Ozito PXBCS-1830 Handleiding
Ozito
Zaagmachine
PXBCS-1830
Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PXBCS-1830 (8 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
PXBCS-1830
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other
than that specied on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty Warranty excludes consumable parts, for example: guide bar, chain
and included accessories.
OZITO. 25 Fox Drive, Dandenong South, Victoria 3175, Australia
MIN
300
MM
(12”)
MIN
300
MM
(12”)
STANDARD EQUIPMENT
Chainsaw
CHAINSAW
INSTRUCTION MANUAL
ozito.com.au
Guide Bar Cover
Guide Bar & Chain
SPECIFICATIONS
Input: 18V
Bar Length: 300mm (12”)
Cutting Length: 270mm max.
Chain Speed: 6.0 / 8.9 m/s
Chain Pitch: 9.53mm (3/8”)
Chain Gauge: 1.1mm (0.043”)
Oil Tank: 160ml max.
Sound Power Level: 100 dB
Weight: 4.03kg
0824
This product is intended for use by a competent
trained person. This user manual is a guide only and
should not be treated as a training manual.
• Please seek professional training before use.
• This product is designed for felling small trees, limbing of branches,
sawing wooden beams and pruning of trees, shrubs and bushes while
user is rmly footed on the ground.
1. ASSEMBLY
MIN
300
MM
(12”)
MIN
MIN
300
MM
(12”)
300
MM
(12”)
30
AB
4. Place the guide bar
and chain in position,
ensuring that the chain
is around sprocket
(A). Also ensure that
the threaded pin (B)
ts into the guide bar
tension dial.
If it does not t, it can
be adjusted slightly by
turning the dial.
5. Attach the side cover and secure it with
the guide bar lock knob. Do not fully
tighten the guide bar lock knob until after
adjusting the chain tension.
1. Completely unscrew the guide bar
lock knob, rotating in a counter
clockwise direction.
Fitting the Chain & Bar
2. Remove the side cover.
3. Fit the chain over the guide bar,
making sure that the cutters are
facing in the direction of rotation.
IMPORTANT: IF THE CHAIN IS INSTALLED BACKWARDS
(CHAIN CUTTERS ARE FACING IN THE OPPOSITE DIRECTION
OF ROTATION) THE CHAINSAW WILL VIBRATE EXCESSIVELY
AND NOT CUT.
WARNING!: ENSURE THE CHAINSAW IS SWITCHED
OFF AND THE BATTERY IS DISCONNECTED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
WARNING!: ALWAYS WEAR GLOVES WHEN HANDLING
THE CHAIN. THE CHAIN CUTTERS ARE SHARP AND
COULD CUT YOU.
KNOW YOUR PRODUCT SETUP & PREPARATION
1. Rear Handle
2. On/Off Trigger
3. Oil Level Window
4. Side Cover
5. Guide Bar Lock Knob
6. Hand Guard/Chain Brake
7. Chain Tension Dial
8. Guide Bar
9. Chain
10. Bucking Spikes
11. Front Handle/Carry Handle
12. Speed Control
13. Oil Tank Cap
14. Motor Cover
15. Battery Seating
16. Lock-Off Button
17. Guide Bar Cover
BRUSHLESS CHAINSAW
BATTERY & CHARGER
This tool is compatible with all battery and chargers
from the Ozito PXC Range.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
1 3 4 6 7 8
1410 11
9
1512 13
2 5
16
17
For convenience and ease of assembly, the chain is pre-tted over the
guide bar with the cutters facing in the direction of rotation. Refer to the
supplied A5 insert for further information before tting the bar & chain
for the rst time.
2. OIL
300
MM
(12”)
300
MM
(12”)
3 - 4mm gap is
the ideal tension
300
MM
(12”)
MIN
300
MM
(12”)
Note: Proper tension of the
chain is extremely important
and must be checked before
starting, as well as during any
cutting operation. Taking the
time to make adjustments to the chain will result in improved cutting
performance and prolonged chain life.
WARNING!: DO NOT OPERATE THIS CHAINSAW WITH
LONG LOOSE HAIR OR LOOSE FITTING JEWELLERY. TIE
LONG LOOSE HAIR BACK AND REMOVE LOOSE FITTING
JEWELLERY.
IMPORTANT: IF YOU TRY TO ROTATE THE CHAIN TENSIONING
DIAL WHILST THE GUIDE BAR LOCK KNOB IS TIGHT, IT WILL
RESULT IN THE CHAIN NOT LOOSENING AND POSSIBLE
DAMAGE TO THE MECHANISM.
Adjusting the Chain Tension
1. Loosen the guide bar lock knob,
rotating in a counter clockwise
direction.
2. Adjust the chain tension
with the chain tensioning
dial. Turning the dial
CLOCKWISE increases
the chain tension, turning
it COUNTER-CLOCKWISE
decreases the chain
tension.
For the correct chain tension, rmly
pull up on the chain at the middle
of the top of the exposed guide bar.
When the chain is pulled up to its
highest point, the bottom tip of the
links should only just stay in the
track [middle of the guide bar].
3. After the chain has been
accurately tensioned, lock
the guide bar in place with
the guide bar lock knob.
Note: Chain bar oil may leak if the chainsaw is left for long periods.
This is normal. If the chainsaw is to be left unused for an extended
time, drain the oil from the oil tank. Rell before use.
5. To check the lubricating
system, switch on the
chainsaw and hold it with
the guide bar and chain
above some light coloured
paper such as newspaper.
A steadily increasing stain
caused by oil spray shows
the lubricating system is
working.
2. Fill the tank with chain bar oil. The
capacity of the chain oil tank is
160ml. Do not over ll.
4. Always ll the oil tank when the
oil level is below the minimum
mark on the oil level window.
Note: Always clean up any oil
spillage from product or area with an
absorbent towel before use. Always
discard waste according to your Local
government policies and laws.
WARNING!: NEVER START WORK UNLESS THE
CHAIN AND BAR ARE LUBRICATED. USE OF THE
CHAINSAW WITHOUT SAW CHAIN OIL OR IF THE OIL
LEVEL IS BELOW THE ‘MIN’ MARK WILL DAMAGE THE
CHAINSAW.
1. Place the chainsaw on a level
surface, then unscrew the chain
bar oil cap.
3. Ret cap and clean any oil spillage before placing the chainsaw back
in the upright position.
IMPORTANT: ONLY USE OIL THAT IS EXPRESSLY LABELLED
‘CHAIN BAR OIL’.
Running in the Chain
Prior to operation, a new chain should be run in for 2–3 minutes
and then its tension should be checked and adjusted as detailed in
‘ASSEMBLY - Adjusting the Chain Tension’.
WARNING!: WHEN TRANSPORTING THE CHAINSAW
FROM ONE LOCATION TO ANOTHER, ALWAYS CARRY BY
THE FRONT HANDLE ONLY, NEVER CARRY HOLDING THE
BLADE AS IT IS SHARP AND WILL CUT YOU.
IMPORTANT: IT IS VITAL FOR THE PROPER AND SAFE
OPERATION OF THE CHAINSAW THAT THE CHAIN IS TENSIONED
CORRECTLY.
Product specificaties
Merk: | Ozito |
Categorie: | Zaagmachine |
Model: | PXBCS-1830 |
Heb je hulp nodig?
Als je hulp nodig hebt met Ozito PXBCS-1830 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Zaagmachine Ozito
24 December 2024
23 Augustus 2024
23 Augustus 2024
23 Augustus 2024
30 Juli 2024
30 Juli 2024
9 Juli 2023
26 Juni 2023
24 Juni 2023
20 Juni 2023
Handleiding Zaagmachine
- Zaagmachine Bosch
- Zaagmachine AEG
- Zaagmachine DeWalt
- Zaagmachine Ford
- Zaagmachine Al-ko
- Zaagmachine Atika
- Zaagmachine BabyGO
- Zaagmachine Batavia
- Zaagmachine Bavaria
- Zaagmachine Bebe Confort
- Zaagmachine BGU
- Zaagmachine Black Decker
- Zaagmachine Blucave
- Zaagmachine Bort
- Zaagmachine Brennenstuhl
- Zaagmachine Bruder Mannesmann
- Zaagmachine Budget
- Zaagmachine Defort
- Zaagmachine Dolmar
- Zaagmachine Dremel
- Zaagmachine Duro
- Zaagmachine Duro Pro
- Zaagmachine Echo
- Zaagmachine Einhell
- Zaagmachine Elektra Beckum
- Zaagmachine Elu
- Zaagmachine Ergofix
- Zaagmachine Exakt
- Zaagmachine Fein
- Zaagmachine Felisatti
- Zaagmachine Ferm
- Zaagmachine Ferrex
- Zaagmachine Festool
- Zaagmachine Flex
- Zaagmachine Florabest
- Zaagmachine FOM
- Zaagmachine Fuxtec
- Zaagmachine Gamma
- Zaagmachine Gardena
- Zaagmachine Gardenline
- Zaagmachine Germania
- Zaagmachine Global
- Zaagmachine Goon
- Zaagmachine Greenworks
- Zaagmachine Grizzly
- Zaagmachine Gude
- Zaagmachine Gude Pro
- Zaagmachine Hammer
- Zaagmachine Hikoki
- Zaagmachine Hitachi
- Zaagmachine Holzmann
- Zaagmachine Homelite
- Zaagmachine Husqvarna
- Zaagmachine Huvema
- Zaagmachine Hyundai
- Zaagmachine Ideal
- Zaagmachine Kompernass
- Zaagmachine Kress
- Zaagmachine Lux Tools
- Zaagmachine Luxor
- Zaagmachine Maestro
- Zaagmachine Makita
- Zaagmachine Maktec
- Zaagmachine Matrix
- Zaagmachine Max
- Zaagmachine Maxx
- Zaagmachine McCulloch
- Zaagmachine Metabo
- Zaagmachine Milwaukee
- Zaagmachine Parkside
- Zaagmachine Pattfield
- Zaagmachine Plantiflor
- Zaagmachine Powerfix
- Zaagmachine Powerplus
- Zaagmachine Remington
- Zaagmachine Robust
- Zaagmachine Ryobi
- Zaagmachine Scheppach
- Zaagmachine Shindaiwa
- Zaagmachine Silverline
- Zaagmachine Skil
- Zaagmachine Solo
- Zaagmachine Stanley
- Zaagmachine Sterwins
- Zaagmachine Stiga
- Zaagmachine Stihl
- Zaagmachine Tanaka
- Zaagmachine Texas
- Zaagmachine Toledo
- Zaagmachine Toolcraft
- Zaagmachine Topcraft
- Zaagmachine Triton
- Zaagmachine Trotec
- Zaagmachine Troy-Bilt
- Zaagmachine Varo
- Zaagmachine Vonroc
- Zaagmachine Westfalia
- Zaagmachine Workzone
- Zaagmachine Worx
- Zaagmachine Zipper
- Zaagmachine Oregon Scientific
- Zaagmachine Black And Decker
- Zaagmachine Cocraft
- Zaagmachine Draper
- Zaagmachine Meec Tools
- Zaagmachine Lionelo
- Zaagmachine Clarke
- Zaagmachine Genesis
- Zaagmachine Hilti
- Zaagmachine Cobra
- Zaagmachine Hobart
- Zaagmachine ACG
- Zaagmachine Cotech
- Zaagmachine Power Craft
- Zaagmachine Tacklife
- Zaagmachine Truper
- Zaagmachine Fieldmann
- Zaagmachine Mafell
- Zaagmachine Prime3
- Zaagmachine Proxxon
- Zaagmachine Biltema
- Zaagmachine Porter-Cable
- Zaagmachine Sun Joe
- Zaagmachine Yard Force
- Zaagmachine Challenge
- Zaagmachine EGO
- Zaagmachine Hurricane
- Zaagmachine MacAllister
- Zaagmachine Maruyama
- Zaagmachine Sovereign
- Zaagmachine Spear & Jackson
- Zaagmachine Royal Catering
- Zaagmachine Dedra
- Zaagmachine Graphite
- Zaagmachine Narex
- Zaagmachine RIDGID
- Zaagmachine Tryton
- Zaagmachine CMI
- Zaagmachine Garland
- Zaagmachine Herkules
- Zaagmachine Powerworks
- Zaagmachine MSW
- Zaagmachine Sthor
- Zaagmachine Evolution
- Zaagmachine Craftsman
- Zaagmachine Rikon
- Zaagmachine Verto
- Zaagmachine Erbauer
- Zaagmachine Snow Joe
- Zaagmachine Chicago Pneumatic
- Zaagmachine Alpha Tools
- Zaagmachine Hazet
- Zaagmachine Yato
- Zaagmachine Jonsered
- Zaagmachine Qualcast
- Zaagmachine Total
- Zaagmachine Avantco
- Zaagmachine Bestgreen
- Zaagmachine Masport
- Zaagmachine Morrison
- Zaagmachine Stalco
- Zaagmachine Baumr-AG
- Zaagmachine Martha Stewart
- Zaagmachine IKRA
- Zaagmachine MTM
- Zaagmachine Meister Craft
- Zaagmachine Łucznik
- Zaagmachine King Craft
- Zaagmachine Max Bahr
- Zaagmachine Toolson
- Zaagmachine Wolfcraft
- Zaagmachine Kreg
- Zaagmachine Vulcan
- Zaagmachine Anova
- Zaagmachine Challenge Xtreme
- Zaagmachine Pro-Cut
- Zaagmachine Power Smart
- Zaagmachine Backyard Pro Butcher Series
- Zaagmachine EFA
- Zaagmachine Einhell Bavaria
- Zaagmachine McKenzie
- Zaagmachine Prowork
- Zaagmachine Proviel
- Zaagmachine Backyard Pro
- Zaagmachine Ultranatura
- Zaagmachine FIXIT
- Zaagmachine Ergotools Pattfield
- Zaagmachine MyTool
- Zaagmachine Bavaria By Einhell
- Zaagmachine Donau Elektronik
- Zaagmachine Rona
- Zaagmachine TAURUS Titanium
- Zaagmachine Maxbear
- Zaagmachine Extralink
- Zaagmachine Yellow Garden Line
- Zaagmachine Turbo-Silent
Nieuwste handleidingen voor Zaagmachine
23 December 2024
20 December 2024
19 December 2024
19 December 2024
17 December 2024
16 December 2024
16 December 2024
16 December 2024
5 December 2024
5 December 2024