PAC IR-X Handleiding

PAC Niet gecategoriseerd IR-X

Lees hieronder de đź“– handleiding in het Nederlandse voor PAC IR-X (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/1
Paciîšżc Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com
Paciîšżc Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com
IR-X Infrared Remote Repeater Installation Instructions 8-15-03
Control remote mounted / hidden video players and stereos using the units IR remote*.
* note: The IR remote being used must use a 40kHz or 56kHz carrier
frequency. Consult with equipment manufacture to determine the carrier
frequency. Check website for known units that do not work.
Special Features:
• Easy 2 wire hook up
• Extra long plug-in wire for remote IR
LED
• Red LED ashes for conrmation of
wireless remote operation (red LED
will be dim when ashing)
• Small and easy to mount
• 40kHz and 56kHz operation
Black receiver
(Round dimple must
face wireless remote)
Clear emitter on 1/8" plug
(round dimple must face device)
1. Connect Red wire to 12 volts accessory (switched power)
2. Connect Black wire is vehicle ground (negative)
3. Mount IR receiver (on the end of the short black wire) with the
round dome side facing out where it is in range / sight of the
remote control.
4. Mount IR LED (on the end of black wire with 1/8” plug) in front
of the unit/s to be controlled. The IR LED is directional, so
make sure the dimple on the side of the clear IR LED is facing
the unit being controlled. It can be taped to the front of the
unit or mounted in a location that can be seen by two or more
units to be controlled.
5. By leaving the brown wire of the IR-X disconnected and
insulated, it will transmit at a 40kHz IR signal, which is used
for most applications.
-or-
When the brown wire is connected to vehicle ground
(negative) the IR-X will transmit at a 56kHz IR signal which
is used in fewer applications. Ground the brown wire if only
the control response is slower than normal or is intermittent.
Installation Instructions
IR-X Infrared Remote Repeater Installation Instructions 8-15-03
Control remote mounted / hidden video players and stereos using the units IR remote*.
* note: The IR remote being used must use a 40kHz or 56kHz carrier
frequency. Consult with equipment manufacture to determine the carrier
frequency. Check website for known units that do not work.
Special Features:
• Easy 2 wire hook up
• Extra long plug-in wire for remote IR
LED
• Red LED ashes for conrmation of
wireless remote operation (red LED
will be dim when ashing)
• Small and easy to mount
• 40kHz and 56kHz operation
Black receiver
(Round dimple must
face wireless remote)
Clear emitter on 1/8" plug
(round dimple must face device)
1. Connect Red wire to 12 volts accessory (switched power)
2. Connect Black wire is vehicle ground (negative)
3. Mount IR receiver (on the end of the short black wire) with the
round dome side facing out where it is in range / sight of the
remote control.
4. Mount IR LED (on the end of black wire with 1/8” plug) in front
of the unit/s to be controlled. The IR LED is directional, so
make sure the dimple on the side of the clear IR LED is facing
the unit being controlled. It can be taped to the front of the
unit or mounted in a location that can be seen by two or more
units to be controlled.
5. By leaving the brown wire of the IR-X disconnected and
insulated, it will transmit at a 40kHz IR signal, which is used
for most applications.
-or-
When the brown wire is connected to vehicle ground
(negative) the IR-X will transmit at a 56kHz IR signal which
is used in fewer applications. Ground the brown wire if only
the control response is slower than normal or is intermittent.
Installation Instructions

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: IR-X

Heb je hulp nodig?

Als je hulp nodig hebt met PAC IR-X stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC RP4-GM31 Handleiding

31 Augustus 2024
PAC

PAC NU-GM51 Handleiding

28 Augustus 2024
PAC

PAC NAV-1129 Handleiding

28 Augustus 2024
PAC

PAC LP7-2R Handleiding

28 Augustus 2024
PAC

PAC LP7-4 Handleiding

28 Augustus 2024
PAC

PAC GMK367B Handleiding

28 Augustus 2024
PAC

PAC CP1-FRD1 Handleiding

28 Augustus 2024
PAC

PAC C2A-CHY5 Handleiding

28 Augustus 2024
PAC

PAC NU-GM3 Handleiding

28 Augustus 2024
PAC

PAC CP1-TSL1 Handleiding

28 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024