PAC C2R-CHY4 Handleiding

PAC Niet gecategoriseerd C2R-CHY4

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC C2R-CHY4 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 177 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
Paciî‚¿c Accessory Corporation - Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
7-19-10
J1850
Class 2
VPW
Class 2
J1850
100011101111001001101100
111010000110110111001100
EOD
CRC
100011101111001001101100
111010000110110111001100
Class 2
Class 2
J1850
Radio Replacement Interface
with Nav Outputs for all Chrysler
Dodge / Jeep CANbus Vehicles With
or Without Premium Audio Systems
C2R-CHY4
1. Only one of the two provided radio harnesses will be used. Remove the factory
installed radio to determine the correct harness for your particular vehicle.
2. Vehicles without a factory amplier: Connect the aftermarket radio’s front and
rear speaker wires to the 22 pin plug.
3. Vehicles with a factory ampliî‚¿er: The factory ampliî‚¿er only accepts two audio
channels (left and right). The amplier’s fading is controlled by data communication
from the factory radio. The aftermarket radio does not have the ability to control the
amplier’s fader. Connect the front outputs of the aftermarket radio to the rear inputs of the 22 pin radio connector. This will
allow navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs of the aftermarket radio are not used.
4. The accessory output wire is located on the 11 pin CAN INTERFACE harness - connect this wire to the radio’s accessory wire. The
accessory wire supplies +12v, 1 amp max when key is in the accessory or ignition position (î‚¿g. 1: If more current is needed).
5. 11 pin plug (to CAN INTERFACE):
Blue/White - Connect this wire to the radio’s amplifier remote output. Connect this wire with or without OEM amp present!1.
White/Green - SWC output.2.
Green - Connect this wire to the radio’s reverse input wire only.3.
Orange/White - Connect this wire to the radio’s Illumination input wire only.4.
Violet/White - Connect this wire to the radio’s VSS input wire only.5.
Red/White - Connect this wire to the radio’s parking brake input wire only.6.
Note: Do not connect these wires to any circuit other than the radio’s wire harness.
6. 11 pin plug (to SWC INTERFACE):
This is a quick connection to a radio speciî‚¿c SWC interface. No additional
connections are necessary other than radio control connections. Plug the radio
speciî‚¿c SWC interface in to this connector and program the radio speciî‚¿c SWC
interface for version 2. Do not cut the loops. Refer to the SWC interface instruction
manual for the radio speciî‚¿c control function programming order.
7. Refer to the aftermarket radio’s instruction manual for testing VSS, Reverse, Parking Brake and Illumination outputs. For the most
current and Up-to-Date application guide please visit www.pac-audio.com
Fig. 1
(using a SPDT relay)
85 86
30
87
87a
Ground
High Current 12v
(Fused)
12v Acc.
From
Interface
New High
Current Output
Diode 1N4005
or equivelant
9
1
23456
78
1011
Accessory Output
+12volts 1amp max.
Ch
9 1
9
1
23456
78
1011
9 1
SWC Interface.
Program for Version 2
Radio Specific Steering
Wheel Control Interface
(Sold Separately)
Program SWC
Interface for Version 2.
CAN INTERFACE
Navigation outputs and
Amplifier Remote Input
See Chart for wire color
descriptions.
Radio Connections. See aside
Chart for color description.
Yellow Battery +12v
Black Ground
Blue Antenna On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
(Read the Installation Notes before making
connections to the provided radio harness)
CAN Interface Connection Chart:
Red Acc. Output (1 amp)
Red / White P.B. Output (-)
Purple / White VSS Output (Pulse)
Orange / White Illum. Output (+)
Green Reverse Output (+)
White / Green SWC Output
Blue / White Amp Turn On Input
Installation Notes
Radio Connection Chart
Paciî‚¿c Accessory Corporation - Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
7-19-10
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the C2R-CHY4 be held liable for consequential damages sustained in
connection with the C2R-CHY4. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume
obligation or liability in relation to the C2R-CHY4 other than its replacement.
Using the VES & Reverse Camera (if equipped)
Vehicles equipped with a DVD player built into the rear screen assembly:
The C2R-CHY4 will allow the VES DVD player and rear screen to function as if the factory radio were present. A/V will be passed
from the factory DVD player to the rear screen and audio can be heard through the headphones. A/V cannot be passed from the
factory DVD player to the aftermarket head unit.
Vehicles equipped with a stand alone VES DVD Player:
The C2R-CHY4 will allow the VES DVD player and rear screen(s) to function as if the factory radio were present. A/V will be
passed from the factory DVD player to the rear screen(s) and audio can be heard through the headphones. A/V can also be fed
from the VES DVD player into an aftermarket head unit (head unit must support A/V in) with the use of the CHYRVD.
Vehicles not equipped with a VES DVD Player (rear screen(s) only):
In this application the CHYRVD must be used in order to feed A/V into the factory screen(s) from an aftermarket head unit (head
unit must support A/V out). With the CHYRVD, A/V will be passed from the aftermarket head unit to the rear screen(s) and audio
can be heard through the headphones. If you wish to retain the Auxiliary inputs on the rear of the console you must disconnect the
factory wires from the auxiliary input then connect and run your own RCAs into the aftermarket head unit.
Vehicles equipped with a Reverse Camera:
In order to retain the factory reverse camera the CHYRVD must be used to feed video into the aftermarket head unit (head unit
must support reverse camera input).

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: C2R-CHY4

Heb je hulp nodig?

Als je hulp nodig hebt met PAC C2R-CHY4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC RP4-GM31 Handleiding

31 Augustus 2024
PAC

PAC NU-GM51 Handleiding

28 Augustus 2024
PAC

PAC NAV-1129 Handleiding

28 Augustus 2024
PAC

PAC LP7-2R Handleiding

28 Augustus 2024
PAC

PAC LP7-4 Handleiding

28 Augustus 2024
PAC

PAC GMK367B Handleiding

28 Augustus 2024
PAC

PAC CP1-FRD1 Handleiding

28 Augustus 2024
PAC

PAC C2A-CHY5 Handleiding

28 Augustus 2024
PAC

PAC NU-GM3 Handleiding

28 Augustus 2024
PAC

PAC CP1-TSL1 Handleiding

28 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024