PAC RP4-CH21 Handleiding

PAC Niet gecategoriseerd RP4-CH21

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC RP4-CH21 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Pacic Accessory Corporation

® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com

www.pac-audio.com

RP4-CH21

Radio Replacement & Steering Wheel Control Interface

for Dodge/Jeep/Ram Vehicles

Rev. 043014

Page 1

Introduction & Features

Important Notes

The RP4-CH21 interface allows the replacement of a factory radio in select Dodge/Jeep/Ram vehicles with MS-CAN

databus radios. Using this interface will retain factory features such as steering wheel controls (SWC), HVAC controls,

Driver Information Center (DIC), vehicle settings, vehicle safety features and the factory audio amplier whenever the

original radio is removed. Use of this interface also allows you to program two radio functions to each SWC button by

using short press long press dual command functionality. The RP4-CH21 also provides data bus driven outputs such as

retained accessory power (RAP), vehicle speed sensor (VSS), illumination, reverse trigger and parking brake.

1. Please make your vehicle settings selections before removing the factory radio for optimal installation time. Once the radio has

been removed, the vehicle settings which are normally selected through the factory radio can be accessed by downloading

and installing the PAC Vehicle Settings program from . A PAC-UP is http://www.pac-audio.com/rmware/RP/index.html

required to connect with the interface. Please see page 6 for further details on the vehicle settings app.

2. Vehicles with a factory amplier: The factory amplier only accepts two channels of audio input (left and right). Fading is

not supported in these applications. The factory amplier’s fading is controlled by data communication from the factory radio.

Neither the aftermarket radio or the RP interface have the ability to control the amplier’s fader.

3. Vehicles equipped with VES: Retention of the VES system is not currently supported

4. The active guide lines for the factory reverse camera can be turned off and on in the vehicle settings app referenced above.

5. In vehicles equipped with the 8.4” uConnect system, the factory compass display on the DIC, 911 assist, WiFi hotspot and

uConnect access will be lost.

6. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the

interface into the vehicle (see next page for setting chart).

7. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless

you wish to re-assign the SWC functions or utilize short press long press dual command functionality. The SWC can always

be restored to default settings by pressing and releasing the programming button on the side of the interface once and waiting

7 seconds for the LED to ash 4 times.

8. The LED will ash whenever a programmable SWC button is pressed.

9. uConnect is not retained when using this interface

10. RAM Promaster equipped with a single DIN radio is not compatible

11. Dodge Durango - You will lose the button from radio to ip down third row headrests. Users will have to control rear climate

controls from the controls located in the rear roof. Ventilated seats are not supported.

12. Jeep Grand Cherokee: Ventilated seats are not supported

13. Jeep Cherokee: Ventilated seats are not supported

14. All vehicle settings will be retained, however the following settings are not adjustable once the factory radio is removed:

• RAM Trucks/Grand Cherokee/Durango

• Fuel Saver Display

• Air Suspension Settings

• Forward Collision Warning with Crash Mitigation

• Cherokee (With Technology Package)

• Adaptive Cruise Control with Stop and Go

• Advanced Brake Assist

• Automatic High Beam Headlamp Control

• Blind Spot and Cross Path Detection

• Forward Collision Warning with Crash Mitigation

• LaneSense Lane Departure Warning

• Parallel and Perpendicular Park Assist

• Rain Sensitive Windshield Wipers

• Tilting Side Mirrors While in Reverse

• Power Lift Gate Chime

Pacic Accessory Corporation

® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com

www.pac-audio.com

RP4-CH21

Radio Replacement & Steering Wheel Control Interface

for Dodge/Jeep/Ram Vehicles

Rev. 043014

Page 4

Optional Steering Wheel Control Programming (cont)

Radio Alpine JVC Kenwood Clarion Other* Pioneer Sony Fusion

1 Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +

2 Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -

3 Mute Mute Mute Mute Mute Mute Mute Mute

4 Preset + Source Source Source Preset + Preset + Preset + Source

5 Preset - Track + Play Search + Preset - Preset - Preset - Track +

6 Source Track - Track + Search - Source Source Source Track -

7 Track + Band/Disc + Track - Band Track + Track + Track + Audio

8 Track - Preset/Disc - Disc/FM + Send/End Track - Track - Track - Power

9 Power Select Disc/AM - Send Band Band Band

10 Enter/Play Attenuation Answer End Phone Menu

Reject Call/Source

(Bluetooth equipped

radios only)

11 Band/Program Phone Receive Voice Dial Answer Call Answer/End Call

12 Receive Phone Reject On Hook End Call

13 End Voice Dial Off Hook Voice Activation

14 Power Mute (Multimedia

units only)

*Other = Advent, Boyo, Dual, Lightning Audio, Rockford Fosgate, & Visteon

Optional Programming Order

Programming

1. Turn the key to the ignition position.

2. Press and release programming button on the side of the interface.

3. Within 7 seconds, press the button that is to be learned on the steering wheel. The LED will turn off when the button is pressed.

At this point you have two options:

A. For short press functionality: Release the button within 1.5 seconds. The LED will turn back on.

B. For long press functionality: Hold the button until the LED starts blinking. Release the button and the LED will

go back to solid.

4. If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.

5. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and

release the program button on the side of the interface to skip that function.

6. Once programming is completed, wait seven seconds. The LED will ash three times indicating end of programming.

7. Test the interface for proper functionality. Whenever a SWC is pressed the LED on the interface should blink. If any function

does not work, repeat the programming steps

Alpine JVC Kenwood Clarion Pioneer/Other Sony Fusion

1 2 3 4 7 8 9

Other = Advent, BOYO, Dual, Lightning Audio, Rockford Fosgate, Visteon

SET RADIO SELECT SWITCH

RP4-CH21 SWC Notes

1. In vehicles that do not have SWC for the radio but do have

SWC for the menu you can program the up/down/left/right

arrows to whatever you want. We recommend that you

have the DIC in the speedometer screen when using the

SWC for the radio (Fig.1)

2. The Mute, Answer and End buttons in the Ram Promaster

can not be programmed for long press functionality.

Fig. 1

Pacic Accessory Corporation

® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com

www.pac-audio.com

RP4-CH21

Radio Replacement & Steering Wheel Control Interface

for Dodge/Jeep/Ram Vehicles

Rev. 043014

Page 5

Testing & Verication

1. Turn the ignition on. The LED on the interface will turn on & the +12v accessory wire will turn on.

2. Turn on the radio & check balance & fade. Note: will not fade as neither the aftermarket radio Factory amplied Systems

or the RP interface have the ability to control the amplier’s fader.

3. Verify that the factory subwoofer (if present) is playing

4. Verify that all SWC are functioning properly.

5. Turn off vehicle & remove key. RAP will be active & keep the radio on for up to 10 minutes (depending on the user

programmed vehicle setting) or until the drivers door is opened.

6. The LED & radio will turn off when RAP turns off or the drivers door is opened.

Additional Controls

When replacing the radio in the following vehicles you may lose some of the climate control features that the factory radio provides:

Grand Cherokee, Cherokee, Ram & Durango. The RP4-CH21 retains those features by integrating them into the existing factory

buttons and displaying the information on the DIC. PLEASE NOTE: The DIC must be set to Audio mode in order for the HVAC

information to be displayed.

The following buttons have been re-purposed from their original OEM function to retain key HVAC controls that are missing when

removing the factory radio:

• Mute Button - Sets Max A/C On/Off

• Enter Button - Locks out rear zone climate controls (Durango only)

• Screen Off Button - Sets fan position (Defrost/Vents/Floor)

• Back Button - Syncs temperatures for dual zone climate controls

• The lock buttons on the doors control their respective seat heaters. Press and hold lock for 2 seconds to engage seat heater.

Press lock again to change from high/low/off. The status will displayed on DIC.

• The assist button on mirror turns heated steering wheel on/off. The status will displayed on DIC.

• HVAC buttons that remain retain their original OEM functionality

Volume Knob & Tune Knob - Work one for one with the SWC

Mute Button –

Sets Max A/C. On/O

Screen O Button -

Sets fan position.

Back - Sync temps

for dual zone climate

control.

Enter - Locks out rear

zone climate control.

Setting the Clock in the Promaster (Must be done with radio off)

1. Press and hold volume down on the SWC.

2. While holding volume down, use the track up/down buttons on the SWC to adjust the time.

Setting the Date in the Promaster

1. Press and hold volume up on the SWC.

2. While holding volume up, use the track up/down buttons on the SWC to adjust the date.

3. The 12/24 hour setting will have to be adjusted using the vehicle settings app referenced on the next page.

Product specificaties

Merk:	PAC
Categorie:	Niet gecategoriseerd
Model:	RP4-CH21

Heb je hulp nodig?

Als je hulp nodig hebt met PAC RP4-CH21 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd PAC

PAC RP4-GM31 Handleiding

31 Augustus 2024

PAC NU-GM51 Handleiding

28 Augustus 2024

PAC NAV-1129 Handleiding

28 Augustus 2024

PAC LP7-2R Handleiding

28 Augustus 2024

PAC LP7-4 Handleiding

28 Augustus 2024

PAC GMK367B Handleiding

28 Augustus 2024

PAC CP1-FRD1 Handleiding

28 Augustus 2024

PAC C2A-CHY5 Handleiding

28 Augustus 2024

PAC NU-GM3 Handleiding

28 Augustus 2024

PAC CP1-TSL1 Handleiding

28 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024