PAC NU-GM3 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor PAC NU-GM3 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
Pacic Accessory Corporation - Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
03-27-10
NU-GM3
GM LAN 29bit
Navigation Unlock
Integration Interface for
Vehicles with 44-Pin Connector
Installation: Disconnect the black 44-pin main harness from the back of
the radio (see g. A) Plug the male connector on the NU-GM3 harness into the
44-pin port on the back of the radio. Connect the factory 44-pin harness into
the female connector on the NU-GM3 harness.Plug the Black micro-t 24-pin
connector on the NU-GM3 harness into the NU-GM3.
Locate the vehicles VSS wire in pin 20 of the gray 20-pin plug on the back of
the radio (see g. A & B). PLEASE NOTE: The color of the wire in pin 20
will dier depending on the vehicle you are working on. This wire will need
to be cut then connected as follows: The green/black wire from the NU-GM3
should be connected to the radio/plug side of the VSS wire and the green/white
wire from the NU-GM3 should be connected to the vehicle side of the VSS
wire.
If you wish to enable the reverse camera unlock feature you must power up
the factory reverse camera. To do this a wire must be ran from the NU-GM3’s
red camera turn on wire to the factory power wire for the reverse camera. The
location of this wire will vary depending upon which vehicle you are installing
the NU-GM3 into. Please see the next page for the different locations.
Please Note: If the customer does not wish to use the Reverse Camera unlock
feature you do not have to locate and connect this wire. However if the lock
button is pressed when the NU-GM3 is active the screen will switch to reverse
camera mode.
The NU-GM3 is a Navigation Unlock integration interface that allows the factory navigation features of
your GM radio or the reverse camera to be used by the passenger at anytime.
To Vehicle
See Chart Below
For Connections
To Factory Radio
NUGM3 Harness
Connection Diagram
Wire Color Function Connect To
Red Reverse Camera Turn On Output (+) Reverse Camera Trigger in Tailgate
Green/White VSS Input Vehicle side of wire in pin 20 of the gray 20-pin plug behind radio
Green/Black VSS Output Radio side of wire in pin 20 of the gray 20-pin plug behind radio
Installation
Page 1
Main 44-pin Plug Gray 20-pin Plug
Pin 20
Fig A Fig B
Pacic Accessory Corporation - Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
03-27-10 Page 2
Reverse Camera Wire Connection
1. You will need to locate the reverse camera harness. If you are installing the NU-GM3 into a Cadillac SRX, Chevrolet Equinox or GMC Terrain,
the reverse camera harness is in the tailgate (Fig A). If you are installing the NU-GM3 into a Buick LaCrosse, the reverse camera harness is in
the trunk lid (Fig- B).
2. Now you will need to locate the reverse camera wire. In the SRX, Equinox & Terrain the reverse camera wire is the lt. green wire in pin 6 of the
16 pin plug (Fig- C). In the LaCrosse the reverse camera wire is the lt. green wire in pin 8 of the 10-pin plug (Fig- D). Please verify that this wire
shows 12v (+) when the vehicle is shifted into reverse.
3. Connect the red camera turn on wire from the NU-GM3 to the lt. green wire using a diode (Fig E). The diode is needed to prevent the reverse
lights from coming on when the reverse camera is activated.
4. Verify that the reverse lights do not come on when the reverse camera unlock feature is being used.
Fig A Fig B
Reverse
Camera
Red Camera Activation Wire
Lt Green Camera Wire
Connect Diode
Here
Connect Red Wire
From NU-GM3 Here
Fig E
Reverse Camera Harness
Light Green Wire Pin 6
Fig C Fig D
Reverse Camera Harness
Light Green Wire Pin 8
Pacic Accessory Corporation - Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
03-27-10
Installation/Compatibility Notes
1. The NU-GM3 text will not be displayed when the OnStar Turn-by-Turn Navigation is being used.
2. When you rst install the interface you must move the shifter to drive and back to park before the reverse camera override will work
DISCLAIMER: Under no circumstances shall the manufacture or the distributors of the NU-GM3 be held liable for claims of any loss or damage,
consequential, direct or indirect, arising from the sale, installation, or use of the NU-GM3. The manufacture and its distributors will not, nor will they
authorize any representative or any other individual, to assume obligation or liability in relation to the NU-GM3 other than its replacement.
AGREEMENT: End user agrees to use this product in compliance with the instructions and terms of use above and with all State and Federal
laws. PAC provides instructions and safety warnings with respect to this product and disclaims all liability for any use not in conformity with those
instructions or other misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This
product is intended for o-road use and passenger use only.
Pre 2012 Cadillac SRX Controls
Press & hold to
enable/disable
Navigation Unlock
1. Press & Hold the
Source Button
2. Navigation Screen
Displays: Confirm
Safe Passenger Use
3. Press the Source
Button Again to
Confirm
4. Repeat Step 1
to De-Activate
Chevy Equinox, GMC Terrain
Buick LaCrosse & 2012+ Cadillac SRX Controls
1. Press & Hold the
Mute Button
2. Navigation Screen
Displays: Confirm
Safe Passenger Use
3. Press the Mute
Button Again to
Confirm
4. Repeat Step 1
to De-Activate
Press & hold to
enable/disable
Navigation Unlock
SRC
Activating the Navigation Unlock
In the SRX, press and hold the “Source” button on the steering wheel controls (SWC) for two seconds to activate the NU-GM3. In the
Equinox, Terrain & LaCrosse, press and hold the “Mute” button on the steering wheel controls (SWC) for two seconds to activate the NU-
GM3. You will hear one chime and the navigation screen will display “Conrm Safe Passenger Use”. Press the “Source” or “Mute” button
on the SWC again to acknowledge “safe use”, agreeing that use will be performed only by the passenger whenever the
vehicle is in motion, and activate the NU-GM3. To de-activate the NU-GM3 simply press and hold the “Source” or “Mute” button on
the SWC until three chimes are heard.
Activating the Reverse Camera Unlock
Activate the navigation unlock using the SWC. Press the “Lock” button on the radio or center console, the rearview camera image will now
display on the navigation screen. Press the “Lock” button again to de-activate the reverse camera
WARNING: In order to avoid distraction, which could lead to an accident, the driver should never utilize systems unlocked
by the NU-GM3 when the vehicle is in motion. Even when operated by the passenger, the vehicle driver should maintain their
attention on the road at all times.
Operation
Page 3


Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: NU-GM3

Heb je hulp nodig?

Als je hulp nodig hebt met PAC NU-GM3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd PAC

PAC

PAC RP4-GM31 Handleiding

31 Augustus 2024
PAC

PAC NU-GM51 Handleiding

28 Augustus 2024
PAC

PAC NAV-1129 Handleiding

28 Augustus 2024
PAC

PAC LP7-2R Handleiding

28 Augustus 2024
PAC

PAC LP7-4 Handleiding

28 Augustus 2024
PAC

PAC GMK367B Handleiding

28 Augustus 2024
PAC

PAC CP1-FRD1 Handleiding

28 Augustus 2024
PAC

PAC C2A-CHY5 Handleiding

28 Augustus 2024
PAC

PAC NU-GM3 Handleiding

28 Augustus 2024
PAC

PAC CP1-TSL1 Handleiding

28 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd