PAC RP4-VW11 Handleiding

PAC Niet gecategoriseerd RP4-VW11

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC RP4-VW11 (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/5
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-VW11
Radio Replacement & Steering Wheel Control Interface
for Volkswagen Vehicles
Rev. 011912
Introduction & Features
Important Notes
Wiring Connection Chart
The RP4-VW11 interface allows the replacement of a factory radio in select Volkswagen vehicles with LSFT-CAN databus
radios. Using this interface will retain factory features such as steering wheel controls (SWC) and the factory Volkswagen
amplier whenever the original radio is removed. The RP4-VW11 also provides data bus driven outputs such as retained
accessory power (RAP), vehicle speed sensor (VSS), illumination, reverse trigger and parking brake.
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the
interface into the vehicle (see next page for setting chart).
2. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless
you wish to re-assign the SWC functions to different buttons or assign buttons that are not pre-programmed. The SWC can
always be restored to default settings by pressing and releasing the program button on the side of the interface once and
waiting 7 seconds for the LED to ash 4 times.
3. The LED will ash whenever a user programmable SWC button is pressed.
4. The SWC will not function when car is in Accessory mode.
5. The audio screen will display When used in any of the following vehicles equipped with a Multi Function Display (MFD):
the SWC functions as they are pressed on the steering wheel. It will also display “Programming Mode” whenever the programming
button on the side of the interface is pressed. The Blue/White remote input wire must be hooked up and the MFD must be in
audio mode for these features to be displayed.
2009+ CC,
2010+ Eos, Golf, GTI, Jetta, Passat, Rabbit
2011+ Tiguan
6. The up & down arrows on the SWC that also controlWhen used in any of the following vehicles equipped with a MFD:
the MFD come programmed with functions but the SWC will control both the radio and the MFD. These buttons can be removed
by reprogramming the interface and not programming these buttons.
2006-2009 Golf, GTI, Jetta, Passat
2007-2009 Eos, Rabbit
6. In vehicles equipped with factory Bluetooth, the telematics module must be disconnected in order to use the Phone & Voice
buttons. Not disconnecting the telematics module will result in the MFD switching to phone mode every time the Phone or Voice
buttons are pressed.The telematics module can usually be found under the passenger seat.
7. The RAP feature is not available in 2010+ vehicles equipped with a premium amplied system
Red / White P.B. Output (-)
Purple / White VSS Output
Blue/White Radio On Input
Red Acc. Output (1 amp)
Orange / White Illum. Output (+)
Green Reverse Output (+)
Interface Connector
Yellow Battery +12v
Black Ground
Blue/White Amp Turn On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Vehicle Connector SWC Connector
Blu/Yel Kenwwod, Newer
JVC, OEM or
Blaupunkt
3.5mm Jack Alpine, JVC,
Clarion, Pioneer,
Sony, Valor, Boyo,
Dual, Visteon or
Advent
Page 1
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-VW11
Radio Replacement & Steering Wheel Control Interface
for Volkswagen Vehicles
Rev. 011912
Optional Steering Wheel Control Programming
IMPORTANT! The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming
unless you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by
pressing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.
In the following vehicles equipped with a MFD the screen must be set to audio mode for all buttons to program correctly.
2009+ CC,
2010+ Eos, Golf, GTI, Jetta, Passat, Rabbit
2011+ Tiguan
The OK & Back buttons can be programmed but they will also control the MFD at the same time.
2004-2010 Touareg can only program Volume Up & Down
Installation Steps
1.The radio select rotary switch on the side of the interface must be adjusted to the proper radio
setting before plugging the interface into the vehicle.
2. Make all connections as described in the connection chart on page one. Vehicles with a premium factory amplier: The factory amplier
only accepts two channels of audio input (left and right). Fading is not supported in this application. The factory amplier’s fading is controlled
by data communication from the factory radio. Neither the aftermarket radio or the RP interface have the ability to control the amplier’s fader.
3. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input)
4. If you wish to reassign functions to the SWC follow the programming instructions in the next section.
SET RADIO SELECT SWITCH
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt Clarion JVC Kenwood OEM Pioneer Valor
1 7 8 4 2 3 6 7 5
1
2
3
4
5
6
7
8
9
0
Page 2
Illustration / Schematic
Accessory Output
+12volts 1amp max.
Interface Connector
See above chart for
wire color descriptions.
Vehicle Connector
See above chart for
wire color description.
SWC Connection
See above chart for
different radio type
connections
Wiring SWC Connection
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-VW11
Radio Replacement & Steering Wheel Control Interface
for Volkswagen Vehicles
Rev. 011912
SET RADIO SELECT SWITCH
Alpine JVC Kenwood Clarion Valor OEM
A
dvent, Boyo, Dual,
Visteon, Sony Pioneer Blaupunkt
1 Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
2 Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
3 Mute Mute Mute Mute Mute Mute Mute Mute Mute
4 Preset + Source Source Source Source Source Preset + Preset + Source
5 Preset - Track + Play Search + Track + Next Preset - Preset - Track +
6 Source Track - Track + Search - Track - Previous Source Source Track -
7 Track + Band/Disc + Track - Band Up Cursor Play/Ok Track + Track + Disc +
8 Track - Preset/Disc - Disc/FM + Send/End Down Cursor Band Track - Track - Disc -
9 Power Select Disc/AM - Send Ok Up Cursor Band Band Ok
10 Enter/Play Attenuation Answer End Down Cursor Phone Menu
11 Band/Program Phone Receive BT Answer Answer Call
12 Receive Phone Reject BT Hangup End Call
13 End Voice Dial Voice Activation
14 Powe
r
Optional Programming Order
Optional Steering Wheel Control Programming (cont.)
If you wish to re-assign the SWC functions, the interface must be programmed in the specic order shown in the chart on the next
page. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and
release the program button on the side of the interface to skip that function. The LED will ash off and on conrming that you have
successfully skipped that function and are ready to proceed to the next one.
SET RADIO SELECT SWITCH
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt Clarion JVC Kenwood OEM Pioneer Valor
1 7 8 4 2 3 6 7 5
1
2
3
4
5
6
7
8
9
0
Default SWC Button Assignments
V
r
r
V
olume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
V
olume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
Phone Receive Receive Answer Send/End Source Answer Answer Source
Track + Track + Track + Track + Search + Track + Next Track + Track +
Track - Track - Track - Track - Search - Track - Previous Track - Track -
V
oice/Sta
r
Mute Mute Mute Mute Mute Mute Mute Mute
Preset Up Preset + Band Disc + N/P Cursor Up Cursor Up Preset + Disc +
Preset Down Preset - Preset + Disc - N/P Cursor Down Cursor Do
w
Preset - Disc -
OK N/P N/P N/P N/P N/P N/P N/P N/P
Back N/P N/P N/P N/P N/P N/P N/P N/P
Page 3
2
*N/P = Not programmed by default. Can be re-programmed to perform any function the user would like.

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: RP4-VW11

Heb je hulp nodig?

Als je hulp nodig hebt met PAC RP4-VW11 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC RP4-GM31 Handleiding

31 Augustus 2024
PAC

PAC NU-GM51 Handleiding

28 Augustus 2024
PAC

PAC NAV-1129 Handleiding

28 Augustus 2024
PAC

PAC LP7-2R Handleiding

28 Augustus 2024
PAC

PAC LP7-4 Handleiding

28 Augustus 2024
PAC

PAC GMK367B Handleiding

28 Augustus 2024
PAC

PAC CP1-FRD1 Handleiding

28 Augustus 2024
PAC

PAC C2A-CHY5 Handleiding

28 Augustus 2024
PAC

PAC NU-GM3 Handleiding

28 Augustus 2024
PAC

PAC CP1-TSL1 Handleiding

28 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024