Ozito PSCP-1100 Handleiding

Ozito Pomp PSCP-1100

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PSCP-1100 (6 pagina's) in de categorie Pomp. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
SUBMERSIBLE
CONSTANT
PRESSURE PUMP
1100W
INSTRUCTION MANUAL
SPECIFICATIONS
Motor: 1100W
Max. Flow Rate: 6,000l/h
Max. Head 45m
Max. Immersion: 12m
Max Delivery Pressure: 4.5 bar
Power Cord Length: 15m
Max Particle Size: Ø1mm Clean Water
Outlet: 25mm (1”) Female
Water Temp.: 1°C - 35°C
Weight: 10.4kg
PSCP-1100
STANDARD EQUIPMENT
Submersible Pump
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the
original date of purchase and is intended for DIY (Do It Yourself)
use only. If a product is defective it will be replaced in accordance
with the terms of this warranty. Warranty excludes consumable
parts, for example: O-rings, bearing, seals, gaskets.
WARNING
The following actions will result in the warranty being void.
If the tool has been operated on a supply voltage other
than that specified on the tool.
If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
Failure to perform maintenance as set out within the
instruction manual.
If the tool is disassembled or tampered with in any way.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
1119
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
1. Handle
2. Outlet
3. Power Cord
4. Pump Housing
5. Intake Filter Screen
6. Base
SUBMERSIBLE CONSTANT PRESSURE PUMP
KNOW YOUR PRODUCT
1. HOSE ADAPTOR
ASSEMBLY
1. Screw a suitable
connector (not included)
into the pump housing
outlet by rotating in a
clockwise direction.
WARNING! ENSURE THE PUMP IS DISCONNECTED
FROM THE POWER SUPPLY BEFORE PERFORMING
ANY OF THE FOLLOWING ASSEMBLY.
2. Securely attach the
hose/tube/pipe to the
Hose Adaptor, t hose
clamps (not included)
if you are using exible
hose or tube, and tighten
well.
NOTE: The maximum pumping rate is possible only with the
largest possible line diameter; if smaller hoses or pipes are
connected, the pumping rate will be reduced.
2. SETUP 3. OPERATE
1. Ensure the outlet hose is connected correctly.
2. Ensure the distance from the surface of the water to the
highest point that you wish to deliver the water does not
exceed 45 metres
WARNING!: YOUR PUMP HAS THE CAPACITY
TO PUMP CLEAN WATER WITH A NON SOLID
PARTICLE SIZE OF UP TO 1MM IN DIAMETER.
PREPARATION
1. Immerse the pump in the
water. For deep water,
use a rope (not included)
and secure it to the
handle. Set the pump
in the desired position
within the work area or
tank.
NOTE: Ensure that the
pump is at least 120mm
under the surface of the
water.
2. Insert the plug into the
mains power socket.
The pump will start
3 seconds after the
power is switched on.
3. To stop operation, turn off the mains power.
WARNING! THIS PUMP MUST BE USED WITH
RESIDUAL CURRENT DEVICE RATED 30mA OR
LESS.
Before starting, perform a few simple checks:
3. Ensure the pump is placed on a at and level surface, there
are no obstructions to the suction base and it is clear of mud
or sediment.
WARNING!: NEVER CARRY, LIFT OR PULL UP
THE PUMP BY THE POWER CORD. THIS WILL
DAMAGE THE UNIT.
WARNING!: THIS PRODUCT IS INTENDED
FOR PUMPING WATER IN A HOME DOMESTIC
APPLICATION. DO NOT USE IT FOR
CORROSIVE, ABRASIVE, EXPLOSIVE OR
DANGEROUS LIQUIDS.
MAX.
HEAD 45M
MAX.
IMMERSION
DEPTH 12M
DISCHARGE POINT
POWER
CABLE: 15M
WATER LEVEL
WATER CONTAINER
OUTLET HOSE
OPERATION
WARNING!: BEFORE SUBMERGING THE PUMP
IN WATER, UNWRAP THE POWER CORD AND
ENSURE THE PLUG IS CLEAR OF ANY DAMP
LOCATIONS.
WARNING!: THE PUMP MUST NOT BE USED
WHEN PEOPLE ARE IN THE WATER.
4. Ensure the pump is stable and wont fall over.
15º


Product specificaties

Merk: Ozito
Categorie: Pomp
Model: PSCP-1100

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito PSCP-1100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Pomp Ozito

Handleiding Pomp

Nieuwste handleidingen voor Pomp

Sauermann

Sauermann Omega Handleiding

13 November 2024
Sauermann

Sauermann Delta Handleiding

12 November 2024
Testo

Testo 565i Handleiding

12 November 2024
Simpson

Simpson SCP71008 Handleiding

11 November 2024
MSW

MSW -OP-56-DC Handleiding

5 November 2024
MSW

MSW -FM-N-53 Handleiding

4 November 2024
MSW

MSW -AOP40S Handleiding

15 Oktober 2024
MSW

MSW -MN34M Handleiding

15 Oktober 2024
MSW

MSW -MN34 Handleiding

15 Oktober 2024