Ozito PXCMSK-400U Handleiding

Ozito Zaagmachine PXCMSK-400U

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PXCMSK-400U (3 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

SPECIFICATIONS

Voltage: 18V

No Load Speed: 3,000/min

Blade: 210 x 30 x 1.8mm

Blade Teeth: 40TCT

Laser Class: 2

Laser Wavelength: 650nm

Laser Output: ≤1mW

Cutting Capacity:

0° Mitre x 0° Bevel: 120x60mm

45° Mitre x 0° Bevel: 83x60mm

0° Mitre x 45° Bevel: 120x34mm

45° Mitre x 45° Bevel: 83x34mm

Weight: 9.3kg

210MM

MITRE SAW

ORIGINAL INSTRUCTIONS

ozito-diy.co.uk

Compound Mitre Saw

DESCRIPTION OF SYMBOLSOPERATION

MITRE SAW SAFETY WARNINGS

Hex Key

Material Clamp

Dust Bag

PXCMSS-210U

Art.-No.: 30.002.79 I.-No.: 11017

Danger! Read the operating instructions to reduce the risk of inquiry.

On/Off switch for laser

On/Off switch for LED lamp

Warning! To make mitre cuts (with the saw

head inclined or the turtable set at an angle),

the adjustable stop rail must be xed at an outer

position.

To make 90 crosscuts, the adjustable stop rail must °

be xed at the inner position.

Caution! Wear ear-muffs. The impact of noise can cause

damage to hearing.

Caution! Wear a breathing mask. Dust which is injurious to

health can be generated when working on wood and other materials. Never

use the device to work on any materials containing asbestos!

Caution! Wear safety goggles. Sparks generated during

working or splinters, chips and dust emitted by the device can cause

loss of sight.

STANDARD EQUIPMENT

WARRANTY

OZITO UK Champion’s Business Park, Unit 10, 1st Floor, Arrowe Brook Road, Upton, Wirral, Merseyside, CH49 0AB 0318

All of our products undergo strict quality checks to ensure that they reach you in perfect

condition. In the unlikely event that your device develops a fault, please contact our service

department at the address shown on this guarantee card. You can also contact us by

telephone using the customer service number shown. Please note the following terms under

which guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the manufacturer

mentioned below promises to buyers of its new products in addition to their statutory

guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or manufacturing faults on

a product which you have bought from the manufacturer mentioned below are limited to

either the rectication of said defects on the product or the replacement of the product,

whichever we prefer.

Please note that our devices are not designed for use in commercial, trade or professional

applications. A guarantee contract will not be created if the device has been used by

commercial, trade or industrial business or has been exposed to similar stresses during the

guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly instructions or due to

incorrect installation, a failure to follow the operating instructions (for example connecting

it to an incorrect mains voltage or current type) or a failure to follow the maintenance and

safety instructions or by exposing the device to abnormal environmental conditions or by

lack of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example overloading the

device or the use or unapproved tools or accessories), ingress of foreign bodies into the

device (such as sand, stones or dust, transport damage), the use of force or damage caused

by external forces (for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural wear or tear or by

normal use of the device.

4. Your Product is guaranteed for a period of 60 months from the original date of purchase

and is intended for DIY (Do It Yourself) use only. Lithium Ion batteries and chargers are

covered by a 12 month warranty. Warranty excludes consumable parts. Guarantee claims

should be submitted before the end of the guarantee period within two weeks of the defect

being noticed. No guarantee claims will be accepted after the end of the guarantee period.

The original guarantee period remains applicable to the device even if repairs are carried

out or parts are replaced. In such cases, the work performed or parts tted will not result

in an extension of the guarantee period, and no new guarantee will become active for the

work performed or parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO

THE PLACE OF PURCHASE WITH YOUR REGISTER RECEIPT.

Please refer to the restrictions of this warranty concerning wearing parts, consumables and

missing parts as set out in the service information in these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

GENERAL POWER TOOL SAFETY WARNINGS

DANGER! Read all safety information, instructions, illustrations and technical data

provided on or with this power tool. Failure to adhere to the following instructions may

result in electric shock, ﬁre and/or serious injury.

Keep all safety information and instructions in a safe place for future use. The term “power tool“ used

in the safety information and instructions refers to power tools operated from the mains power supply (with a power cable) and to

battery operated power tools (without a power cable).

1. Workplace safety

a) Keep your work area clean and well illuminated. Untidy or unlit work areas can result in accidents.

b) Do not operate the electric tool in an environment where there is a risk of explosions and

where there are inﬂammable liquids, gases or dust. Electric tools produce sparks which could set the dust or

vapours alight.

c) Keep the electric tool out of the reach of children and other persons. If there is a distraction, you may

lose control of the appliance.

2. Electrical safety

a) The connector plug from this electric tool must ﬁt into the socket. The plug should never be

altered in any way. Never use adapter plugs together with earthed electric tools. Unaltered plugs and

correct sockets reduce the risk of an electric shock.

b) Avoid bodily contact with earthed surfaces such as pipes, heating, ovens and fridges. The risk of

electric shock is increased if your body is earthed.

c) Keep the tool out of the rain and away from moisture. The ingress of water into an electric tool increases the

risk of an electric shock.

d) Do not use the cable to carry the electric tool, to hang it up or to pull it out of the socket.

Keep the cable away from heat, oil, sharp edges and moving parts of the appliance. Damaged or

entangled cables increase the risk of an electric shock.

e) If you are working outdoors with an electric tool, only use extension cables which are designed

speciﬁcally for this purpose. Using specially designed outdoor extension cables, the risk of electric shock is reduced.

f) If operation of the electric tool in a damp environment can not be avoided, use a earth-leakage

circuit-breaker. The earthleakage circuit-breaker reduces the risk of an electric shock.

3. Safety of persons

a) Be careful, watch what you are doing and use an electric tool sensibly. Do not use the tool if

you are tired or under the inﬂuence of drugs, alcohol or medication. A moment of inattention when using the

electric tool can result in serious injuries.

b) Wear personal protection equipment and always wear safety goggles. Wearing personal protection

(such as dust masks, non-slip safety shoes, safety helmet or ear protection, depending upon the type and use of the electric tool)

reduces the risk of injury.

c) Make sure that the appliance cannot start up accidentally. Ensure that the electric tool is switched off

before you connect it to the power supply and/or insert the battery, or pick up or carry the tool. If your nger is on the switch whilst

carrying the electric tool or if you connect the appliance to the mains when it is switched on, this can lead to accidents.

d) Remove keys and wrenches before switching on the electric tool. A tool or key which comes into contact

with rotating parts of the appliance can lead to injuries.

e) Avoid abnormal working postures. Make sure you stand squarely and keep your balance at all

times. In this way, you can control the electric tool better in unexpected circumstances.

f) Wear suitable work clothes. Do not wear loose clothing or jewellery. Keep hair, clothes and

gloves away from moving parts. Loose clothing, jewellery or long hair can get trapped in moving parts.

g) If vacuuming devices and draining devices can be ﬁtted, make sure that these are correctly

attached and correctly used. The use of a dust extraction system can reduce the danger posed by dust.

4. Usage and treatment of the electric tool

a) Do not overload the appliance. Use the correct tool for your work. You will be able to work better and

more safely within the given performance boundaries.

b) Do not use an electric tool with a defective switch. An electric tool that cannot be switched on or off is

dangerous and must be repaired.

c) Pull the plug out of the socket and/or remove the battery before making any adjustments to

the appliance, changing accessories or put the appliance down. This safety measure prevents starting the

electric tool unintentionally.

d) Keep unused electric tools out of the reach of children. Do not allow people who are not

familiar with the appliance or who have not read these instructions to use the appliance. Electric

tools are dangerous if they are used by inexperienced people.

e) Look after power tools and plug-in tools with care. Check that moving parts function correctly

and do not jam, and whether any parts are broken or damaged such that they adversely affect

the function of the power tool. Have damaged parts repaired before you use the tool. Many accidents

are caused by poorly maintained electric tools.

f) Keep your cutting tools sharp and clean. Carefully maintained cutting tools with sharp cutting edges will jam less

and are easier to control.

g) Make sure to use electric tools, accessories, attachments, etc. in accordance with these instructions.

Take the conditions in your work area and the job in hand into account. Using electric tools for any purpose other than the one for

which they are intended can lead to dangerous situations.

h) Keep the handles and grip surfaces dry,clean and free from oil and grease. If the handles and grip

surfaces are slippery, it will not be possible to operate and control the power tool safely in unforeseen situations.

5. Using and handling the cordless tool

a) Only charge the batteries in chargers that are recommended by the manufacturer. A charger that

is designed for a certain type of battery may pose a  re risk if it is used with other types of battery.

b) Use only the correct batteries in the electric tools. The use of other batteries may result in injuries and a re

risk.

c) Keep unused batteries away from paper clips, coins, keys, nails, screws and other metallic

objects that could cause a short circuit between the contacts. A short circuit between the battery contacts

may cause burns or a re.

d) In case of incorrect use, ﬂuid may escape from the battery. Avoid contact with it. If you touch

it by accident, rinse the affected area with water. If you get the ﬂuid in your eyes, also seek

medical advice. Leaking battery uid can cause skin irritation or burns.

e) Never use damaged or altered rechargeable batteries. Damaged or altered rechargeable batteries can behave

unpredictably and lead to a risk of re, explosion or injury.

f) Never expose a rechargeable battery to ﬁre or high temperatures. Fire or temperatures over 130°C pose

a risk of explosion.

g) Follow all the instructions on charging and never charge the rechargeable battery or cordless

tool outside the speciﬁed allowable charging temperature range.

Incorrect charging or charging outside the allowable charging temperature range could cause irreparable damage to the battery and

increase the risk of re.

6. Service

a) Have your electric tool repaired only by trained personnel using only genuine spare parts. This will

ensure that your electric tool remains safe to use.

b) Never perform maintenance work on damaged rechargeable batteries. All maintenance work on

rechargeable batteries should only be performed by the manufacturer or authorized after sales service outlets.

a) Miter saws are designed for cutting wood or wood-type products. They are not intended to be used for

cutting ferrous materials such as rods, bars, screws, etc. Abrasive dust will lead to moving parts such as the bottom guard hood

getting blocked. Sparks from cutting will burn the bottom guard hood, the insertion plate and other plastic parts

b) If possible, use clamps to secure the workpiece. If you hold the workpiece with your hand, you must keep your

hand at least 100 mm away from each side of the saw blade at all times. Never use this saw for cutting workpieces which are too

small, to clamp them or to hold them with your hand. If your hand is too close to the saw blade there is a greater risk of injury from

contact with the saw blade.

c) The workpiece must immovable and either securely clamped or pressed against the stop and

the table. Do not push the workpiece into the saw blade and never cut it “free-handed”. Loose or moving workpieces could be

catapulted out at high speed and cause injuries.

d) Push the saw through the workpiece. Do not pull the saw backwards through the workpiece. To make a cut, lift the

saw head and pull it over the workpiece without cutting. Then switch on the motor, swing the saw head down and push it through the

workpiece. If it is pulled to make a cut there is a danger of the saw blade leaping up on the workpiece and the saw blade unit being

hurled with force against the operator.

e) Never cross your hand over the intended cutting line, either in front of or behind the saw

blade. Supporting the workpiece “with crossed hands”, i.e. holding the workpiece on the right-hand side next to the saw blade with

your left hand or vice versa is very dangerous.

f) Do not reach behind the stop while the saw blade is rotating. Never place your hands any closer to the

rotating saw blade than the safety distance of 100 mm (this applies to both sides of the saw blade, e.g. when removing wood scraps).

You may not necessarily be able to see how close your hands are to the rotating saw blade and you could sustain serious injuries.

g) Check the workpiece before cutting. If the workpiece is bent or warped, clamp it with the side which is curved

outward facing towards the stop. Always make sure that there are no gaps along the cutting line between the workpiece, stop and

table. Bent and warped workpieces could twist or move position and cause the rotating saw blade to get jammed during cutting.

There must be no nails or foreign bodies in the workpiece.

h) Do not use the saw before all tools, wood scraps, etc., have been cleared from the table; only the workpiece

is allowed to be on the table. Small scraps, loose pieces of wood and other objects which come into contact with the rotating blade

could be catapulted out at high speed.

i) Only cut one workpiece at a time. Stacks of more than one workpiece cannot be clamped or held properly and could

cause the blade to jam or slip while sawing.

j) Make sure that the miter saw is stood on a level and ﬁrm work surface before you start using

it. A level and rm work surface will prevent any danger of the miter saw becoming instable.

k) Plan your work. Whenever you adjust the angle of the saw blade or the miter angle, make sure that adjustable stop is

correctly adjusted and supports the workpiece without coming into contact with the blade or the guard hood. With the machine

switched off and without the workpiece on the table, perform a simulation of the complete movement of the saw blade in order to

check that there are no obstructions and there is no risk of cutting into the stop.

l) Where workpieces are wider or longer than the table top, make sure that you provide

appropriate support for the workpiece, e.g. in the form of table extensions or sawing trestles. Workpieces which are

longer or wider than the table of the miter saw could tilt if they are not supported securely. If a piece of wood which has been cut off

or the workpiece tilts, it could push the bottom guard hood up or be catapulted out by the rotating saw blade out of control.

m) Do not use the assistance of another person as a substitute for a table extension or additional

support. Instable support for the workpiece could cause the saw blade to jam. In addition, the workpiece could also move while

the cut is being performed and pull you and your helper into the rotating blade.

n) The piece which has been cut off must not be pressed against the rotating saw blade. If space is

restricted, e.g. if length stops are used, the piece which has been cut off could get wedged in the blade and then hurled out of control.

o) The equipment is not allowed to be used for cutting round material. Rods or poles have a tendency to roll

away during cutting, which could result in the blade “catching” and the workpiece in your hand being drawn into the blade.

p) Allow the blade to reach its full before you cut in the workpiece. This will reduce the risk of the workpiece

being catapulted away.

q) If the workpiece gets jammed or the blade gets blocked, switch off the miter saw. Wait until all

moving parts have come to a standstill, pull out the power plug and/or take out the rechargeable battery. Then remove the jammed

material. If you continue sawing when such a blockage occurs, this could lead to a loss of control or damage to the miter saw.

r) Release the switch when the cut has been completed, hold the saw head down and wait until

the blade has come to a standstill before you remove the piece which has been cut off . It is

extremely dangerous to reach with your hand into the area anywhere near the blade while it is slowing down.

s) Hold the handle very ﬁrmly if you want to make an incomplete cut or if you release the switch

before the saw head has reached its bottom position. The braking effect of the saw could cause the saw head to

be pulled down with a jerk, leading to a risk of injury.

Additional safety precautions:

• Use saw blades which are designed for the purpose and for the material being cut.

• Use only blades which are recommended by the manufacturer and comply with EN 847-1.

• Use only blades with diameters, hole diameters and tooth pitches which conform with the

technical data set out in the original operating instructions.

• Use only blades with rotating speeds shown on the blade which are equal to or higher than the

rotating speed shown on the power tool.

• Do not use saw blades that are blunt, bent or damaged.

• Check the direction of rotation whenever you change the saw blade. There are arrows marked on the

machine and saw blade to show the direction of rotation. They must match.

• Wear gloves to avoid getting cut when you transport and change the saw blades. Whenever

practicable, saw blades must be carried in a container.

• Before use, check that the safety guard for the saw blade is in proper working order. If it does

not close automatically or is damaged, do not use the equipment any more. In this case, contact the manufacturer or an authorized

customer service outlet to get it professionally repaired.

• If a switch is damaged or defective, arrange for it to be replaced by the manufacturer or an

authorized customer service outlet.

• Replace worn or damaged table inserts in the saw table with a replacement part, or arrange

for them to be replaced by the manufacturer or an authorized customer service outlet.

• Only allow repairs to the equipment to be carried out by the manufacturer or an authorized

customer service outlet using original parts, otherwise the user may suffer an accident.

• Connect a dust extractor to the extractor adapter on the machine.

• Make sure that there is adequate stability by always securing the machine to a workbench or a

table. Use the holes in the machine‘s base frame to secure the machine. Bolt the base frame to a workbench or a table.

• Secure long workpieces against falling off, e.g. using standard roller stands.

• The extensions to the workpiece support must be fastened and used at all times while work is

in progress

• The machine is designed for cutting wood and wood-type materials. To prevent the saw blade overheating,

perform cuts quickly using blades that are properly sharpened.

• Do not use the saw to cut ﬁre wood.

• The clamping device for securing the workpiece must be used at all times. Do not cut workpieces which

are too small to clamp securely with the clamping device.

• Transport the machine by the carry handles and the machine’s base frame only.

• If the machine is equipped with a laser, this laser may not be replaced by a different type of

laser. Repairs to the laser are only allowed to be carried out by the manufacturer or an authorized customer service outlet.

• The saw blade must be stationary whenever you carry out any tidying up or cleaning work. Do not

remove any cutting residues or other parts of workpieces from the cutting zone while the machine is running and the saw unit is not

at rest (at the top).

• If you need to use an extension cable, use one with a minimum cross-section of 1.5 mm² to

ensure that the machine is supplied with power.

• If you use a cable reel, the complete cable must be pulled off the reel.

• Keep children and other people away from the equipment. When not in use, stow the equipment in a location

that is out of reach of children and unauthorized users.

• Pull out the power plug (or take out the rechargeable battery) and check that the blade does

not touch the table or workpiece stop in any cutting position.

• Adopt a safe working position for your work to ensure that neither of your hands could come

into contact with the saw blade if they suddenly slip.

• Always stand to the side of the saw blade when working.

Caution! Take extra care when making double miter cuts.

• To rectify faults or remove jammed pieces of wood, always switch off the machine ﬁrst. Always pull

out the power plug (or take out the rechargeable battery).

• Be sure to observe the safety information and operating and maintenance instructions issued by

the manufacturer, as well as the maximum workpiece dimensions listed in the technical data.

• Be sure to observe the accident prevention regulations in force in your area as well as all other

generally recognized rules of safety. If you are inexperienced in the use of the machine, you can seek the advice of a

qualied professional or attend courses to become trained in using the machine.

Keep the safety information and original operating instructions in a safe place and pass them on

with the machine if you hand the machine on to another person.

Caution! Risk of injury! Do not reach into the running saw blade.

Double insulated

SPARE PARTS

MAINTENANCE & TROUBLESHOOTING

Spare parts can be ordered from the Special Orders Desk at your local

Bunnings Warehouse or Homebase store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: info@ozito-diy.co.uk

SERVICE INFORMATION

Please note that the following parts of this product are subject to normal or natural

wear and that the following parts are therefore also required for use as consumables.

* Not necessarily included in the scope of delivery!

Category Example

Wear parts* Carbon brushes, Battery

Consumables* Saw blade

Missing parts

DECLARATION OF CONFORMITY

Wentao/Product-ManagementWeichselgartner/General-Manager

explains the following conformity according to EU directives and norms for

the following product

Cordless Compound Mitre Saw PXCMSS-210U (Ozito)

2014/29/EU

2005/32/EC_2009/125/EC

2014/35/EU

2006/28/EC

X 2014/30/EU

2014/32/EU

2014/53/EC

2014/68/EU

90/396/EC_2009/142/EC

89/686/EC_96/58/EC

X 2011/65/EU

X 2006/42/EC

Annex IV

Noti ed Body:

Noti ed Body No.:

Reg. No.:

2000/14/EC_2005/88/EC

Annex V

Annex VI

Noise: measured LWA

= dB (A); guaranteed LWA

= dB (A)

P = KW; L/Ø = cm

Noti ed Body:

2012/46/EU

Emission No.:

Standard references: EN 62841-1; EN 62841-3-9; EN 55014-1; EN 55014-2

Landau/Isar, den 06.03.2018

First CE: 17 Archive-File/Record: NAPR018264

Art.-No.: 30.002.79 I.-No.: 11017 Alex KurzDocuments registrar:

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its

implementation in national laws, old electric power tools have to be separated from other waste and

disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the manufacturer, the owner of the electrical

equipment must make sure that the equipment is properly disposed of if p1-he no longer wants to keep

the equipment. The old equipment can be returned to a suitable collection point that will dispose of

the equipment in accordance with the national recycling and waste disposal regulations. This does not

apply to any accessories or aids without electrical components supplied with the old equipment.

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers

accompanying products is permitted only with the express consent of the iSC GmbH.

Subject to technical changes

SOUND & VIBRATION

Sound and vibration values were measured in accordance with EN 62841.

Lpa sound pressure level: 91.2 dB

Kpa uncertainty: 3 dB

Lwa

sound power level: 104.2 dB

Kwa uncertainty: 3 dB

Wear ear-muffs.

The impact of noise can cause damage to hearing.

The stated vibration emission levels and stated noise emission values were measured in accordance

with a set of standardized criteria and can be used to compare one power tool with another.

Keep the noise emissions and vibrations to a minimum.

• Only use appliances which are in perfect working order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

• Wear protective gloves.

ELECTRICAL SAFETY

WARNING! When using mains-powered tools, basic safety precautions, including the

following, should always be followed to reduce risk of ﬁre, electric shock, personal injury

and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

Before you connect the charger to the mains supply make sure that the data on the rating plate are identical to the mains data.

This tools charger is double insulated; therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid a hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for

added protection against injury resulting from a possible electrical insulation failure within the tool.

The power supply for this products charger should be protected by a residual current device (rated at 30mA or less). A residual

current device reduces the risk of electric shock.

7. MAKING A CUT

2 Secure the

workpiece and

ensure all mitre saw

adjustments are

locked tightly.

4 Perform the cut

through the timber

smoothly. Once

complete, release

the on/off trigger

and remove the

saw from the work

piece.

For instructions on changing the blade, making saw alignment

adjustments, or troubleshooting, see separate maintenance

instruction manual.

1 Mark the cutting line on the work

piece and then place onto the

mitre table with one edge up

against the rear fence.

3 Start the saw and allow the

blade to reach full speed.

Note: Never force the saw. Use light and continuous pressure.

1. BEFORE USE

Items Supplied

Please check that the article is complete as specied in the scope of delivery.

If parts are missing, please contact our service center or the sales outlet where

you made your purchase at the latest within 5 working days after purchasing

the product and upon presentation of a valid bill of purchase. Also, refer to the

warranty table in the service information at the end of the operating instructions.

• Open the packaging and take out the equipment with care.

• Remove the packaging material and any packaging and/or transportation braces

(if available).

• Check to see if all items are supplied.

• Inspect the equipment and accessories for transport damage.

• If possible, please keep the packaging until the end of the guarantee period.

Danger!

The equipment and packaging material are not toys. Do not

let children play with plastic bags, foils or small parts. There

is a danger of swallowing or suffocating!

Proper Use

The cordless crosscut saw is designed for crosscutting wood and wood-type

materials which are appropriate for the machine’s size. The saw is not designed for

cutting rewood.

The equipment is to be used only for its prescribed purpose. Any other use is

deemed to be a case of misuse. The user / operator and not the manufacturer will

be liable for any damage or injuries of any kind caused as a result of this.

Please note that our equipment has not been designed for use in commercial, trade

or industrial applications. Our warranty will be voided if the machine is used in

commercial, trade or industrial businesses or for equivalent purposes.

Caution!

Residual risks

Even if you use this electric power tool in accordance with

instructions, certain residual risks cannot be rules out.

The following hazards may arise in connection with the

equipment’s construction and layout:

1. Lung damage if no suitable protective dust mask is used.

2. Damage to hearing if no suitable ear protection is used.

3. Health damage caused by hand-arm vibrations if the equipment is used over a

prolonged period or is not properly guided and maintained.

3. EXTENSION SUPPORTS 4. ADJUSTMENTS

Bevel Adjustment

Mitre Adjustment

20 40 50 60 100 120 140 160 180

20 40 50 60 100 120 140 160

2 Tilt the head using

the bevel scale as a

reference.

2 Rotate the mitre

table to the desired

mitre angle and

then lock in position

using the mitre

locking knob.

1 Loosen bevel locking lever at the

rear of the saw.

1 Loosen the mitre locking knob at

the front of the saw.

3 Tighten the bevel locking lever

to secure at the desired bevel

angle.

WARNING! ENSURE THE BEVEL LOCK IS TIGHT

BEFORE MAKING A CUT. FAILURE TO DO SO MAY

RESULT IN THE CUTTING HEAD MOVING DURING

OPERATION AND CAUSE SERIOUS PERSONAL INJURY.

Note: The mitre table features positive click stops at 0°, 5°, 10° 15°, 22.5°,

30°, 35°, 40° and 45° for quick setting of common mitre angles.

OFF

Laser Line Worklight

OFF

Laser Line Worklight

OFF

1 To unlock the saw head, press

down slightly on the handle and

then pull and rotate the head

locking pin 90 degrees.

2 To lock the head down, press

the head down and the pull and

rotate the head locking pin 90

degrees.

To switch the worklight on, press

the worklight switch up into the on

position.

To switch the laser line on, press

the laser line switch up into the on

position.

5. CONTROLS

WARNING! DO NOT STARE DIRECTLY AT THE LASER

BEAM OR WORKLIGHT.

Starting the Mitre Saw

Head Locking Pin

Turning On the Worklight or Laser Line

2 Squeeze the on/off

trigger to start the

saw.

Note: Allow the saw to reach full speed before beginning a cut.

1 Unlock the trigger by pressing the

lever on the trigger sideways.

Then unlock the handle motion by

pressing the handle lock button

at the front of the handle.

6. VARIOUS CUTS

WARNING! DO NOT USE THE MITRE SAW TO CUT

METAL OR MASONRY.

CAUTION! FOR ALL TYPES OF CUTS ENSURE THE SAW

IS LOCKED INTO POSITION.

20 40 50 60 100 120 140 160 180

45 0

450

20 40 50 60 100 120 140 160 180

Straight Cutting

Mitre Cuts

Bevel Cutting

Compound Mitre Cuts

A straight cut is made by cutting

the grain of the workpiece. A 90°

straight cut is made with the mitre

scale set in the 0°.

Mitre cuts are made with the mitre

scale set at an angle other than 0°.

A bevel cut is made by cutting across

the grain of the workpiece with the

blade angled to the mitre table.

A compound mitre cut involves using

a mitre angle and a bevel angle at

the same time.

WARNING! ENSURE THE TOOL IS SWITCHED OFF AND

THE BATTERY IS REMOVED BEFORE PERFORMING ANY

OF THE FOLLOWING TASKS.

2. FITTING THE BATTERY & CLAMP

Inserting & Removing the Battery

1 Slide the battery into the seating

above the saw handle until it

clicks into place.

2 To remove, press and

hold the battery release

tab and then slide out.

The extension supports can be extended outwards allowing additional support

when cutting longer workpieces.

The extension supports allow feature a material stop that can be raised in

order to contact the end of the workpiece. This feature is used to quickly

position material enabling you to cut multiple pieces at the same length.

Attaching / Adjusting the Material Clamp

Adjusting the Extension Supports

Using the Material Stops

Fence Adjustment

20 4

20 40 50

2 Adjust the material

clamp into the

desired location and

tighten all locking

knobs.

2 Slide the extension

support to the

desired location

and then release

the locking lever to

secure in position.

2 Once the material

stop is set, you can

place the workpiece

onto the table and

slide up to the stop.

Secure the material

and then complete

the cut.

1 Loosen the clamp locking knobs

and insert the shaft into the hole.

Note: The clamp can be mounted on

either side of the blade.

Note: When performing bevel cuts, the work clamp must be on the opposite

side of the bevel (otherwise it will interfere with the cutting action).

1 Press the support locking lever

underneath the support arm to

allow it to slide.

1 Raise the material stop upwards,

then adjust the extension support

to the desired distance away

from the blade.

1 Make sure that no part of the

tool contacts the upper fence

when bevel or compound mitre

cutting.

Note: Always make a dry run with

the saw turned off and check

clearance. Tighten securely before

making a cut.

3 The large screw can be lowered

onto the timber workpiece in

order to secure the workpiece

while performing a cut.

PXCMSS-210U

KNOW YOUR PRODUCT SETUP & PREPARATION OPERATION

CORDLESS MITRE SAW

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to the

online manual.

BATTERY & CHARGER

This tool is compatible with all battery and chargers from the Ozito

Power X Change Range.

For optimal performance, p2-we recommend the use of a 3.0Ah battery or

higher to operate this Power X Change Mitre Saw.

1 Handle Lock Button

2 Spindle Lock

3 Head Locking Pin

4 Material Clamp

5 Extension Supports

6 On/Off Trigger

7 Bevel Guide

8 Rear Fence

9 Mitre Guide

10 Mitre Locking Knob

11 Blade

12 Lower Blade Guard

13 Depth Stop

14 Dust Port

15 Bevel Locking Lever

16 Material Stop

Side View

Front View

20 40 50 60 100 120 140 160 180

Trenching refers to restricting the depth of cut and permits a “trench” to be

cut in the workpiece.

Depth Adjustment (Trenching)

2 Using a hex key,

adjust the depth

adjustment screw

so that the cutting

head stops at the

desired height when

lowered.

1 Ensure the cutting head is raised,

and then loosen the depth

locking nut.

3 Once the desired setting is

achieved, tighten the depth

locking nut.

Product specificaties

Merk:	Ozito
Categorie:	Zaagmachine
Model:	PXCMSK-400U

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito PXCMSK-400U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Zaagmachine Ozito

Ozito PXCCSK-4182 Handleiding

23 Augustus 2024

Ozito PXBPCK-1825 Handleiding

23 Augustus 2024

Ozito PXTCSK-2520 Handleiding

23 Augustus 2024

Ozito PXPRSS-018 Handleiding

30 Juli 2024

Ozito PXBPCS-1815 Handleiding

30 Juli 2024

Ozito JSW-6100U Handleiding

9 Juli 2023

Ozito RSW-5200 Handleiding

26 Juni 2023

Ozito JSW-4000U Handleiding

24 Juni 2023

Ozito JSW-8100U Handleiding

20 Juni 2023

Ozito RSW-5200U Handleiding

18 Juni 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Anova E60CS Handleiding

20 December 2024

Silverline 447132 Handleiding

19 December 2024

Silverline 427644 Handleiding

19 December 2024

Herkules KS 210 Profi Handleiding

17 December 2024

Total TS730301 Handleiding

16 December 2024

Total TJSLI8501 Handleiding

16 December 2024

Turbo-Silent EKS 2040/1 Handleiding

16 December 2024

Bavaria BJS 400 Handleiding

5 December 2024

Bavaria BCS 64/1 Handleiding

5 December 2024

Bavaria BEC 2040 TC Handleiding

5 December 2024