PAC AAI-GM9 Handleiding

PAC Niet gecategoriseerd AAI-GM9

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC AAI-GM9 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/1
Paciîš¿c Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com
11-16-05
AAI-GM9
Auxiliary Audio Input for GM Vehicles
The AAI-GM9 allows direct interface of any preamp level audio source to a GM factory radio
with a slave unit, eliminating the need for sound degrading solutions like an FM modulator.
The AAI-GM9 interface inputs sources from units such as a DVD, VCP, MP3, Satellite Radio
or PlayStation.
• Lower cost and higher quality sound than a FM modulator.
• Perfect for SUV’s like Escalade, Tahoe, Suburban, Denali and Yukon.
• Comes with a three position switch which allows you to switch between two auxiliary inputs and the
factory slave unit.
• High quality audio isolation IC eliminates engine noise.
• Internal CMOS electronic switching for long term reliability.
• Completely plug & play. Requires no external wiring.
• Seamless operation with OnStar® equipped vehicles.
Requirements: For 1995-2002 vehicles* the Sedan or SUV factory headunit must have a
working slave unit which uses the GM 9 pin connector. Slave unit examples are: factory/
aftermarket CD changer, separate factory cassette player or single CD player.
Installation
1. Remove factory 9 pin connector from radio and insert the AAI-GM9 male plug in it’s place.
Plug factory 9 pin connector into the AAI-GM9 female connector as shown in Fig.1 below.
2. Plug RCA cables from îš¿rst audio source into Aux1 input of AAI-GM9. If there is a second
audio source, plug RCA into Aux2 input.
3. Mount the toggle switch in a suitable location.
AAI-GM9
GM Auxiliary Audio Input
Aux 1
Input
Aux 2
Input
Pacific Accessory Corporation, Santa Ana, CA 91792
Left
Left
Right
Right
Aux1/Aux2
Switch
Insert these two plugs in between the
factory headunit and factory 9 pin plug
DELCO ELECTRO NICS
123
4 5 6
SEEK
TAPEAUX
AM FM
FADE BAL BASS TREB
EJECT
PWR VOL
TUNE
RECALL
Factory wire harness
to factory slave unit
DVD player
or Satellite Radio VCP player
or Playstation
Fig. 1
Brown wire
Testing
1. Turn radio on and select Tape or CD changer source. Note: a cassette or CD must be
inserted into the slave unit and playing.
2. With the switch in the middle position you should hear the Tape or CD audio.
3. When you ip the switch left or right of the middle position, you should hear Aux1 or Aux2
audio.
4. Vehicles with OnStar®: When activating OnStar® with the AAI-GM9 switch to either
Aux1 or Aux2, the auxiliary audio will be automatically overridden so OnStar® audio can
be heard. When turning off OnStar®, Aux1 or Aux2 audio will resume.
5. Connect the brown wire to chassis ground only if the portable player Portable Players:
and other audio source is not using the vehicle’s battery as a power supply.
OnStar® Ready!
Most overhead video consoles have a +12 volt
trigger output when the video system is turned
on. Use a SPDT relay as shown and connect
pin 30 of relay to the AAI-GM9 switch’s red wire.
Connect pin 87 to the AAI-GM9 switch’s shield
wire. Use Aux2 as the external audio source
input and leave switch in the middle position.
This automatic feature will only work on Aux2
input and not Aux1.
30
85
86
87
87a
To overhead
+12v trigger output
Tap into AAI-GM9
switch's red wire
Tap into AAI-GM9
switch's shield(bare) wire
Terminal side of switch
Red
White
Shield
Using external video source to automatically trigger the AAI-GM9 for Aux2
Description
Bulletin
1999-2000 Escalade, Denali and 1999-2002 Pontiac Grand Prix
1999-2000 Cadillac Escalade, GMC Denali and 1999-2002 Pontiac Grand Prix, see bulletin.
To retain the automatic switching when OnStar® is activated, relocating the Lt..
green wire from the AAI-GM9 to the factory
21 pin radio connector will be necessary.
1. Cut the Lt.. green wire coming from the
AAI-GM9 at white plug leaving the wire in be-
tween the two connectors intact. Tap the wire
into pin #15 dark green wire of the factory 21
pin connector shown to the right.
11 20
1 10
15
Factory Plug Shown from
pin side not wire side

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: AAI-GM9

Heb je hulp nodig?

Als je hulp nodig hebt met PAC AAI-GM9 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC RP4-GM31 Handleiding

31 Augustus 2024
PAC

PAC NU-GM51 Handleiding

28 Augustus 2024
PAC

PAC NAV-1129 Handleiding

28 Augustus 2024
PAC

PAC LP7-2R Handleiding

28 Augustus 2024
PAC

PAC LP7-4 Handleiding

28 Augustus 2024
PAC

PAC GMK367B Handleiding

28 Augustus 2024
PAC

PAC CP1-FRD1 Handleiding

28 Augustus 2024
PAC

PAC C2A-CHY5 Handleiding

28 Augustus 2024
PAC

PAC NU-GM3 Handleiding

28 Augustus 2024
PAC

PAC CP1-TSL1 Handleiding

28 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024