PAC OEM-2 Handleiding

PAC Niet gecategoriseerd OEM-2

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC OEM-2 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Pacic Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705

techsupport@pac-audio.com • Voice: (800) 854-3133 • Fax: (800) 832-9722 • www.pac-audio.com

rev. 06-11-2007

Page 1

The OEM-2 may be used in any one of four possible congurations and system types.

1) Replacing a premium factory radio with an aftermarket stereo and use the factory amplier and speakers.

2) Four channel line out converter for adding ampliers to a standard factory speaker system.

3) Adding aftermarket ampliers to a factory premium amplied system (Bose, JBL, etc.).

4) Installing a radio with oating ground speaker outputs to a common grounded speaker system like the early Fords.

The OEM-2 also includes a remote turn-on for ampliers or a power antenna, providing 2 amps at 12 volts when 0.8 volts or greater is applied to the input side. This

is useful for low voltage triggers like those used in Fords or for automatic triggering when audio is present. The output “turn on” is delayed 1 second to prevent turn

on pops.

OEM – 2

Universal sound system interface and controller

White

LF (+) speaker (high power) White

LF (+) low level output

White/red

LF (+) speaker (low power) White/red LF (+) common gnd. speaker output

White/black

LF (–) common White/black

LF (–) common

Gray

RF (+) speaker (high power) Gray

RF (+) low level output

Gray/red

RF (+) speaker (low power) Gray/red RF (+) common gnd. speaker output

Gray/black

RF (–) common Gray/black

RF (–) common

Green

LR (+) speaker (high power) Green

LR (+) low level output

Green/red

LR (+) speaker (low power) Green/red LR (+) common gnd. speaker output

Green/black

LR (–) common Green/black

LR (–) common

Violet

RR (+) speaker (high power) Violet

RR (+) low level output

Violet/red

RR (+) speaker (low power) Violet/red RR (+) common gnd. speaker output

Violet/black

RR (–) common Violet/black

RR (–) common

Yellow

Constant battery Yellow Constant battery

Red

Switched power Red Switched power

Black

Gnd. neg. power Black Gnd. neg. power

Blue

Power antenna turn on Blue Power antenna turn on

Blue/white

Amplifier remote turn on 0.8 v min. Blue/white Amplifier remote turn on 2 amps max.

Orange

Illumination dimming Orange Illumination dimming

Input wiring colors Output wiring colors

1 Connect these wires to an aftermarket radio (+) high power speaker output (typically 20 watts x 4 and higher).

2 Connect these wires to an aftermarket radio (+) low power speaker output. (All stereos up to 20 watts x 4 or when wiring for #4)

3 If the radio is high power (oating ground), connect these wires separately to each of the radio’s speaker (-) wire (do not connect (-) speaker wires together). If the

radio has a common ground speaker outputs, connect these wires together along with the radio’s speaker ground.

4 These wires go directly through to the outputs for convenience of wiring. The red and black wires supply power to the internal low voltage trigger.

5 This wire needs only a minimum of 0.8 volts to supply 12 volts on the blue/white wire on the output side of the OEM-2.

6 For convenience, the positive leads of the RCA are connected internally to these wires.

7 For convenience, the grounds of the RCA are connected internally to these wires. Not used with common grounded speakers.

Note: Some Chrysler/Dodge vehicles with a Innity premium sound system do not need any interface. If the speakers fade and balance correctly with this interface

installed, but you have very little volume, then you do not need this interface.

Referring to the wire color chart above, connect the speaker outputs of the new radio to the OEM-2, using the positive, solid color, and the negative black-striped

wires for all four channels. On the output side of the OEM-2 connect the solid color wires (+) and the black-striped wires (-) to the factory harness leading to

the factory ampliers. If there are common audio return wires (-) used in the vehicle for either the front and rear channels then connect the negative outputs of

the OEM-2 to them. If there is only one audio return wire for all four channels connect all the black-striped wires to it. Connecting the constant power (yellow),

switched power (red), ground (black), antenna trigger (blue), illumination (orange), and amplier turn on (blue/white) through the OEM-2 simplies wiring to the

vehicle. The output level controls can be adjusted with a small screwdriver.

1) Replace the factory premium radio with an after market radio/deck and retain the use of the factory ampliers and speakers

OEM-2

Pa cific Accessory Corporation - S anta Ana, CA 92705

102.7 FM

wht & wht/blk

gray & gray/blk

grn & grn/blk

vio & vio/blk

(-)

(+)

(-)

(+)

(-)

(+)

(-)

(+)

Aftermarket stereo

connect blu/wht to new stereo's remote wire

Factory Amplifier

blu/wht amplifier remote turn on

wht & wht/blk

gray & gray/blk

grn & grn/blk

vio & vio/blk

plug removed from factory stereo

Input

Output

Pacic Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705

techsupport@pac-audio.com • Voice: (800) 854-3133 • Fax: (800) 832-9722 • www.pac-audio.com Page 2

The factory radio speaker outputs are connected to the OEM-2 inputs and the new amplier is connected to the output side of the OEM-2, using the four RCA

jacks and extension cables. Referring to the wire color chart, connect the factory radio speaker (+) outputs to the solid color wires and the (-) outputs to the

black-striped wires. Example, LF speaker outputs of the factory radio connect to the white wire (+) and white/black (-). Continue for the remaining channels. The

OEM-2 provides an amplier turn on signal. To use, connect the blue/white wire on the OEM-2 input side to one of the positive speaker wires or to any source

that provides 5 volts DC or greater. The blue/white wire on the output side will provide 12 volts to turn on the new amplier. Connect the red (+) and black (-) wires

on the input side to switched vehicle power and ground. Adjust the output level controls as needed using a small screwdriver.

2) Adding an aftermarket amplier to a standard factory radio that does not have factory ampliers

OEM-2

Paci ic cc a i a a af A essory Corpor t on - S nt An , CA 92705

wh te wht/blki &

g a & g ar y r y/blk

g & green rn/blk

v olet v o/blki & i

(-)

(+)

(-)

(+)

(-)

(+)

(-)

(+)

102.7 FM

F tory stereoac

New Ampl f eri i

(-)

(+)

(-)

(+)

New subwoofers

Input

Output

blu/wht

Conne t blu/wht w re to nyc i a

spe ker w re output of f torya i ac

r d o (+ or -) for remote turn ona i

for new mpl f er.a i i blu/wht 12 volt remote output

RCA out to

new mpl f era i i

Referring to the wire color chart above, connect the audio output leads of the factory stereo to the input of the OEM-2, using the red striped wires as the positive

input and black-striped as negative. Most premium systems use a low -level signal from the stereo to the factory ampliers, therefore use the low level input of

the OEM-2. Some factory-amplied systems use common audio returns and grounded shields like for instance, GM/Delco Bose vehicles. Do not cut the shield

wire or attempt to use it as an audio signal wire. Determine if your system has two common audio return wires, one for the front channels and a second for the

rear channels. If so, connect the negative input wires (black-stripe) for the front channels of the OEM-2 to the common audio return wire in the vehicle for the

front channels. Do the same for the rear channels. If the vehicle has only one audio return wire for all channels connect all of the black stripped wires to it. The

output level controls can be adjusted with a small screwdriver. Connect the red (+) and black (-) wires on the input side to switched vehicle power and ground.

OEM-2

Paci ic cc a i a a af A essory Corpor t on - S nt An , CA 92705

wht/red wht/blk&

g a & g ar y/red r y/blk

g & grn/red rn/blk

v o/red v o/blki & i

(-)

(+)

(-)

(+)

(-)

(+)

(-)

(+)

102.7 F M

F tory stereoac

New Ampl f eri i

blu/wht 12 volt remote output

RCA out to

new mpl f era i i

(-)

(+)

(-)

(+)

New subwoofers

F tory mpl f erac a i i

Input

Output

blu/wht

Conne t blu/wht w re toc i

f tory mpl f er remote turnac a i i

on. Ex mple: s ome Fordsa

h ve 5 volt remote turn on.a a

3) Adding after market ampliers to a factory premium amplied system (Bose, JBL, etc.)

Referring to the wire color chart, connect the new stereo positive speaker outputs to the red striped wire on the input side of the OEM-2. Connect the negative

speaker outputs to the black-striped wires of the OEM-2. On the output side of the OEM-2 connect the red-striped wires to the vehicle positive speaker wiring.

The black striped wires on the output are not used. The negative side of each speaker is either common to each other on one wire or two in the factory plug or

already grounded to the chassis. However it may be, make sure that they are grounded to the vehicle chassis. The output level control on the OEM-2 will not

function in this conguration.

OEM-2