PAC OnStar OS-3BOSE Handleiding

PAC Niet gecategoriseerd OnStar OS-3BOSE

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC OnStar OS-3BOSE (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
Paci c Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com Page 1
11-01-06
The OS-3BOSE is a plug and play interface that allows replacement of a General Motors GMLAN factory radio. It will
maintain operation of the OnStar® system, Bose® amplifi er and speakers. The OS-3BOSE has on board switching
to allow audio from the OnStar® system to play through the two front factory speakers when OnStar® is active. This
interface retains all warning chimes, the audible turn signal indicators, and the Vehicle Rear Parking Assist System (if
equipped). Rear Seat Audio headphone jacks will also remain active and are designed for use with dual zone radios.
Step 1- Pre wire the RAD-18 wire harness to the aftermarket stereo wire harness. Refer to installation notes on page 3 for special instruc-
tions
Step 2- After connecting the RAD-18 and OS-GM14 wire harness to the OS-3BOSE main interface, connect the OS-GM14 connector to
the factory harness.
OS-3BOSE
General Motors Bose® and OnStar® Interface
Installation Instructions for GMLAN Vehicles
Pacific Accessory Corporation
Pacific Accessory Corporation
The Following General Motors Vehicles using the GMLAN Data Bus
Chevrolet: Suburban (2007) Tahoe (2007) Avalanche (2007) Monte Carlo (2006-2007) Silverado - not classic (2007) Impala (2006-2007)
GMC: Acadia (2007) Yukon Denali (2007) Yukon (2007) Sierra - not classic (2007)
Cadillac: Escalade - including ESV and EXT (2007)
Buick: Lucerne (2006-2007)
1. The OS-3BOSE does not retain the factory XM receiver. You will lose the XM option when the factory radio is replaced with an aftermar-
ket radio.
2. You may use this interface if the vehicle does not have OnStar® but you need to interface with the Bose® ampli er.
3. If you are not retaining the Bose® ampli er, use the OS-3 interface instead of this OS-3BOSE interface.
4. This interface retains the 5.1 audio system in the Cadillac Escalade.
5. Built in Smart Mute Circuitry will play OnStar® through the front speakers and allow the Rear Seat Audio jacks to continue playing the
source selected at the radio.
• OnStar® active LED and Ignition on LED.
• Provides +12v switched accessory output. No more searching for switched +12v in fuse box or kick panel.
• OnStar® Volume control via factory steering wheel audio controls on Premium Bose® vehicles. Steering wheel radio controls can be
retained to control new radio by using the SWI - X, JACK, ECL2 or PS.
• New radio will operate with the vehicle RAP (Retained Accessory Power) system. The radio stays on after the key is turned off and stays
on for approximately 10 minutes or until the drivers door is opened.
1
1
0
0 0
0
0
0
1
1
1
0
0
0
1
1
1
1 0
0
0
0
0 0
1
1
1
1 0
0
1
1 0
0 1
0 0
0 0
1
0
1 0
1
0 0
1
0
0
a
C
a
Note: The Blue/White remote wire must be connected to the new radios amp remote turn on wire.
The Lt. Green wire is a SWC output wire. Do not connect this wire to anything other than the green interface wire of a SWI - X, ALP, ECL,
or PS. Program the SWC interface for version #2 and do not cut the Brown SWI interface loop. When pushing the steering wheel buttons
during programming, a simple press and release of the button will do just  ne, no need to hold. The rear controls (if equipped) will perform
the same functions as the steering wheel buttons without any additional programming necessary. If steering wheel controls are not retained
or present, isolate this wire and do not use!
Wire locations and Description
WIRE COLOR CIRCUIT CIRCUIT WIRE COLOR
9 18
8 17
7 16
6 15
5 14
4 13
3 12
2 11
1 10
PIN NUMBER
SWC Output
Chime Module
White/Black
Grey/Black
Green/Black
Purple/Black
Black
Lt. Green
Orange
Blue/White
Red
Left Front(-)
Right Front (-)
Left Rear (-)
Right Rear(-)
Ground
Illumination
Amp Turn On
+12v Accessory Output
Left Front (+)
Right Front (+)
Left Rear (+)
Chime Module
Right Rear (+)
+12v Constant
White
Grey
To CM - X
Green
To CM - X
Purple
Yellow
N/A
N/A
Not Used
Not Used
WIRE COLOR CIRCUIT CIRCUIT WIRE COLOR
Orange Illumination
8 16
Purple/White GMLan
7 15
+12v Constant Yellow
Black Ground
6 14
Amplifier Turn On Blue
Purple/Black Right Rear (-)
5 13
Right Rear (+) Purple
Green/Black Left Rear (-)
4 12
Left Rear (+) Green
OnStar Mono(-)
3 11
OnStar Mono(+)
Grey/Black Right Front (-)
2 10
Right Front (+) Grey
White/Black Left Front (-)
1 9
Left Front (+) White
PIN NUMBER
Purple/WhiteWhite/Brown
Amp Control Black
RAD - 18
OS-GM14
Notes
Supported Vehicles
Installation
Paci c Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com Page 2
11-01-06
Step 3- The CM-X is not needed when the Premium Ampli er is retained. The door chimes and audible turn signal indicators are generated
from the Bose® ampli er.
Step 4- OnStar volume can be adjusted from the steering wheel buttons when OnStar is activated (with premium Bose ampli er ® ® ®
ONLY). Turn the OnStar volume adjustment on the interface all the way up.®
Step 5- This ampli er will allow the fader and balance to work correctly. You can also use the supplied brown connector, c4, for subwoofer
control and center channel operation. These are low level mono inputs. We recommend using the center channel only if a 5.1 chan-
nel audio processor (or a dedicated center channel output) is present.
102.7 FM
Aftermarket stereo
30
8586
87
87a
Red wire to accessory
input of radio
c2
c1
OS-GM14 Harness
OnStar
Active
®
Volume
Adjust
SWC output wire
Connect to SWI - X green wire
Program for Version # 2
RAD 18
L
t
G
r
e
e
n
W
i
r
eOS - 3 BOSE
General Motors GMLan OnStar Interface®
Factory Radio Replacement
Retention of Bose Amplifier and OnStar Option® ®
Ignition
On LED
Pacific Accessory Corporation Santa Ana, Ca 92705
The CM-X is not
needed when a
Premium Amplifier
is retained
c4
(Brown)
Center
channel
sepaker
(RED) Subwoofer
(WHITE)
Step 3- The CM-X is not needed when the Premium Ampli er is retained. The door chimes and audible turn signal indicators are generated
from the Bose® ampli er.
Step 4- OnStar volume can be adjusted from the steering wheel buttons when OnStar is activated (with premium Bose ampli er ® ® ®
ONLY). Turn the OnStar volume adjustment on the interface all the way up.®
Note - Due to the design of this Premium Bose amplifi er system, there is currently no way of fading from front to rear with an ®
aftermarket radio.
102.7 FM
Aftermarket stereo
30
85
86
87
87a
Red wire to accessory
input of radio
c2
c1
OS-GM14 Harness
OnStar
Active
®
Volume
Adjust
SWC output wire
Connect to SWI - X green wire
Program for Version # 2
RAD 18
L
t
G
r
e
e
n
W
i
r
eOS - 3 BOSE
General Motors GMLan OnStar Interface®
Factory Radio Replacement
Retention of Bose Amplifier and OnStar Option® ®
Ignition
On LED
Pacific Accessory Corporation Santa Ana, Ca 92705
The CM-X is not
needed when a
Premium Amplifier
is retained
Step 3- The CM-X should be plugged into the white 2-pin connector and permanently mounted. This module will retain all warning chimes
and audible turn signal indications. There is no volume adjustment for this feature so keep that in mind when choosing a mounting
location.
Step 4- This ampli er will allow the fader to work correctly.
Step 5- ®The OnStar volume is only able to be controlled from the adjustment screw on the interface. Make sure this is set to the desired
level before mounting the interface and reassembling the dash.
102.7 FM
Aftermarket stereo
30
8586
87
87a
Red wire to accessory
input of radio
c2
c1
OS - GM14 Harness
OnStar
Active
®
Volume
Adjust
OS - 3 BOSE
General Motors GMLan OnStar Interface®
Factory Radio Replacement
Retention of Bose Amplifier and OnStar Option® ®
Ignition
On LED
Pacific Accessory Corporation Santa Ana, Ca 92705
RAD-18
CM-X
O
Chime Module
SWC output wire
Connect to SWI - X green wire
Program for Version # 2
L
t
G
r
e
e
n
W
i
r
e
Standard Bose®: Connecting to the vehicle’s Bose® ampli er (All Other Listed Vehicles)
Premium Bose®: Connecting to the vehicle’s Bose® ampli er (Denali Only)
Premium Bose®: Connecting to the vehicle’s Bose® ampli er (Escalade Only)
Pacic Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com Page 3
11-01-06
On
These Buttons will
perform the
same function as the
Steering Wheel
Buttons do (when
a SWC interface
is used)
Turns the
Rear Seat
Audio on
and off
1. Turn ignition on. The red ignition On LED inside the interface will turn on and the +12v accessory wire will turn on.
2. Turn on the radio and check balancing and fading. Note: amplier will not fade as the rear outputs of after-The Denali Premium Bose®
market radio do not adjust the amplier.
3. Pressing the OnStar® button will turn off the rear speakers and allow the OnStar® audio to be heard in the two front speakers. The
OnStar® active red LED will also turn on. When OnStar® disconnects, the radio will un-mute or turn back on and the OnStar® LED will
turn off.
4. Turn off vehicle and remove key. RAP will be active and keep the radio on for 10 minutes or until the drivers door is opened.
5. The green LED and radio will turn off when RAP turns off or the drivers door is opened.
6. Pressing the Mute/OnStar® button on the steering wheel for 1.5 seconds will activate Onstar®.
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the OS-3BOSE parts be held liable for consequential damages
sustained in connection with the OS-3BOSE. The manufacture and it’s distributors will not, nor will they authorize any representative or any other
individual to assume obligation or liability in relation to the OS-3BOSE other than its replacement.
OnStar® is a registered trademark of OnStar® Corporation.
Bose® is a registered trademark of Bose®
The headphone jacks will play the rear zone source selected by the head unit (refer to the new radios instruction manual for details on this
feature if equipped). Maximize the rear zone volume level (this will reduce unwanted noise). During an Onstar call the front speakers play
OnStar, the rear speakers are muted and the headphones will continue to play the rear zone audio source.
Notes: When the Rear Seat Audio jacks are activated in any vehicle OTHER than the Cadillac Escalade or GMC Yukon Denali the rear
speakers will mute.
Installation Notes
1. When the interface is connected to the vehicle for the rst time the car must be started so all vehicle features are recognized by our inter-
face.
2. If using a Navigation radio or other high current DVD LCD radio, do not connect the +12 volt constant and ground wires from the RAD-18
to your new radio. Jump these wires from the OS-GM14 to the new radio (refer to pin description on page 1 for wire locations).
3. DO NOT cut the Brown loop on the SWI interface connector. Program the Interface for version # 2.
Instructions for using the Rear Seat Audio jacks with a Dual Source head unit
Testing and Verifying Operation
30
85
86
87
87a
c2
c1
OS-GM14 Harness
OnStar
Active
®
Volume
Adjust
OS - 3 BOSE
General Motors GMLan OnStar Interface®
Factory Radio Replacement
Retention of Bose Amplifier and OnStar Option® ®
Ignition
On LED
Do not use
Yellow and
Black wires
from the interface
Pacific Accessory Corporation Santa Ana, Ca 92705
Tap onto the Yellow
and Black wires
RAD-18
Navigation or
LCD TV
Radio
Relay for Acc.
voltage

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: OnStar OS-3BOSE

Heb je hulp nodig?

Als je hulp nodig hebt met PAC OnStar OS-3BOSE stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC RP4-GM31 Handleiding

31 Augustus 2024
PAC

PAC NU-GM51 Handleiding

28 Augustus 2024
PAC

PAC NAV-1129 Handleiding

28 Augustus 2024
PAC

PAC LP7-2R Handleiding

28 Augustus 2024
PAC

PAC LP7-4 Handleiding

28 Augustus 2024
PAC

PAC GMK367B Handleiding

28 Augustus 2024
PAC

PAC CP1-FRD1 Handleiding

28 Augustus 2024
PAC

PAC C2A-CHY5 Handleiding

28 Augustus 2024
PAC

PAC NU-GM3 Handleiding

28 Augustus 2024
PAC

PAC CP1-TSL1 Handleiding

28 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024