PAC ANC-CH01 Handleiding

PAC Niet gecategoriseerd ANC-CH01

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC ANC-CH01 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 172 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/1
ANC Module Bypass Harness for Select
Chrysler, Dodge, Jeep, RAM Vehicles
C
Page 1
Copyright © 2019. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
ANC-CH01
Rev: V3
Date: 071819
Introduction and Features
The ANC-CH01 harness bypasses the Active Noise Cancellation (ANC) module in select Chrysler, Dodge, Jeep and
RAM non-amplied audio systems while maintaining communication between the vehicle’s CAN bus network and the
module. Aftermarket ampliers can easily be added with no need to cut or modify a vehicle’s original wiring.
Installation Notes
1. WARNING: Passing the speaker signal from aftermarket amplier through the ANC module will cause DAMAGE!
2. The ANC-CH01 is only compatible with non-amplied vehicles that have the ANC system. To determine compatibility, some
key factors to look for would be the inclusion of an active center channel and / or subwoofer. If the audio system includes either
or both, the ANC-CH01 is not compatible because the system is factory amplied.
3. The ANC-CH01 can be used to provide speaker wire connections for all 4 speakers, eliminating the need to cut into the factory
harness (see “Installation Steps” for info.).
4. When using the ANC-CH01 harness to connect speaker wire outputs from an aftermarket amplier, it is always best to use a
tone generator (PAC part number TL-PTG2) to verify that the tables in this manual match the wiring in your specic vehicle.
1. Locate the vehicle’s ANC module and disconnect the 16-pin and 22-pin connectors.
a. RAM Truck: The ANC module is under the driver’s seat
b. Jeep Cherokee: The ANC module is above the glove box
c. Chrysler Pacica: The ANC module is to the right of the glove box
2. Connect the ANC-CH01 harness to the connectors that were disconnected in the previous step.
3. Connect the male 22-pin connector from the ANC-CH01 to the ANC module.
4. When connecting the ANC-CH01 to the outputs of an aftermarket amplier, use the wiring information (provided in the chart
below) to determine which will be used.
a. Cut the wires in the ANC-CH01 that will be used for connection to the aftermarket amplier speaker outputs. The
wiring overview (provided in the chart below) shows the approximate location of where the wires should be cut.
b. Leave any speaker wires that are going to be powered from the radio (rather than from an aftermarket amplier),
intact.
c. Connect the outputs of the aftermarket amplier to the appropriate wires in the ANC-CH01 harness that go to 16-pin
side of the cut harness.
d. Insulate the cut wires that lead to the 22-pin side of the harness as they will not be used.
Installation Steps
PinNumber WireColor Description Label
1
9
2
10
3 White/Black LeftFront‐
11 White LeftFront+
4 Gray/Black RightFront‐
12 Gray RightFront+
5 Green/Black LeftRear‐
13 Green LeftRear+
6 Purple/Black RightRear‐
14 Purple RightRear+
7
15
8
16
N/A
N/A
LFSpeaker
RFSpeaker
LRSpeaker
RRSpeaker
Wiring Overview
*Illustration is for reference only.
Your harness will have more wires*
22-Pin to ANC Module
22-Pin to Harness from
ANC Module
16-Pin to Harness from
ANC Module
Speaker Wires from
Radio
Speaker Wires To
Speakers
Wires can be cut here to allow for
connection to an aftermarket amplifier.
See “Installation Steps” (4a - 4d) for
additional info.

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: ANC-CH01

Heb je hulp nodig?

Als je hulp nodig hebt met PAC ANC-CH01 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC RP4-GM31 Handleiding

31 Augustus 2024
PAC

PAC NU-GM51 Handleiding

28 Augustus 2024
PAC

PAC NAV-1129 Handleiding

28 Augustus 2024
PAC

PAC LP7-2R Handleiding

28 Augustus 2024
PAC

PAC LP7-4 Handleiding

28 Augustus 2024
PAC

PAC GMK367B Handleiding

28 Augustus 2024
PAC

PAC CP1-FRD1 Handleiding

28 Augustus 2024
PAC

PAC C2A-CHY5 Handleiding

28 Augustus 2024
PAC

PAC NU-GM3 Handleiding

28 Augustus 2024
PAC

PAC CP1-TSL1 Handleiding

28 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024