PAC RP4-AD11 Handleiding

PAC Niet gecategoriseerd RP4-AD11

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC RP4-AD11 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 225 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
Paciîš¿c Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-AD11
Radio Replacement & Steering Wheel Control Interface
for Audi Vehicles
Rev. 011312
Introduction & Features
Important Notes
Wiring Connection Chart
Illustration / Schematic
The RP4-AD11 interface allows the replacement of a factory radio in select Audi vehicles with LSFT-CAN databus radios.
Using this interface will retain factory features such as steering wheel controls (SWC) and the factory audio ampliîš¿er
whenever the original radio is removed. The RP4-AD11 also provides data bus driven outputs such as retained accessory
power (RAP), vehicle speed sensor (VSS), illumination, reverse trigger and parking brake.
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the
interface into the vehicle (see next page for setting chart).
2. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless
you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by pressing
and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.
3. The LED will ash whenever a SWC button is pressed.
Red / White P.B. Output (-)
Purple / White VSS Output
Red Acc. Output (1 amp)
Orange / White Illum. Output (+)
Green Reverse Output (+)
Interface Connector
Yellow Battery +12v
Black Ground
Blue/White Amp Turn On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Vehicle Connector
SWC Connector
Blu/Yel Kenwwod, Newer
JVC, OEM or
Blaupunkt
3.5mm Jack Alpine, JVC,
Clarion, Pioneer,
Sony, Valor, Boyo,
Dual, Visteon or
Advent
Accessory Output
+12volts 1amp max.
Interface Connector
See above chart for
wire color descriptions.
Vehicle Connector
See above chart for
wire color description.
SWC Connection
See above chart for
different radio type
connections
Wiring
SWC Connection
Page 1
Paciîš¿c Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-AD11
Radio Replacement & Steering Wheel Control Interface
for Audi Vehicles
Rev. 011312
Optional Steering Wheel Control Programming
IMPORTANT! The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming
unless you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by
pressing the program button on the side of the interface once and waiting for the timeout.
SET RADIO SELECT SWITCH
Installation Steps
1.The radio select rotary switch on the side of the interface must be adjusted to the proper radio
setting before plugging the interface into the vehicle (see page 2 for setting chart).
2. Only one of the two provided radio harnesses will be used. Remove the factory installed radio to determine the correct harness for your
particular vehicle.
3. Make all connections as described in the connection chart on page 1. Vehicles without a factory amplier: Connect the aftermarket radio’s
front and rear speaker wires to the vehicle connector. Vehicles with a factory ampliîš¿er: To determine whether the ampliîš¿er needs RCA or
speaker level input, check the OEM side of the 22/20 pin plug to see if the speaker wires are populated. If so hook the front speaker outputs to
the 22/20 pin plug and the rear RCA outputs to the 12 pin plug (dock-n-lock connector) or 20 pin plug (ISO Connector). If there are no factory
speaker wires located in the OEM 22/20 pin plug then you will need to hook all 4 of the aftermarket radios RCA outputs to the 12/20 pin plug.
The blue RCA has no function at this time (dock-nlock connector only).
4. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input)
5. If you wish to reassign functions to the SWC follow the programming instructions in the next section.
If you wish to re-assign the SWC functions, the interface must be programmed in the speciîš¿c order shown in the chart on the next
page. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and
release the program button on the side of the interface to skip that function. The LED will ash off and on conrming that you have
successfully skipped that function and are ready to proceed to the next one.
SET RADIO SELECT SWITCH
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt Clarion JVC Kenwood OEM Pioneer Valor
1 7 8 4 2 3 6 7 5
1
2
3
4
5
6
7
8
9
0
SET RADIO SELECT SWITCH
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt Clarion JVC Kenwood OEM Pioneer Valor
1 7 8 4 2 3 6 7 5
1
2
3
4
5
6
7
8
9
0
Default SWC Button Assignments
Alpine JVC Kenwood Clarion
V
alo
r
OEM Sony/Pionee
r
Blaupunkt
olume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
V
olume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
Mode Source Source Source Source Source Source Source Source
Track + Track + Track + Track + Search + Track + Next Track + Track +
Track - Track - Track - Track - Search - Track - Previous Track - Track -
V
oice/Phone Mute Mute Mute Mute Mute Mute Mute Mute
V
olume Wheel Preset + Band Disc + Band Cursor Up Play/OK Preset + Disc +
Track Wheel Preset - Preset + Disc - Send/End Cursor Down Band Preset - Disc -
Page 2
Paciîš¿c Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-AD11
Radio Replacement & Steering Wheel Control Interface
for Audi Vehicles
Rev. 011312
Alpine JVC Kenwood Clarion Valor OEM
A
dvent, Boyo, Dual,
Visteon, Sony Pioneer Blaupunkt
1 Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
2 Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
3 Mute Mute Mute Mute Mute Mute Mute Mute Mute
4 Preset + Source Source Source Source Source Preset + Preset + Source
5 Preset - Track + Play Search + Track + Next Preset - Preset - Track +
6 Source Track - Track + Search - Track - Previous Source Source Track -
7 Track + Band/Disc + Track - Band Up Cursor Play/Ok Track + Track + Disc +
8 Track - Preset/Disc - Disc/FM + Send/End Down Cursor Band Track - Track - Disc -
9 Power Select Disc/AM - Send Ok Up Cursor Band Band Ok
10 Enter/Play Attenuation Answer End Down Cursor Phone Menu
11 Band/Program Phone Receive BT Answer Answer Call
12 Receive Phone Reject BT Hangup End Call
13 End Voice Dial Voice Activation
14 Powe
r
Optional Programming Order
Optional Steering Wheel Control Programming (cont.)
Step B.
Press and
hold the
programming
button.
Step C.
Release the
programming
button. The
LED will turn
back on.
LED will turn off.
Step A.
Turn the vehicle ignition to
the ON position.
OFF
ACC
IGN
STRT
Step E.
Release the button.
The LED will turn on
back on.
Step D.
Within 7 seconds,
press and release the
button that is to be
learned on the steering
wheel.
The LED will
turn off during
this process.
VOL
VOL
Step F.
If you need to program more buttons,
repeat steps D & E for each additional
audio function on the steering wheel.
Program
remaining buttons
x4
Once programming is
completed, . wait 7 seconds
The LED will ash four
times indicating the end of
programming.
Step G.
After all buttons are
programmed
Page 3
2

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: RP4-AD11

Heb je hulp nodig?

Als je hulp nodig hebt met PAC RP4-AD11 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC RP4-GM31 Handleiding

31 Augustus 2024
PAC

PAC NU-GM51 Handleiding

28 Augustus 2024
PAC

PAC NAV-1129 Handleiding

28 Augustus 2024
PAC

PAC LP7-2R Handleiding

28 Augustus 2024
PAC

PAC LP7-4 Handleiding

28 Augustus 2024
PAC

PAC GMK367B Handleiding

28 Augustus 2024
PAC

PAC CP1-FRD1 Handleiding

28 Augustus 2024
PAC

PAC C2A-CHY5 Handleiding

28 Augustus 2024
PAC

PAC NU-GM3 Handleiding

28 Augustus 2024
PAC

PAC CP1-TSL1 Handleiding

28 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024