PAC RP4-HD11 Handleiding

PAC Niet gecategoriseerd RP4-HD11

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC RP4-HD11 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
RP4-HD11
Radio Replacement & Steering Wheel Control Interface
for Honda Vehicles
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2013 Pacic Accessory Corporation
www.pac-audio.com
Rev. 042314
C
Page 1
Introduction & Features
Important Notes
Wiring Connection Chart
Illustration / Schematic
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the interface into the
vehicle (see next page for setting chart).
2. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless you wish
to re-assign the SWC functions or utilize short press long press dual command functionality. The SWC can always be restored to default
settings by pressing and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.
3. Vehicles equipped with factory navigation must follow the installation tech brief listed at www.pac-audio.com under the RP4-HD11 product
page.
4. Vehicles equipped with a 7” touchscreen: Once the factory head unit has been removed you will no longer be able to set the clock or date
on the factory display as this is derived from the factory head unit. The date on the screen can be permanently removed by disconnecting
the batttery to clear the screen’s memory. In order to set the clock you will need to disconnect the vehicles battery at 1:00 as this is the time
the screen defaults to once it has been reset.
5. The LED will ash whenever a SWC button is pressed.
Interface Connector Vehicle Connector SWC Connector
SWC Connection
See above chart for
different radio type
connections
Acc On/
Programming
LED
Programming
Button
Wiring SWC Connection
Red / White Parking Brake
Output (-)
Purple / White Vehicle Speed
Output
Red Accessory Output
(1 amp)
Orange / White Illumination Output
(+)
Green Reverse Output (+)
White/Green SWC Analog Input
Yellow Battery +12v
Black Ground
Orange Dimmer
Orange/White Illumination
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Blu/Yel Kenwwod, Newer
JVC
3.5mm Jack Alpine, JVC,
Clarion, Fusion,
Pioneer, Sony,
Boyo, Dual,
Lightning Audio,
Visteon or Advent
The RP4-HD11 interface allows the replacement of a factory radio in select Honda vehicles with MSCAN databus radios. Using this
interface will retain factory features such as steering wheel controls (SWC), the factory amplier and the ability to set the factory clock
when the original radio is removed. Use of this interface also allows you to program two radio functions to each SWC button by using
short press long press dual command functionality. The RP4-HD11 also provides data bus driven outputs such as accessory power,
vehicle speed sensor (VSS), illumination, reverse trigger and parking brake.
Aftermarket Radio Connections
See above chart for wire color
description.
Cut for Non-Amplied systems
Vehicle Connections
RP4-HD11
Radio Replacement & Steering Wheel Control Interface
for Honda Vehicles
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2013 Pacic Accessory Corporation
www.pac-audio.com
C
Rev. 042314
Page 2
Default Steering Wheel Control Programming
IMPORTANT! The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming
unless you wish to re-assign the SWC functions or utilize short press long press dual command functionality. The SWC can always
be restored to default settings by pressing and releasing the program button on the side of the interface once and waiting 7
seconds for the LED to ash 4 times.
Installation Steps
Default SWC Button Assignments
Alpine JVC Kenwood Clarion Pionee
r
Sony Fusion
V
olume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
V
olume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
Source Source Source Source Source Source Source Source
Track + Track + Track + Track + Search + Track + Track + Track +
Track - Track - Track - Track - Search - Track - Track - Track -
oice/Mute Mute Mute Mute Mute Mute Mute Mute
Phone Answe
r
Receive Receive Answer Send Answer Call Answer/End Audio
Phone End End Reject Voice End End Reject/Source Powe
r
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the interface
into the vehicle.
2. Make all connections as described in the chart on page 1. If there is a Premium Audio system present: Connect the RCA inputs to the
aftermarket radios pre-amp output. The audio level will vary depending on the new radios pre-amp output voltage (2-4 volts is recommended).
If there is not a Premium Audio system present: Cut the RCA inputs off and connect the aftermarket radios speaker outputs to the
remaining wire according to the chart on page 1.
3. If the vehicle is equipped with a factory subwoofer plug the RCA cables connected to the 8 pin plug into the Subwoofer or Non-Fading output
of the aftermarket radio.
4. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input).
5. If you wish to reassign functions to the SWC follow the programming instructions on the next page.
IMPORTANT! If you wish to use the Voice, Answer and End buttons you must hardwire them into the RP4-HD11. The wire you
need to connect into can be found by removing the plastic panels surrounding the steering wheel column and accessing the
connector which houses the wire (Fig. 1). Once you have located the connector you must connect into the wire located in pin
3 (Fig. 2). Wire colors are normally Blue in the Civic & Yellow in the CRV but may vary by vehicle. Connect to the RP4-HD11
interface connector as shown in Fig. 3.
SWC Plug Pin 3
8
16 9
1
Connect wire in Pin 3 to the
white/green wire in pin 5
of the RP Interface plug
Fig. 1 Fig. 2 Fig. 3
1
2
3
4
5
6
7
8
9
0
Alpine Pioneer/Other Sony FusionJVC Kenwood Clarion
1 2 3 4 7 8 9
Other = Advent, BOYO, Dual, Lightning Audio, Rockford Fosgate, Visteon
SET RADIO SELECT SWITCH
RP4-HD11
Radio Replacement & Steering Wheel Control Interface
for Honda Vehicles
Pacic Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2013 Pacic Accessory Corporation
www.pac-audio.com
Rev. 042314
C
Page 3
Optional Steering Wheel Control Programming
PLEASE NOTE: The screen on the dash can not be in the “Vehicle Menu” mode when reprogramming the SWC. If the
screen displays “Vehicle Menu”, press the Menu button on the SWC to leave this screen and ensure you are in the proper
mode before proceeding.
1. Turn the key to the ignition position.
2. Press and release programming button on the side of the interface.
3. Within 7 seconds, press the button that is to be learned on the steering wheel. The LED will turn off when the button is pressed.
At this point you have two options:
A. For short press functionality: Release the button within 1.5 seconds. The LED will turn back on.
B. For long press functionality: Hold the button until the LED starts blinking. Release the button and the LED will
go back to solid.
4. If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.
5. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and
release the program button on the side of the interface to skip that function.
6. Once programming is completed, wait seven seconds. The LED will ash three times indicating end of programming.
7. Test the interface for proper functionality. Whenever a SWC is pressed the LED on the interface should blink. If any function
does not work, repeat the programming steps
If you wish to re-assign the SWC functions or utilize short press long press dual command functionality, the interface must be
programmed in the specic order shown on the chart below. If you come across a function in the chart that your steering wheel
does not have, or you do not want to program, press and release the program button on the side of the interface to skip that
function. The LED will ash off and on conrming that you have successfully skipped that function and are ready to proceed to
the next one.
Radio Alpine JVC Kenwood Clarion Other* Pioneer Sony Fusion
1 Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
2 Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
3 Mute Mute Mute Mute Mute Mute Mute Mute
4 Preset + Source Source Source Preset + Preset + Preset + Source
5 Preset - Track + Play Search + Preset - Preset - Preset - Track +
6 Source Track - Track + Search - Source Source Source Track -
7 Track + Band/Disc + Track - Band Track + Track + Track + Audio
8 Track - Preset/Disc - Disc/FM + Send/End Track - Track - Track - Power
9 Power Select Disc/AM - Send Band Band Band
10 Enter/Play Attenuation Answer End Phone Menu
Reject Call/Source
(Bluetooth equipped
radios only)
11 Band/Program Phone Receive Voice Dial Answer Call Answer/End Call
12 Receive Phone Reject On Hook End Call
13 End Voice Dial Off Hook Voice Activation
14 Power Mute (Multimedia
units only)
*Other = Advent, Boyo, Dual, Lightning Audio, Rockford Fosgate, & Visteon
Optional Programming Order
1
2
3
4
5
6
7
8
9
0
Alpine Pioneer/Other Sony FusionJVC Kenwood Clarion
1 2 3 4 7 8 9
Other = Advent, BOYO, Dual, Lightning Audio, Rockford Fosgate, Visteon
SET RADIO SELECT SWITCH

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: RP4-HD11

Heb je hulp nodig?

Als je hulp nodig hebt met PAC RP4-HD11 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC RP4-GM31 Handleiding

31 Augustus 2024
PAC

PAC NU-GM51 Handleiding

28 Augustus 2024
PAC

PAC NAV-1129 Handleiding

28 Augustus 2024
PAC

PAC LP7-2R Handleiding

28 Augustus 2024
PAC

PAC LP7-4 Handleiding

28 Augustus 2024
PAC

PAC GMK367B Handleiding

28 Augustus 2024
PAC

PAC CP1-FRD1 Handleiding

28 Augustus 2024
PAC

PAC C2A-CHY5 Handleiding

28 Augustus 2024
PAC

PAC NU-GM3 Handleiding

28 Augustus 2024
PAC

PAC CP1-TSL1 Handleiding

28 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024