PAC IGN-3 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor PAC IGN-3 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev. 101118
The IGN-3 phantom ignition module is ideal for use in CAN-Bus vehicles, and vehicles with stop-start technology, commonly
found in push-to-start vehicles, or Hybrid vehicles. It monitors the electrical activity in the vehicle and provides an ignition lead
that provides voltage as soon as the engine is running (accessory function for CAN-Bus vehicles).
Introduction and Features
Wiring Information
Operation
Troubleshooting
LED is not flashing - Using a Multimeter, check that there is 12 volts present on the Red wire, and a solid ground connection
on the Black wire.
Aftermarket accessory is shutting off while vehicle is running - If your installation requires a longer accessory output,
cut the Brown Loop wire to increase the power-off delay to 140 seconds, to ensure continued operation of aftermarket products.
IGN-3 Power-off Delay Function:
In many late-model vehicles, the alternator can shut off while the vehicle is driving, to maximize fuel economy. Other new
vehicles will shut the engine down when stopped at a red light, and start it up again when the accelerator is pressed.
The IGN-3 is designed with 2 different power-off delay settings, that can be used to compensate for these vehicle functions.
A short delay of 10 seconds, or a long delay of 140 seconds are available, to provide consistent power to your aftermarket
accessories, to ensure their proper operation during these partial power-down scenarios.
In the default setting (Brown loop wire uncut), after the vehicle’s engine is turned off, the Blue wire output will remain
active for 10 seconds. If the Brown Loop wire is cut, the Blue wire will remain active for 140 seconds after engine shutdown.
LED information:
If the LED is flashing once every three seconds, the module is in standby mode, ready to sense the vehicle’s engine start.
If the LED is illuminated solid. The (Blue) phantom ignition output wire is active.
1. Black - Connect to chassis ground
2. Blue - 12 volt output (once triggered) 2 amps max.
3. Red - Connect to Constant Power
4. Brown Loop - Uncut loop = 10 second delay
IGN-3 is designed to provide up to 2 amps of output.
For installations demanding more current, the use of an external relay is required.
IGN-3 Power-on Function:
The IGN-3 module monitors the voltage level and noise on the constant power circuit to sense the starting of the engine and
running of the alternator, and immediately turns on the phantom ignition output (Blue wire).
- Cut loop = 140 second delay
IGN-3 Phantom Ignition Module for CAN-Bus Vehicles
and Vehicles with Stop-Start Technology
IGN-3
Phantom Ignition Module for
CAN-Bus Vehicles and Vehicles
with Stop-Start Technology
Made in China


Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: IGN-3

Heb je hulp nodig?

Als je hulp nodig hebt met PAC IGN-3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd PAC

PAC

PAC RP4-GM31 Handleiding

31 Augustus 2024
PAC

PAC NU-GM51 Handleiding

28 Augustus 2024
PAC

PAC NAV-1129 Handleiding

28 Augustus 2024
PAC

PAC LP7-2R Handleiding

28 Augustus 2024
PAC

PAC LP7-4 Handleiding

28 Augustus 2024
PAC

PAC GMK367B Handleiding

28 Augustus 2024
PAC

PAC CP1-FRD1 Handleiding

28 Augustus 2024
PAC

PAC C2A-CHY5 Handleiding

28 Augustus 2024
PAC

PAC NU-GM3 Handleiding

28 Augustus 2024
PAC

PAC CP1-TSL1 Handleiding

28 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd