Ozito PXHDIS-240U Handleiding

Ozito Compressor PXHDIS-240U

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PXHDIS-240U (3 pagina's) in de categorie Compressor. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

SPECIFICATIONS

Input: 18V (DC) or 220-240V ~ 50Hz (AC)

No Load Speed: 15,000/min

Max Pressure: 11 bar (160PSI)

Air Hose Length: 71cm (high pressure)

31cm (high volume)

Protection Class II

Weight (tool only): 2.2kg

HYBRID

INFLATOR /

DEFLATOR

ORIGINAL INSTRUCTIONS

STANDARD EQUIPMENT

Hybrid Inﬂator /

Deﬂator

High Volume Air Hose

3 x Inﬂation Adapters

SPARE PARTS

GENERAL POWER TOOL SAFETY WARNINGS

BATTERY PROTECTION SYSTEM

INFLATOR / DEFLATOR SAFETY WARNINGS

PXHDIS-240U

Art.-No.: 30.002.87 I.-No.: 11017

0318

MODE

The tool is equipped with the battery protection system, which helps to ensure a long service

life.

The output power automatically cuts off during operation when the tool and/or battery are

placed under the following situations:

• When the tool is overloaded:

If this occurs, release the trigger switch and remove causes of overload, then pull the

switch trigger again to restart.

• When the remaining battery capacity becomes low:

Recharge the battery pack.

Note: The battery protection system does not in any way damage the tool.

Note: The indicated capacity may be lower than the actual level during use or immediately

after using the tool.

WARNING! Safety information for the compressor Danger! The following basic

safety actions must be taken when using this compressor in order to protect the user from

electric shocks and the risk of injury and ﬁre. Read and follow these instructions before using the

equipment.

• Check the ambient conditions

Do not expose the compressor to rain. Never use the compressor in damp or wet locations. There is a risk of electric shock!

Provide good lighting. Do not use the compressor near ammable liquids or gases. There is a risk of explosion!

• Protect yourself against electric shocks

Avoid bodily contact with earthed parts, e.g.pipes, radiators, cookers and refrigerators.

• Keep children away!

Do not allow other persons to touch the compressor or cable, keep them away from your work area.

• Do not use the cable for purposes other than that for which it is designed

Do not carry the compressor by its cable and do not use the cable to pull the plug out of the socket. Protect the cable from

heat, oil and sharp edges. The cable/plug could become damaged.

• Take care of your compressor

Keep your compressor clean in order to work well and safely. Follow the maintenance instructions. Check the power plug

and cable on a regular basis and have them replaced by an authorized specialist if they are damaged. Check the extension

cable regularly and replace it if damaged.

• Avoid unintentional starting

Make sure that the switch is turned off when connecting to the power supply.

• Check your compressor for damage

Before using the compressor again, carefully check the safety devices and any slightly damaged parts to ensure that they

are in good working order. Check that the moving parts are working correctly, that they do not jam, and that no parts are

damaged. Make sure that all parts are tted correctly to ensure that the equipment remains safe to use. Unless otherwise

stated in the operating instructions, damaged guards and parts have to be repaired or replaced by a customer service

workshop. Damaged switches have to be replaced by a customer service workshop. Never use an electric power tool with a

switch that cannot be turned on and off.

• Leave all repairs to a qualiﬁed electrician

Repairs must be left strictly to qualied electricians or the user might suffer an accident.

• Noise

Wear ear muffs when you use the compressor.

• Replacing the power cable

To prevent hazards, leave the replacement of damaged power cables strictly to the manufacturer or a qualied electrician.

There is a risk of electric shock!

• Inﬂating tires

Directly after inating tires, check the pressure with a suitable pressure gauge, for example at your lling station.

• Place of installation

Set up the compressor on an even surface.

Safety instructions for working with compressed air and blow-out pistols

• The air, which is sucked in by the compressor, must be kept free of impurities that could cause res or explosions in the

compressor pump.

• Wear safety goggles. Foreign bodies or blown off parts can easily cause injuries.

• Do not blow at people and do not clean clothes while being worn. Risk of injury!

Keep this safety information in a safe place.

TROUBLESHOOTING

• Keep air intake clean and air vents free of debris to avoid overheating the motor.

• Do not use cleaning agents to clean the plastic parts of the tool.

A mild detergent on a damp cloth is recommended. Water must never come into contact with

the tool.

• If the inator vibrates abnormally, stop motor immediately. Abnormal vibration usually indicates

a mechanical problem continued operation could lead to injury or damage.

WARNING! ENSURE THE TOOL HAS BEEN SWITCHED

OFF AND THE POWER SUPPLY IS DISCONNECTED

PRIOR TO ANY MAINTENANCE.

Problem Cause Remedy

Inator is not

starting

Battery is low in charge Charge battery

Battery or power cord not

connected properly

Ensure battery is inserted correctly or the

power cord is connected

Incorrect operating mode

selected

If a battery is connected, ensure the operating

switch is in the DC mode.

If the power cord is connected, ensure the

operating switch is in the AC mode.

Inator is not

operating at

full capacity

Possible clogging Ensure the air inlet is not blocked when

inating a high volume item.

Ensure the air outlet is not blocked when

deating a high volume item.

Loose hose of adaptor Ensure the hose or ination adaptor is tted

securely

Motor stops

while inating

Battery has no power Charge battery

High pressure item has

reached preset pressure.

The inator will automatically shut-off when

the high pressure item reaches the preset

pressure.

The digital

display is not

working

Power not connected

properly

Ensure the power supply is connected and

the operating mode switch is in the correct

position

Inating or Deating a

high volume item

The digital display will only display the

current pressure when inating a high

pressure item. When inating a high volume

item the display will show 0.00

Note: Ozito Industries will not be responsible for any damage or injuries caused by the repair of the

inator by an unauthorised person or by mishandling of the inator. This tool is designed for DIY use

- use in commercial or industrial environments will void the warranty.

MAINTENANCE

WARRANTY

OZITO UK Champion’s Business Park, Unit 10, 1st Floor, Arrowe Brook Road, Upton, Wirral, Merseyside, CH49 0AB

All of our products undergo strict quality checks to ensure that they reach you in perfect

condition. In the unlikely event that your device develops a fault, please contact our service

department at the address shown on this guarantee card. You can also contact us by

telephone using the customer service number shown. Please note the following terms under

which guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the manufacturer

mentioned below promises to buyers of its new products in addition to their statutory

guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or manufacturing faults on

a product which you have bought from the manufacturer mentioned below are limited to

either the rectication of said defects on the product or the replacement of the product,

whichever we prefer.

Please note that our devices are not designed for use in commercial, trade or professional

applications. A guarantee contract will not be created if the device has been used by

commercial, trade or industrial business or has been exposed to similar stresses during the

guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly instructions or due to

incorrect installation, a failure to follow the operating instructions (for example connecting

it to an incorrect mains voltage or current type) or a failure to follow the maintenance and

safety instructions or by exposing the device to abnormal environmental conditions or by

lack of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example overloading the

device or the use or unapproved tools or accessories), ingress of foreign bodies into the

device (such as sand, stones or dust, transport damage), the use of force or damage caused

by external forces (for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural wear or tear or by

normal use of the device.

4. Your Product is guaranteed for a period of 60 months from the original date of purchase

and is intended for DIY (Do It Yourself) use only. Lithium Ion batteries and chargers are

covered by a 12 month warranty. Warranty excludes consumable parts. Guarantee claims

should be submitted before the end of the guarantee period within two weeks of the defect

being noticed. No guarantee claims will be accepted after the end of the guarantee period.

The original guarantee period remains applicable to the device even if repairs are carried

out or parts are replaced. In such cases, the work performed or parts tted will not result

in an extension of the guarantee period, and no new guarantee will become active for the

work performed or parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO

THE PLACE OF PURCHASE WITH YOUR REGISTER RECEIPT.

Please refer to the restrictions of this warranty concerning wearing parts, consumables and

missing parts as set out in the service information in these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

ozito-diy.co.uk

Spare parts can be ordered from the Special Orders Desk at your local

Bunnings Warehouse or Homebase store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: info@ozito-diy.co.uk

DECLARATION OF CONFORMITY

Dong/Product-ManagementWeichselgartner/General-Manager

explains the following conformity according to EU directives and norms for

the following product

Hybrid In ator / De ator PXHDIS-240U (Ozito)

2014/29/EU

2005/32/EC_2009/125/EC

X 2014/35/EU

2006/28/EC

X 2014/30/EU

2014/32/EU

2014/53/EC

2014/68/EU

90/396/EC_2009/142/EC

89/686/EC_96/58/EC

X 2011/65/EU

2006/42/EC

Annex IV

Noti ed Body:

Noti ed Body No.:

Reg. No.:

2000/14/EC_2005/88/EC

Annex V

Annex VI

Noise: measured LWA = dB (A); guaranteed L

WA = dB (A)

P = KW; L/Ø = cm

Noti ed Body:

2012/46/EU

Emission No.:

Standard references: EN 60335-1; EN 62233

EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3

Landau/Isar, den 19.02.2018

First CE: 18 Archive-File/Record: NAPR018292

Art.-No.: 30.002.87 I.-No.: 11017 Alex KurzDocuments registrar:

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

Category Example

Wear parts* Battery

Consumables*

Missing parts

SERVICE INFORMATION

Please note that the following parts of this product are subject to normal or natural

wear and that the following parts are therefore also required for use as consumables.

* Not necessarily included in the scope of delivery!

DANGER! Read all safety regulations and instructions. Any errors made in following the safety

regulations and instructions may result in an electric shock, re and/or serious injury.

Keep all safety regulations and instructions in a safe place for future use. The term “electric tool” used

in the safety instructions refers to electric tools operated from the mains power supply (with a power cable) and to battery operated

electric tools (without a power cable).

1. Workplace safety

a) Keep your work area clean and well illuminated. Untidy or unlit work areas can result in accidents.

b) Do not operate the electric tool in an environment where there is a risk of explosions and

where there are inﬂammable liquids, gases or dust. Electric tools produce sparks which could set the dust or

vapours alight.

c) Keep the electric tool out of the reach of children and other persons. If there is a distraction, you may

lose control of the appliance.

2. Electrical safety

a) The connector plug from this electric tool must ﬁt into the socket. The plug should never be

altered in any way. Never use adapter plugs together with earthed electric tools. Unaltered plugs and

correct sockets reduce the risk of an electric shock.

b) Avoid bodily contact with earthed surfaces such as pipes, heating, ovens and fridges. The risk of

electric shock is increased if your body is earthed.

c) Keep the tool out of the rain and away from moisture. The ingress of water into an electric tool increases the

risk of an electric shock.

d) Do not use the cable to carry the electric tool, to hang it up or to pull it out of the socket.

Keep the cable away from heat, oil, sharp edges and moving parts of the appliance. Damaged or

entangled cables increase the risk of an electric shock.

e) If you are working outdoors with an electric tool, only use extension cables which are designed

speciﬁcally for this purpose. Using specially designed outdoor extension cables, the risk of electric shock is reduced.

f) If operation of the electric tool in a damp environment can not be avoided, use a earth-leakage

circuit-breaker. The earthleakage circuit-breaker reduces the risk of an electric shock.

3. Safety of persons

a) Be careful, watch what you are doing and use an electric tool sensibly. Do not use the tool if

you are tired or under the inﬂuence of drugs, alcohol or medication. A moment of inattention when using the

electric tool can result in serious injuries.

b) Wear personal protection equipment and always wear safety goggles. Wearing personal protection

(such as dust masks, non-slip safety shoes, safety helmet or ear protection, depending upon the type and use of the electric tool)

reduces the risk of injury.

c) up accidentally. Ensure that the electric tool is switched off Make sure that the appliance cannot start

before you connect it to the power supply and/or insert the battery, or pick up or carry the tool.

If your nger is on the switch whilst carrying the electric tool or if you connect the appliance to the mains when it is switched on, this

can lead to accidents.

d) Remove keys and wrenches before switching on the electric tool. A tool or key which comes into contact

with rotating parts of the appliance can lead to injuries.

e) Avoid abnormal working postures. Make sure you stand squarely and keep your balance at all

times. In this way, you can control the electric tool better in unexpected circumstances.

f) Wear suitable work clothes. Do not wear loose clothing or jewellery. Keep hair, clothes and

gloves away from moving parts. Loose clothing, jewellery or long hair can get trapped in moving parts.

g) If vacuuming devices and draining devices can be ﬁtted, make sure that these are correctly

attached and correctly used. The use of a dust extraction system can reduce the danger posed by dust.

4. Usage and treatment of the electric tool

a) Do not overload the appliance. Use the correct tool for your work. You will be able to work better and

more safely within the given performance boundaries.

b) Do not use an electric tool with a defective switch. An electric tool that cannot be switched on or off is

dangerous and must be repaired.

c) Pull the plug out of the socket and/or remove the battery before making any adjustments to

the appliance, changing accessories or put the appliance down. This safety measure prevents starting the

electric tool unintentionally.

d) Keep unused electric tools out of the reach of children. Do not allow people who are not

familiar with the appliance or who have not read these instructions to use the appliance. Electric

tools are dangerous if they are used by inexperienced people.

e) Clean your electric tool carefully. Check whether moving parts are functioning properly and not

jamming, whether parts are broken or damaged enough that the functioning of this electric tool

is affected. Have damaged parts repaired before using the appliance. Many accidents are caused by badly

maintained electric tools.

f) Keep your cutting tools sharp and clean. Carefully maintained cutting tools with sharp cutting edges will jam less

and are easier to control.

g) Make sure to use electric tools, accessories, attachments, etc. in accordance with these

instructions. Take the conditions in your work area and the job in hand into account. Using electric

tools for any purpose other than the one for which they are intended can lead to dangerous situations.

5. Using and handling the cordless tool

a) Only charge the batteries in chargers that are recommended by the manufacturer. A charger that

is designed for a certain type of battery may pose a  re risk if it is used with other types of battery.

b) Use only the correct batteries in the electric tools. The use of other batteries may result in injuries and a re

risk.

c) Keep unused batteries away from paper clips, coins, keys, nails, screws and other metallic

objects that could cause a short circuit between the contacts. A short circuit between the battery contacts

may cause burns or a  re.

d) In case of incorrect use, ﬂuid may escape from the battery. Avoid contact with it. If you touch

it by accident, rinse the affected area with water. If you get the ﬂuid in your eyes, also seek

medical advice. Leaking battery uid can cause skin irritation or burns.

6. Service

a) Have your electric tool repaired only by trained personnel using only genuine spare parts. This will

ensure that your electric tool remains safe to use.

Additional safety instructions We pay a great deal of attention to the design of every battery pack to ensure that we supply

you with batteries which feature maximum power density, durability and safety. The battery cells have a wide range of safety devices.

Each individual cell is initially formatted and its electrical characteristic curves are recorded. These data are then used exclusively

to be able to assemble the best possible battery packs. Despite all the safety precautions, caution must always

be exercised when handling batteries. The following points must be obeyed at all times to ensure

safe use. Safe use can only be guaranteed if undamaged cells are used. Incorrect handling can

cause cell damage.

Important: Analyses conrm that incorrect use and poor care are the main causes of the damage caused by high performance

batteries.

DESCRIPTION OF SYMBOLS

Danger! Read the operating instructions to reduce the risk of inquiry.

Caution Wear ear-muffs. The impact of noise can cause

damage to hearing.

Beware of electrical voltage!

Beware of hot parts.

Double insulated

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its

implementation in national laws, old electric power tools have to be separated from other waste and

disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the manufacturer, the owner of the electrical

equipment must make sure that the equipment is properly disposed of if p1-he no longer wants to keep

the equipment. The old equipment can be returned to a suitable collection point that will dispose of

the equipment in accordance with the national recycling and waste disposal regulations. This does not

apply to any accessories or aids without electrical components supplied with the old equipment.

This consignment contains lithium-ion batteries.

In accordance with special provision 188 this consignment is not subject to the ADR regula-

tions. Handle with care. Danger of ignition in case of damage to the consignment package. If the

consignment package is damaged: Check and if necessary repackage. For further information contact:

0049 1807 10 20 20 66 (xed network 14 ct/min, mobile phone max. 42 ct/min) Outside Germany

charges will apply instead for a regular call to a landline number in Germany.

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers

accompanying products is permitted only with the express consent of the iSC GmbH.

Subject to technical changes

Rated operating voltage and frequency (mains-powered): 220-240V ~ 50 Hz

High Pressure Mode (Compressor)

Rating: 90 W

Max. operating pressure: 11 bar

Theoretical suction rate: 21 liters/min

Output for compressed air at 4 bar: 10 l/min

Output for compressed air at 7 bar: 8 l/min

Compressor no load speed: 3,450/min

High Volume Mode (Low Pressure Blower)

Rating: 90 W

Max. volumetric ow for inating: 400 l/min

Max. volumetric ow for deating: 380 l/min

Blower no load speed: 15,000/min

Power supply (rechargeable battery): 18 V d.c

High Pressure Mode (Compressor)

Max. operating pressure: 11 bar

Theoretical suction rate: 21 liters/min

Output for compressed air at 4 bar: 9 l/min

Output for compressed air at 7 bar: 6 l/min

Compressor no load speed: 3,450/min

High Volume Mode (Low Pressure Blower)

Max. volumetric ow for inating: 390 l/min

Max. volumetric ow for deating: 370 l/min

Blower no load speed: 15,000/min

Sound and vibration values were measured in accordance with EN 60745.

Lpa sound pressure level: 71.5 dB

Kpa uncertainty: 3 dB

Lwa

sound power level: 82.5 dB

Kwa uncertainty: 3 dB

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Keep the noise emissions and vibrations to a minimum.

• Only use appliances which are in perfect working order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

SOUND & VIBRATION

MAINS OPERATION (AC) DATA BATTERY (DC) OPERATION DATA

ELECTRICAL SAFETY

WARNING! When using mains-powered tools, basic safety precautions, including the

following, should always be followed to reduce risk of ﬁre, electric shock, personal injury

and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

Before you connect the charger to the mains supply make sure that the data on the rating plate are identical to the mains data.

This tools charger is double insulated; therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid a hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for

added protection against injury resulting from a possible electrical insulation failure within the tool.

The power supply for this products charger should be protected by a residual current device (rated at 30mA or less). A residual current

device reduces the risk of electric shock.

PXHDIS-240U

AIR IN

4. CONTROLS

2. CONNECTING TO POWER

1. BEFORE USE

Connecting to a 240V (AC) Outlet

KNOW YOUR PRODUCT

3. ADAPTORS & DIGITAL DISPLAY

SETUP & PREPARATION OPERATION

Inserting & Removing the Battery

Attaching Inﬂation Adapters

HYBRID INFLATOR / DEFLATOR

ACCESSORIES

1 2 3 4

9 10 11

5 6 7 8

1 Adapter Compartment

2 Power Mode Switch

3 Pressure Selection Buttons

4 Battery Seating

5 Operation Mode Switch

6 Carry Handle

7 Power Cord Compartment

8 High Volume Air Hose

9 Presta Adapter

10 General Purpose Adapter

11 Ball Adapter

2 To switch the unit on, press the

power mode switch into the DC

position.

3 To remove, press and hold the

battery release tab and pull

the battery away from the

tool.

2 To switch the unit on, press the

power mode switch into the

AC position.

2 Remove the high pressure air

hose from the back of the tool and

unlock the nozzle by lifting the

locking lever.

1 Align the ribs of the battery

with the recess at the front

of the unit and push in until it

clicks into place.

1 Remove the power cord from

the compartment at the base

of the inator and connect to a

240V outlet.

1 Open the side compartment

and remove the desired

ination adapter.

3 Insert the adapter into the

hose nozzle and lock by

pushing down the locking

lever.

The inator unit has 3 adapters to allow a range of functions. All the adapters

are secured in the compartment at the side of the unit.

MODE

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to the

online manual.

BATTERY & CHARGER

This tool is compatible with all batteries and chargers from the Ozito

Power X Change Range.

6. INFLATING HIGH VOLUME ITEMS

The high volume air hose can be used to inate high volume items by

connecting to the air outlet, or deate high volume items by connecting to the

air inlet.

An example of a high volume item is an air mattress or pool toy.

The high pressure air hose can be used to inate high pressure items such as

car and bike tyres or sporting equipment.

WARNING! ENSURE THE INFLATOR INLET IS NOT

BLOCKED DURING INFLATION OR THE OUTLET IS

NOT BLOCKED DURING DEFLATION.

WARNING! AVOID INFLATING THE OBJECT ABOVE

THE RECOMMENDED INFLATION PRESSURE. THIS

MAY LEAD TO DAMAGE AND/OR INJURIES.

5. INFLATING HIGH PRESSURE ITEMS

WARNING! THE 240V POWER SUPPLY SHOULD BE

PROTECTED BY A RESIDUAL CURRENT DEVICE (RATED

AT 30MA OR LESS).

WARNING! BEFORE CONNECTING TO A POWER

SUPPLY, ENSURE THE OPERATING MODE SWITCH IS IN

THE OFF POSITION “0”.

Digital Display

Inﬂating Deﬂating

Preset Pressure

Memory Function

While inating a high pressure item,

the current pressure will be displayed

on the digital display.

Note: When using the inator to

inate or deate a high volume item,

the digital display will show “0.00”.

1 Attach the required ination

adaptor to the high pressure hose

and secure using the locking lever.

1 Follow the steps in the ‘Inating

high pressure items’ section of this

manual to inate the rst item. 3 Press the operating mode switch

into “II” position to start inating

the high volume item.

1 Remove the high volume air

hose from the housing and

attach to the outlet port.

1 Remove the high volume air

hose from the housing and

attach to the inlet port.

3 Adjust the target pressure

using the “+” and “-” pressure

adjustment buttons.

Note: The required pressure should

be written on the item.

5 Once the preset pressure is

reached, the tool will automatically

shut-off.

After the tool has automatically

shut off, press the operation mode

switch into the off position “0”.

2 Increase the preset pressure using

the “+” button or decrease the

pressure using the “-” button.

The preset pressure will be

displayed on the digital display as

it is adjusted.

1 To change between the 3

pressure modes (Bar, PSI or

kPa), press the pressure mode

button.

2 Insert / attach the hose

adaptor to the item to be

inated.

2 Once the operation mode

switch is in the off position

“0”, disconnect the air hose.

Connect the next item and

switch back into mode “I” to

inate the item to the same

preset pressure.

4 Once the item is completely

inated, press the operation

mode switch into the off

position “0”.

2 Insert the adaptor into the

inatable item.

Note: If the inatable item

has a cap or air lock, ensure it is

removed or unlocked to allow air

to ow into the item.

4 Press the operating mode

switch into “I” position to start

inating the high pressure item.

Note: For sporting equipment due to the small size and low pressure, the

inator may automatically cut-off prior to reaching the desired pressure. In

this case, cycle the unit on and off until the required pressure is reached.

Note: If the power supply is disconnected or the power mode switch is

changed, the memory of the tool will be reset.

1 Press the pressure mode

button until the desired

pressure unit is displayed on

the screen.

When using the high pressure hose, a preset pressure can be set so that the

inator will automatically shut-off once the desired pressure is reached.

The inator features a memory function so that once a preset pressure is set,

this value will be remembered until the power supply is disconnected or the

power mode switch is changed.

This function allows you to easily inate multiple items to the same pressure.

MODE

AIR IN

MODE

Items Supplied

Please check that the article is complete as specied in the scope

of delivery. If parts are missing, please contact our service centre or

the sales outlet where you made your purchase at the latest within 5

working days after purchasing the product and upon presentation of

a valid bill of purchase. Also, refer to the warranty table in the service

information at the end of the operating instructions.

• Open the packaging and take out the equipment with care.

• Remove the packaging material and any packaging and/or

transportation braces (if available).

• Check to see if all items are supplied.

• Inspect the equipment and accessories for transport damage.

• If possible, please keep the packaging until the end of the guarantee

period.

Danger!

The equipment and packaging material are not toys. Do not let

children play with plastic bags, foils or small parts. There is a

danger of swallowing or suffocating!

Proper Use

This device is intended for inating car, motorcycle and bicycle tires as

well as sports balls, water balls, air mattresses and other similar items.

In addition the device is also intended for suctioning volumes of air from

objects with low pressure, such as water balls, air mattresses and other

Product specificaties

Merk:	Ozito
Categorie:	Compressor
Model:	PXHDIS-240U

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito PXHDIS-240U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Compressor Ozito

Ozito PXOFCS-636 Handleiding

8 April 2024

Ozito ACK-0015 Handleiding

16 Maart 2024

Ozito ACP-2415 Handleiding

16 Maart 2024

Ozito PXHDIS-240U Handleiding

29 Augustus 2023

Ozito AMC-3000U Handleiding

28 Mei 2023

Ozito ACP-24151U Handleiding

22 Mei 2023

Ozito DMC-1000U Handleiding

20 Mei 2023

Ozito ACK-190U Handleiding

18 Mei 2023

Ozito SAC-2110 Handleiding

16 Mei 2023

Ozito MACP-015 Handleiding

29 Maart 2023

Handleiding Compressor

Nieuwste handleidingen voor Compressor

Einhell TE-AC 300/50/10 Handleiding

4 December 2024

Einhell BT-AC 190/10 Handleiding

4 December 2024

Einhell BT-AC 140/24 OF Handleiding

4 December 2024

Einhell BT-AC 190/24 Handleiding

4 December 2024

Einhell EURO 4300 V Handleiding

4 December 2024

Einhell EURO 210/24 Handleiding

4 December 2024

Einhell KCK 210/8 Handleiding

4 December 2024

Einhell Euro 270/50 Handleiding

4 December 2024

Fieldmann FDAK 70205-0 Handleiding

1 December 2024

Topcraft D-K 210/8 24 Set Handleiding

1 December 2024