features
Important Notes
The RP4.2-TY13 interface allows the replacement of a factory radio in select Toyota vehicles and will retain factory
features such as steering wheel controls (SWC), rear camera and the factory audio ampliîšżer. This interface also allows
you to program two radio functions to each SWC button by using short press long press dual command functionality,
and also provides outputs such as: vehicle speed signal (VSS), illumination, reverse trigger and parking brake.
1. Adjustment of the vehicle settings through the original radio’s vehicle settings menu will be disabled after installation of the new
radio. It is advised to make sure all settings are as desired prior to removal of the original radio.
2. The RP4.2-TY13 does not retain Rear Seat Entertainment.
3. Speaker fading on factory amplied systems is only supported with the “amplied output” connection of the RP4.2-TY13.
4. When using real time fade, if the fader setting is biased more to the front or rear, as the radio turns on the sound may begin at the
default setting and then quickly transition to your custom setting.
5. Aftermarket radio features such as High Pass Filters (crossovers), DSP or “Network Mode” will interfere with proper fader function.
In order for the RP4.2-TY13’s fader function to work, the audio from the aftermarket radio’s output must match so it can compare the
front and rear audio levels and determine the proper fader setting for the factory ampliîšżer.
6. A USB adapter must be purchased in order to retain the factory USB port. Please refer to www.pac-audio.com to see which harness
you will need.
7. To retain AM/FM Radio and SiriusXM Radio, additional parts and adapters are required and sold separately.
Module Layout
Module Status LED
USB Status LED
Interface Connector 1
Expansion Port
Interface Connector 2
Ampliîšżed Audio Output
Non-Ampliîšżed Audio Output
Programming Button
USB Port
Radio Select DIP switches
Interface Connector 4
Ampliîšżed Audio Output Level Adjustment
Radio Replacement and
Steering Wheel Control Interface
for Select Toyota Vehicles
RP4.2-TY13
© 2022 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 2
Rev: V3
Date:032222
Interface & Harness Connections
Plug Interface Connectors 1, 2 and 4 into the appropriate ports on the RP4.2-TY13 interface (using the diagram on page 1 or the
label on the bottom of the RP4.2-TY13 module). The Connector 3 connection will be dependent upon whether or not the vehicle
has a factory ampliîšżed system. Plug Connector 3 into the appropriate port on the RP4.2-TY13; Ampliîšżed if the vehicle has a factory
ampliîšżer, Non-Ampliîšżed for base audio.
Connect the RPA-VA1 Video Adapter to the 6-pin plug on the RP4.2-TY13 harness.
Interface Connector 1 Interface Connector 2 Interface Connector 4
RPA-VA1
Interface Connector 3
Installation Steps
Purple Rear R + input
Purple / Black Rear R - input
Green Rear L + input
Green / Black Rear L - input
Gray Front R + input
Gray / Black Front R - input
White Front L + input
White / Black Front L - input
Blue / Yellow SWC Output / Key 1
Brown SWC Output / Key 2
3.5 mm Jack SWC Output
Pink Vehicle Speed
Sense Output
Light Green Parking Brake
Output
Violet / White Reverse Signal
Output
Orange / White Illumination Output
Blue / White Amp Turn On Input
Blue Not Used
1. Set the Radio Select DIP switches according to the radio you are installing.
2. Wire the aftermarket radio to the RP4.2-TY13 Interface 4 harness according to the
wiring connections chart on this page.
3. Connect the appropriate SWC Output to the aftermarket radio (if applicable).
4. Connect the OEM Camera RCA to the aftermarket radio (if applicable).
5. Once all connections have been made, connect the white, gray and black Vehicle
Connectors to the matching connectors in the vehicle.
6. Turn the ignition on. The LED on the interface will turn on and the +12v accessory
wire will turn on. For factory amplied systems, see “Testing and Verication” section
on page 5 for details on how to set the gain.
7. If the radio does not turn on and the LED on the interface is solid orange, check
the DIP switches on the side of the interface to make sure they are not all in the on
position.
8. If you wish to reassign functions to the SWC, or utilize short press, long press dual
command functionality, follow the programming instructions starting on the following
page.
Aftermarket Radio Wiring Table
Wires from Interface Connector 4
Alpine JVC Kenwood /
Lightning Audio
Clarion /
Stinger
2-Wire
Resistive
Pioneer /
Other* Sony Fusion
1 2 1 & 2 3 2 & 3 1, 2, & 3 4 1 & 4
Set DIP switches that correspond with your radio to the ON position.
Set all other DIP switches to the OFF position.
*Other - Dual / Axxera (these brands could also have 2-wire resistive), Jensen, Rockford Fosgate
Radio Replacement and
Steering Wheel Control Interface
for Select Toyota Vehicles
RP4.2-TY13
© 2022 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 3
Rev: V3
Date:032222
Default Steering Wheel Control Programming
IMPORTANT! The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require
programming unless you wish to re-assign the SWC functions or utilize short press long press dual command functionality. The
SWC can always be restored to default settings by pressing and releasing the program button on the side of the interface once
and waiting 7 seconds for the LED to ash 3 times.
Optional Steering Wheel Control Programming
If you wish to re-assign the SWC functions, utilize short press long press dual command functionality, the interface must be
programmed in the speciîšżc order shown in the chart on page 4. If you come across a function in the chart that your steering
wheel does not have, or you do not want to program, press and release the programming button on the side of the interface to
skip that function. The LED will ash off and on conrming that you have successfully skipped that function and are ready to
proceed to the next one.
Short Press Long Press Dual Command Functionality
This feature allows you to assign two aftermarket radio functions to each of the vehicles SWC buttons. It can be used with as
many of the buttons as the user likes or none at all. When this functionality is implemented, quickly pressing and releasing a
SWC button will initiate the short press command while pressing and holding a SWC button for longer than two seconds will
initiate the long press command. Please note that no long press commands are programmed by default. If you wish to assign
dual command functionality to the SWC please follow the programming steps on the next page.
Steering Wheel Controls
Default SWC Button Assignments
Alpine JVC Kenwood Clarion Pioneer Sony Fusion
Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
Mode Source Source Source Source Source Source Source
Track Up Track Up Track Up Track Up Track Up Track Up Track Up Track Up
Track Down Track Down Track Down Track Down Track Down Track Down Track Down Track Down
Voice Voice Voice Voice Voice Voice Voice Mute
Answer Receive Receive Off Hook Send Answer Answer Power
End End Reject End EndOn Hook
Reject/Source
N/P

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: RP4.2-TY13

Heb je hulp nodig?

Als je hulp nodig hebt met PAC RP4.2-TY13 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC RP4-GM31 Handleiding

31 Augustus 2024
PAC

PAC NU-GM51 Handleiding

28 Augustus 2024
PAC

PAC NAV-1129 Handleiding

28 Augustus 2024
PAC

PAC LP7-2R Handleiding

28 Augustus 2024
PAC

PAC LP7-4 Handleiding

28 Augustus 2024
PAC

PAC GMK367B Handleiding

28 Augustus 2024
PAC

PAC CP1-FRD1 Handleiding

28 Augustus 2024
PAC

PAC C2A-CHY5 Handleiding

28 Augustus 2024
PAC

PAC NU-GM3 Handleiding

28 Augustus 2024
PAC

PAC CP1-TSL1 Handleiding

28 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024